RTE Series Timers RTE Series — Analog Timers Key features of the RTE series include: • 20 time ranges and 10 timing functions •Time delays up to 600 hours • Space-saving package • High repeat accuracy of ± 0.2% • ON and timing OUT LED indicators • Standard 8- or 11-pin and 11-blade termination •2 form C delayed output contacts • 10A Contact Rating UL Listed Cert. No. E9950913332316 (EMC, RTE) File No. E66043 cert. No. BL960813332355 (LVD, RTE) General Specifications Contact Ratings Solid state CMOS Circuit Operation System 2 Form C, DPDT Contact Configuration Multi-Mode (Delay output) Operation Type 0.1sec to 600 hours Time Range Allowable Voltage / 240V AC, 30V DC / 10A 2 (IE60664-1) Pollution Degree Allowable Current III (IE60664-1) Over voltage category Maximum Permissible 1800 cycles per hour AF20 100-240V AC(50/60Hz) Operating Frequency Rated Operational G AD24 24V AC(50/60Hz)/24V DC Voltage Resistive 10A 240V AC, 30V DC D12 12V DC Rated Inductive 7A 240V AC, 30V DC AF20 85-264V AC(50/60Hz) Load Voltage Tolerance AD24 20.4-26.4V AC(50/60Hz)/21.6-26.4V DC Horse Power Rat- 1/6 HP 120V AC, 1/3 HP D12 10.8-13.2V DC ing 240V AC Rated Voltage x10% minimum Input off Voltage 500,000 op. minimum Electrical -20 to +65ºC (without freezing) (Resistive) Ambient Operating Temperature Life Ambient Storage and Mechanical 50,000,000 op. minimum -30 to +75ºC (without freezing) Transport Temperature 35 to 85%RH (without condensation) Relative Humidity 80kPa to 110kPa (Operating), 70kPa to 110kPa (Transport) Atmospheric Pressure 100msec maximum Reset Time ±0.2%, ±20msec* Repeat Error ±0.2%, ±20msec* Voltage Error ±0.5%, ±20msec* Temperature Error ±10% maximum Setting Error 100MΩ minimum (500V DC) Insulation Resistance Between power and output terminals: 2000V AC, 1 minute Dielectric Strength Between contacts of different poles: 2000V AC, 1 minute Between contacts of the same pole:1000V AC, 1 minute 10 to 55Hz amplitude 0.5mm2 hours in each of 3 axes Vibration Resistance 2 Operating extremes: 98m/sec (10G) 2 Shock Resistance Damage limits: 490m/sec (50G) 3 times in each of 3 axes IP40 (enclosure) (IEC60529) Degree of Protection TYPE RTE-P1, -B1 RTE-P2, -B2 RTE Table of Contents 120V AC/60Hz 6.5VA 6.6VA SpeciŢcations —G-8 AF20 240V AC/60Hz 11.6VA 11.6VA Part Number Guide — G-9 24V AC 60Hz/DC 3.4VA/1.7W 3.5VA/1.7W D12 1.6W 1.6W Part Number List — G-9 Free Mounting Position RTE Timing Diagrams — G-10 RTE-P1, P2 40Hx 36W x 77.9D mm RTE Accessories — G-12 Dimensions RTE-B1, B2 40Hx 36W x 74.9D mm Instructions: Setting Timer — G-11 RTE-P1 RTE-P2 RTE-B1, -B2 Weight (Approx.) 87g 89g 85g RTE Dimensions — G-13 *For the value of the error against a preset time, whichever the largest. General Timing Diagrams — G-4 G-8 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC Timers Power Consumption (Approx.) Timers Timers RTE Series Part Numbering Guide RTE series part numbers are composed of 4 part number codes. When ordering a RTE series part, select one code from each category. Example: RTE-P1AF20 RTE P 1 AF20 ➀ Series ➁ Terminal➂ Function➃ Input Voltage Style Group Part Numbers: RTE Series Description Part Number Code Remarks ➀ Series RTE series RTE For internal circuits, see next page. Pin P ➁ Terminal Style Select one only. Blade B ON-delay, interval, cycle OFF, cycle ON 1 ➂ Function Each function group has different timing functions. ON-delay, cycle OFF, cycle ON, signal See page G-4. Group 2 ON/OFF delay, OFF-delay, one-shot 