Communication & Networking PLCs Operator Interfaces Automation Software Power Supplies Sensors AS-Interface Communication & Networking PS2R AS-Interface Power Supply AS-Interface Power Supply with Universal AC Input Voltage • Input voltage range: 100 to 240V AC • Two output ratings: 73W and 145W • Slim housing style mountable on DIN rails • IP20 fi nger-safe terminals • CE marked (LVD, EMCD) • UL listed (UL 508), CSA (C22.2 No. 950), TÜV (EN60950, EN61010-1) • Noise standards EN55022, EN61000-6-2 compliant • Input indicator (orange) and output indicator (green) • IEC62026-2 compliant Part Numbers AS-Interface Power Supply Output Capacity Input Voltage Output Voltage Part Numbers 73W PS2R-Q30ABL 100 to 240V AC 30.5V DC 145W PS2R-F30ABL USA: 800-262-IDEC Canada: 888-317-IDEC 251 AS-Interface Communication & Networking Specifi cations Model PS2R-Q30ABL PS2R-F30ABL Effi ciency 83% (typical) at the rated input/output Voltage 100 to 240V AC (85 to 264V AC) Frequency 47 to 63 Hz Input 100V AC 1.8A (typical) at the rated load 3.0A (typical) at the rated load Current 220V AC 1.0A (typical) at the rated load 2.0A (typical) at the rated load Leakage Current 3.5mA maximum (UL, CSA, VDE) Inrush Current 30A maximum (25°C at cold start) Rated Voltage 30.5V DC Rated Current 2.4A 4.8A Adjustable Voltage Range N/A Ripple Noise Voltage 300mV p-p maximum (0 to 10 kHz), 50mV p-p maximum (10 to 500 kHz) according to AS-Interface standard Output Input/Load Fluctuation 3% Overall Fluctuation 29.5 to 31.6V DC including input fl uctuation, output fl uctuation, temperature fl uctuation and ripple voltage Delay Time 2 sec maximum (delay in output voltage change from 5V to 26.5V) according to AS-Interface standard Startup Time 1 sec maximum (output voltage change from 21.5V to 29.5V) according to AS-Interface standard Output Holding Time 10ms minimum at 85V AC, rated load 1 Overcurrent Protection 110% (typical), automatic reset 2 Overvoltage Protection 120% minimum Supplementary Undervoltage Protection 95% maximum, automatic reset Functions Input Indicator Orange Output Indicator Green Between inputs and outputs: 3.0 kV AC, 1 minute Dielectric Strength Between inputs and ground: 3.0 kV AC, 1 minute Between outputs and ground: 0.5 kV AC, 1 minute Between inputs and outputs: 100 MΩ minimum (500V DC megger) Insulation Resistance Between inputs andground: 100 MΩ minimum (500V DC megger) Operating Temperature 0 to 60°C (See the derating curve.) Vertical mounting only Storage Temperature –25 to +70°C (no freezing, non-condensation) Operating Humidity 95% RH (non-condensation) 2 10 to 57 Hz amplitude 0.075mm, 57 to 150 Hz acceleration 10 m/s (1G) Vibration Resistance 10 cycles per axis on each of three mutually perpendicular axes 2 Shock Resistance 147 m/s (15G), 11ms duration, 2 shocks per axis, on six mutually perpendicular axes Terminal IP20 Weight (approx.) 800g 1300g Dimensions 120H x 54W x 120D mm 120H x 81W x 120D mm UL 508 listed Safety Standards CSA C22.2 No. 950 EN60950, EN61010 AS-Interface Standard EN50295 (EMI) IEC61000-6-2 EMC Radiated Emission EN55022 class B Conducted Emission EN55022 class B 1. The AS-Interface power supply is provided with an overvoltage protection circuit, but a long period of overload and short-circuit should be avoided. 2. After turning off the input voltage, allow more than 10 seconds before turning on again. 252 www.idec.com Communication & Networking Sensors Power Supplies Automation Software Operator Interfaces PLCs Communication & Networking PLCs Operator Interfaces Automation Software Power Supplies Sensors AS-Interface Communication & Networking Block Diagram Output Derating Terminal Names (Operating temperture is the temperature around the power supply) PS2R-Q30ABL j (L) AC input terminal k (N) AC input terminal (ground side) PS2R-F30ABL 100 l ( ) Ground terminal (protective ground) L N 90 m (AS-i+) AS-Interface + output terminal 80 n (AS-i–) AS-Interface – output terminal 70 60 o ( ) Ground terminal (output side) 50 p (~) Input indicator (goes on when AC input is on) 40 q (AS-i) Output indicator (goes on when DC output is on) 30 20 10 lkj lkj 0 0 10 20 30 40 50 60 Operating Temperature (°C) p p q q AS-i GND GND AS-i + AS-i + AS-i – – o o m m n n Dimensions PS2R-Q30ABL PS2R-F30ABL 54 120 120 81 All dimensions in mm. USA: 800-262-IDEC Canada: 888-317-IDEC 253 120 Output Power (%) 120 AS-Interface Communication & Networking Precautions for Installation 1. Heat Dissipation by Convection 3. Mounting on 35mm-wide DIN Rails Keep minimum spacing of 50mm above and below, and 15mm on both sides Mounting to ensure proper ventilation. To mount the power supply on a DIN rail, place the input terminal side up and put the groove of the power supply on the DIN rail as shown. Press the power supply towards the DIN rail. 50 mm Removing Insert a fl at screwdriver into the slot in the clamp. While pulling out the clamp, turn the power supply bottom out. N L INPUT 100-240 VAC j AS-i 15 mm 15 mm m k l 145w PS2R-F30ABL Mounting on DIN Rail Removing from DIN Rail OUTPUT 30.5VDC 4.8A AS-i+ AS-i– AS-i+ AS-i– Mounting Direction The AS-Interface power supply can be mounted on a vertical plane only. Other mounting directions are not allowed because of heat dissipation. 50 mm Over Current Protection When an overcurrent of 110% of the rated output current fl ows due to an overload, the output voltage drops automatically and intermittent operation 2. Applicable Wires, Ferrules and Tightening Torque starts. When the load returns to normal conditions, the normal output voltage is Ferrule Stranded wire automatically restored. Prevent overload or short-circuitry for a long period of Solid wire time, otherwise the internal elements will be damaged. Ferrule/ Overvoltage Protection Wire When the output voltage exceeds 120% the rated output voltage, the output 2 mm 0.14 to 1.5 0.14 to 0.75 0.14 to 2.5 0.14 to 4 0.14 to 1.5 is turned off. When the output voltage is turned off due to an overvoltage, turn the input off, and after more than 10 seconds, turn the input on again. AWG 26 to 16 26 to 18 26 to 14 26 to 12 26 to 16 Undervoltage Protection 0.6 N•m When the output voltage drops below 95% the rated output voltage, the C output is turned off. When the cause of the error is removed, normal output ø3.5mm 5.4 in•lbs voltage is automatically restored. 254 www.idec.com Communication & Networking Sensors Power Supplies Automation Software Operator Interfaces PLCs