100 to 240V AC(50/60Hz) AF20 ➃ Input Voltage 24V AC(50/60Hz)/24V DC AD24 12V DC D12 Part Number List G Part Numbers Power Triggered Start Input Triggered Voltage 8-Pin Blade 11-Pin Blade 12V DC RTE-P1D12 RTE-B1D12 RTE-P2D12 RTE-B2D12 24V AC/DC RTE-P1AD24 RTE-B1AD24 RTE-P2AD24 RTE-B2AD24 100-240V AC RTE-P1AF20 RTE-B1AF20 RTE-P2AF20 RTE-B2AF20 Time Range Table Time Range Determined by Time Range Selector & Dial Selector Dial 0 - 1 0 - 3 0 - 10 0 - 30 0 - 60 Second 0.1 sec - 1 sec 0.1 sec - 3 sec 0.2 sec - 10 sec 0.6 sec - 30 sec 1.2 sec - 60 sec Minute 1.2 sec - 1 min 3.6 sec - 3 min 12 sec - 10 min 36 sec - 30 min 1.2 min - 60 min Hour 1.2 min - 1 hr 3.6 min - 3 hr 12 min - 10 hr 36 min - 30 hr 1.2 hr - 60 hr 10 Hours 12 min - 10 hr 36 min - 30 hr 2 hr - 100 hr 6 hr - 300 hr 12 hr - 600 hr www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC G-9 Range RTE Series Timers Timing Diagrams RTE-P1 RTE-P2 RTE-B1 RTE-B2 1. RTE-P2: Do not apply voltage to terminals #5, #6 & #7. external external 2. RTE-B1, -B2: Do not apply voltage to terminals #2, #5 & #8. start control start control 1 3 3. IDEC sockets are as follows: RTE-P1: SR2P-06* pin type socket, 2 4 5 1 2 3 RTE-P2: SR3P-05* pin type socket, RTE-B1, -B2: SR3B-05* blade 5 6 6 3 4 8 type socket, (*-may be followed by suffix letter A,B,C or U). 4 5 6 7 8 9 2 7 3 9 7 8 9 1 8 A B 2 10 1 11 A B (~/+) (~/-) (~/+) (~/-) (~/+) (~/-) (~/+) (~/-) RTE-P1, -B1 A: ON-Delay 1 (power start) B: Interval (power start) Set timer for desired delay, apply power to coil. Contacts transfer immediately, and Set timer for desired delay, apply power to coil. Contacts transfer after preset time return to original position after preset time has elapsed. Reset occurs with removal has elapsed, and remain in transferred position until timer is reset. Reset occurs of power. with removal of power. Item Terminal No. Operation Item Terminal No. Operation (1)2-7 (1)2-7 Power Power (2)A-B (2)A-B (1)1-4,5-8 (1)1-4,5-8 (NC) (NC) (2)1-7,3-9 (2)1-7,3-9 Delayed Delayed Contact (1)1-3,6-8 Contact (1)1-3,6-8 (NO) (NO) (2)4-7,6-9 (2)4-7,6-9 PWR PWR Indicator Indicator OUT OUT Set Time Set Time T T C: Cycle 1 (power start, OFF first) D: Cycle 3 (power start, ON first) Set timer for desired delay, apply power to coil. First transfer of contacts occurs Functions in same manner as Mode C, with the exception that first transfer of after preset delay has elapsed, after the next elapse of preset delay contacts return contacts occurs as soon as power is applied. The ratio is 1:1. Time On = Time Off to original position. The timer now cycles between on and off as long as power is applied (duty ratio 1:1). Item Terminal No. Item Terminal No. Operation Operation (1)2-7 (1)2-7 Power Power (2)A-B (2)A-B (1)1-4,5-8 (1)1-4,5-8 (NC) (NC) Delayed (2)1-7,3-9 Delayed (2)1-7,3-9 Contact (1)1-3,6-8 Contact (1)1-3,6-8 (NO) (NO) G (2)4-7,6-9 (2)4-7,6-9 PWR PWR Indicator Indicator OUT OUT Set Time Set Time T T T T RTE-P2, -B2 A: ON-Delay 2 (signal start) B: Cycle 2 (signal start, OFF first) When a preset time has elapsed after the start input turned on while power is on, When the start input turns on while power is on, the output oscillates at a preset the NO output contact goes on. cycle (duty ratio 1:1), starting while the NO contact off. Item Terminal No. Operation Item Terminal No. Operation (A)2-10 (A)2-10 Power Power (B)A-B (B)A-B (A)5-6 (A)5-6 Start Start (B)2-5 (B)2-5 (A)1-4,8-11 (A)1-4,8-11 (NC) (NC) (B)1-7,3-9 (B)1-7,3-9 Delayed Delayed Contact (A)1-3,9-11 Contact (A)1-3,9-11 (NO) (NO) (B)4-7,6-9 (B)4-7,6-9 PWR PWR Indicator Indicator OUT OUT Set Time Set Time T TT TT T TTTT Ta C: Cycle 4 (signal start, ON first) D: Signal ON/OFF-Delay When the start input turns on while power is on, the NO output contact goes on. When the start input turns on while power is on, the NO contact goes on. The When a preset time has elapsed while the start input remains on, the output contact output oscillates at a preset cycle (duty ratio 1:1). goes off. When the start input turns off, the NO contact goes on again. When a preset time has elapsed after the start input turned off, the NO contact goes off. Item Terminal No. Operation Item Terminal No. Operation (A)2-10 (A)2-10 Power Power (B)A-B (B)A-B (A)5-6 (A)5-6 Start Start (B)2-5 (B)2-5 (A)1-4,8-11 (A)1-4,8-11 (NC) (NC) (B)1-7,3-9 (B)1-7,3-9 Delayed Delayed Contact (A)1-3,9-11 Contact (A)1-3,9-11 (NO) (NO) (B)4-7,6-9 (B)4-7,6-9 PWR PWR Indicator Indicator OUT OUT Set Time Set Time TT TT T TTTTa TT TTaT Ta E: Signal OFF-Delay F: One-Shot (signal start) When power is turned on while the start input is on, the NO output contact goes When the start input turns on while power is on, the NO output contact goes on. on. When a preset time has elapsed after the start input turned off, the NO output When a preset time has elapsed, the NO output contact goes off. contact goes off. Item Terminal No. Operation Item Terminal No. Operation (A)2-10 (A)2-10 Power Power (B)A-B (B)A-B (A)5-6 (A)5-6 Start Start (B)2-5 (B)2-5 (A)1-4,8-11 (A)1-4,8-11 (NC) (NC) (B)1-7,3-9 (B)1-7,3-9 Delayed Delayed Contact (A)1-3,9-11 Contact (A)1-3,9-11 (NO) (NO) (B)4-7,6-9 (B)4-7,6-9 PWR PWR Indicator Indicator OUT OUT Set Time Set Time TT Ta Ta TTa Note : T=Set Time, Ta=Shorter than set time, (1): RTE-P1, (2): RTE-B1, (A): RTE-P2, (B): RTE-B2 G-10 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC Timers Timers Timers RTE Series Temperature Derating Curves Mounting B Mounting A 10A 7A 7A 5A Mounting A Mounting B Derating Curve Derating Curve 50ºC 65ºC 50ºC 65ºC Ambient Temperature Ambient Temperature Instructions Types Switch Settings 1. Turn the selectors securely using a ţat Power Voltage RTE-P1AF20 screwdriver 4mm wide (maximum). AF20: 100 to 240V AC(50/60Hz) AD24: 24V AC(50/60Hz)/24V DC Note that incorrect setting may cause D12: 12V DC 3 malfunction. Do not turn the selectors Connection type Operation Mode P: Pin beyond their limits. 1: No Control Signal 2: Control Signal B: Blade 1 A: ON-Delay 1 A: ON-Delay 2 2 B: Interval B: Cycle 2 2. Since changing the setting during timer C: Cycle 1 C: Cycle 4 1 Operation Mode operation may cause malfunction, turn D: Cycle 3 D: Signal ON/OFF-Delay Selector E: Signal OFF-Delay power off before changing. 2 Scale Selector F: One-Shot 3 Time Range Selector Installation of Hold-Down Springs DIN Rail Mount Socket Insert the springs into the outer Insert the springs slots with the projections into the slots. G facing inside. Socket SR3P-05 Hold-down Spring (sold separately) SFA-203 (use two springs) Socket SR2P-06 Hold-down Spring (sold separately) SFA-202 (use two springs) Safety Precautions Special expertise is required to use Electronic Timers. • Failure to turn power off may cause electrical shocks or fire hazard. • All Electronic Timers are manufactured under IDEC's rigorous qual- • Do not use the Electronic Timer for an emergency stop circuit or ity control system, but users must add a backup or fail safe provision interlocking circuit. If the Electronic Timer should fail, a machine to the control system when using the Electronic Timer in applica- malfunction, breakdown, or accident may occur. tions where heavy damage or personal injury may occur should the Caution Electronic Timer fail. Caution notices are used where inattention might cause personal • Install the Electronic Timer according to instructions described in injury or damage to equipment. this catalog. • Make sure that the operating conditions are as described in the spec- • The Electronic Timer is designed for installation in equipment. Do ifications. If you are uncertain about the specifications, contact not install the Electronic Timer outside equipment. IDEC in advance. • Install the Electronic Timer in environments described in the specifi- • In these directions, safety precautions are categorized in order of cations. If the Electronic Timer is used in places where it will be importance under Warning and Caution. subjected to high-temperature, high-humidity, condensation, corro- sive gases, excessive vibrations, or excessive shocks, then electrical Warnings Warning notices are used to emphasize that improper operation may shocks, fire hazard, or malfunction could result. cause severe personal injury or death. • Use an IEC60127-approved fuse and circuit breaker on the power and output line outside the Electronic Timer. • Turn power off to the Electronic timer before starting installation, • Do not disassemble, repair, or modify the Electronic Timer. removal, wiring, maintenance, and inspection on the Electronic • When disposing of the Electronic Timer, do so as industrial waste. Timer. www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC G-11 Allowable Current Allowable Current RTE Series Timers DIN Rail Mounting Accessories Part Numbers: DIN Rail/Surface Mount Sockets and Hold-Down Springs DIN Rail Mount Socket Applicable Hold-Down Springs Style Appearance Use with Timers Part No. Appearance Part No. 11-Pin Screw Terminal RTE-P2 SR3P-05 (dual tier) SFA-203 11-Pin FingerSafe Socket RTE-P2 SR3P-05C 8-Pin Screw Terminal RTE-P1 SR2P-06 SFA-202 RTE-B1 11-Blade Screw Terminal SR3B-05 RTE-B2 G DIN Mounting Rail — BNDN1000 Length 1000mm Panel Mounting Accessories Part Numbers: Flush Panel Mount Adapter and Sockets that use an Adapter Accessory Description Appearance Use with Part No. Panel Mount Adaptor for ţush panel All RTE timers RTB-G01 mounting RTE timers Adapter 8-pin screw terminal RTE-P1 SR6P-M08G (Shown: SR6P-M08G Wiring Socket Adapter) 11-pin screw terminal RTE-P2 SR6P-M11G Sockets for use with Panel 8-pin solder terminal RTE-P1 SR6P-S08 Mount Adapter 11-pin solder terminal RTE-P2 SR6P-S11 No hold down clips are available for flush panel mounting applications. G-12 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC Timers Timers Timers RTE Series Dimensions 77.9 13.0 36.0 13.7 RTE-P1 (8 pin) Terminal Style RTE-P2 (11 pin)Terminal Style 7.3 RTE-B1/RTE-B2 (11 blade) Terminal Style G Panel Mount Adapter RTE Timer, 8-Pin and 11-Pin with SR6P-S08 or SR6P-S11 98 maximum Panel Thickness 0.8 to 5mm Back Wiring Socket 48 11 61.2 RTE Timer, 8-Pin with SR6P-M08G 8-M3.5 Terminal Screw Panel Thickness 0.8 to 5mm 44.6 3.5 max. 5.6 min. ø3.6 min. 34 5 6 6.9 max. 2187 7 9.8 × 3 80.5 RTE Timer, 11-Pin with SR6P-M11G 11-M3.5 Teminal Screws 45 16.7 5.8 min. 3.5 max. 217 11 6 ø3.6 min. 5 6.9 max. 43 8 9 10 30.5 7 92 8.5 × 4 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC G-13 40.0 48 45 34 44.6 30.4 1.7 42.5 General Instructions Timers General Instructions for All Timer Series Load Current Time Setting With inductive, capacitive, and incandescent lamp loads, inrush current more The time range is calibrated at its maximum time scale; so it is desirable to than 10 times the rated current may cause welded contacts and other undes- use the timer at a setting as close to its maximum time scale as possible. For ired effects. The inrush current and steady-state current must be taken into a more accurate time delay, adjust the control knob by measuring the operat- consideration when specifying a timer. ing time with a watch before application. Input Contacts Contact Protection Use mechanical contact switch or relay to supply power to the timer. When Switching an inductive load generates a counter-electromotive force (back driving the timer with a solid-state output device (such as a two-wire proxim- EMF) in the coil. The back EMF will cause arcing, which may shorten the con- ity switch, photoelectric switch, or solid-state relay), malfunction may be tact life and cause imperfect contact. Application of a protection circuit is caused by leakage current from the solid-state device. Since AC types com- recommended to safeguard the contacts. prise a capacitive load, the SSR dielectric strength should be two or more times the power voltage when switching the timer power using an SSR. Temperature and Humidity Use the timer within the operating temperature and operating humidity Generally, it is desirable to use mechanical contacts whenever possible to ranges and prevent freezing or condensation. After the timer has been stored apply power to a timer or its signal inputs. When using solid state devices, be below its operating temperature, leave the timer at room temperature for a cautious of inrushes and back-EMF that may exceed the ratings on such sufŢcient period of time to allow it to return to operating temperatures before devices. Some timers are specially designed so that signal inputs switch at a use. lower voltage than is used to power the timer (models designated as “B" type). Environment Avoid contact between the timer and sulfurous or ammonia gases, organic solvents (alcohol, benzine, thinner, etc.), strong alkaline substances, or strong acids. Do not use the timer in an environment where such substances are prevalent. Do not allow water to run or splash on the timer. Vibration and Shock Excessive vibration or shocks can cause the output contacts to bounce, the timer should be used only within the operating extremes for vibration and shock resis- tance. In applications with signiŢcant vibration or shock, use of hold down springs or clips is recommended to secure a timer to its socket. G Timing Accuracy Formulas Timing accuracies are calculated from the following formulas: Repeat Error = ± 1 x Maximum Measured Value – Minimum Measured Value x 100% 2 Maximum Scale Value Voltage Error = ± Tv - Tr x 100% Tr T : Average of measured values at voltage V v T Average of measured values at the rated voltage r: Temperature Error = ± Tt - T20 x 100% T20 T : Average of measured values at °C t T : Average of measured values at 20°C 20 Setting Error = ± Average of Measured Values - Set Value x 100% Maximum Scale Value G-68 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC Timers