Manufacturers
IDEC CORPORATION SA-203
Description
Surface Mount End Connector For Use On Ends Of Socket Groupings When Surface Mounting
SA-203
Part Number
SA-203
Price
Request Quote
Manufacturer
IDEC CORPORATION
Lead Time
Request Quote
Category
Thermal Management » Misc Products
Specifications
Manufacturer
IDEC Corporation
Manufacturers Part #
SA-203
Lead Time
9 Week Lead Time
Sub-Categories
Miscellaneous Tools and Supplies
Factory Pack Quantity
1
Datasheet
Extracted Text
Sockets Sockets SH Series: PCB Mount SH Series: PC Board Mount Sockets ø2.4 holes 6.8 Terminal Arrangement 3- 18 min. 1 4.4 5 9 13 14 18 3 (Bottom View) SH1B-62 11 2-ø2 holes Style 5-blade 15 2 Terminal Solder/PCB mount 1.5 (Tolerance ±0.1) ∗ 36 min. when using 12.2 Electrical Rating 250V, 10A hold-down springs Compatible Relay RH1B Hold-Down Spring SY4S-51F1 SFA-301 (top notch), Hold-Down Clip SFA-302 (side notch) F 21.5 min. Terminal Arrangement 2.85 1 4 15.5 5 8 10 9 12 SH2B-62 13 14 Style 8-blade 3 (Bottom View) 21.2 11 Terminal Solder/PCB mount 15 8-ø2.4 holes Electrical Rating 300V, 10A Compatible Relay RH2B 2 (Tolerance ±0.1) ∗ 34 min. when using hold-down springs Hold-Down Spring SY4S-51F1, SY4S-02F1 SFA-301 (top notch), Hold-Down Clip SFA-302 (side notch) 36 min. Terminal Arrangement 21.3 7.35 1 2 4 10 10 5 6 8 9 10 12 13 14 36 3 (Bottom View) SH3B-62 11 Style 11-blade 15 11-ø2.4 holes Terminal Solder/PCB mount 2 ∗ 36 min. when using (Tolerance ±0.1) 30.2 Electrical Rating 300V, 10A hold-down springs RH3B, *RH2LB Compatible Relay (*latching relay) Hold-Down Spring SY4S-51F1, SY4S-02F1 SFA-301 (top notch), Hold-Down Clip SFA-302 (side notch) 1. For socket mounting accessories, see page F-29. All dimensions are in mm. 2. For hold-down clip/spring selections, see page F-4. www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC F-25 31 31 29 0.3 0.3 25.4 0.3 25.4 25.4 4.7 31 min.∗ 11.85 31 min.∗ 6.95 12.5 4.7 4.7 6.65 5.95 12.5 29 min.∗ 5.65 6.6 6.6 SH/SY Series: PCB Mount Sockets SH Series: PC Board Mount Sockets, continued Terminal Arrangement 6.85 45 min. 31.3 1 2 3 4 5 6 7 8 10 10 10 9 10 11 12 13 14 3 45 (Bottom View) 11 SH4B-62 15 Style 14-blade 14-ø2.4 holes 2 Terminal Solder/ PCB mount ∗ 36 min. when using 39.2 (Tolerance ±0.1) hold-down springs Electrical Rating 300V, 10A Compatible Relay RH4B Hold-Down SY4S-51F1, SH4B-02F1 Springs SFA-301 (top notch), Hold-Down Clip SFA-302 (side notch) F SY Series: PC Board Mount Sockets 13.6 min. 4.4 Terminal Arrangement 1 4 5 8 9 12 SY2S-61 13 14 Style 8-blade (Bottom View) 18 3 Terminal Solder/PCB mount 11 8-ø2 holes 15 Electrical Rating 300V, 7A ∗ 19.2 min. when using (Tolerance ±0.1) 1.5 hold-down springs Compatible Relay RY2S, RY22S 12.2 Hold-Down Spring SY4S-51F1 SFA-301 (top notch), Hold-Down Clip SFA-302 (side notch) All dimensions are in mm. 1. For socket mounting accessories, see page F-29. 2. For hold-down clip/spring selections, see page F-4. F-26 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC Sockets 31 31 0.3 0.3 25.4 25.4 31 min.∗ 12.5 4.7 14.2 min.∗ 6.65 16.8 6.6 10.4 4.1 9 Sockets 13.2 8.8 4.4 Sockets SY Series: PCB Mount SY Series: PC Mount Sockets, continued 13.2 13.8 min. 8.8 4.4 Terminal Arrangement 1 2 3 4 5 6 7 8 SY4S-61 9 10 1112 Style 14-blade 13 14 27 3 (Bottom View) Terminal Solder/PCB mount 11 15-ø2 holes Electrical Rating 300V, 7A 15 RY4S, RY42S, RM2S, (Tolerance ±0.1) ∗ 19.2 min. when using 1.5 Compatible Relay *RY2KS, RU4S, RU42S, RU2S hold-down springs (*latching relay) 21.2 Compatible Timer GT5Y Hold-Down Spring SY4S-51F1, SY4S-02F1 SFA-301 (top notch; except Hold-Down Clip GT5Y and RY2KS) SFA-302 (side notch for all) F 8.2 min.∗∗ Terminal Arrangement 2 3 4 1 5 6 7 8 SY4S-62 9 10 1112 13 14 Style 14-blade 21.2 3 (Bottom View) Terminal Solder/PCB mount 15-ø2 holes 11 Electrical Rating 250V, 7A 15 (Tolerance ±0.1) RY4S, RY42S, RU4S, Compatible Relay RU42S, *RY2KS 1.5 ∗17.2 min. when using a hold-down spring. (*latching relay) ∗∗13.2 min. when using a hold-down spring for the relay with check button. Compatible Timer GT5Y SY4S-51F1, SY4S-51F3, SY4S-51F4, *SY4S-02F1, Hold-Down Spring *SY4S-02F3 (*when mounting a relay with check button) All dimensions are in mm. 1. For socket mounting accessories, see page F-29. 2. For hold-down clip/spring selections, see page F-4. www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC F-27 29 31 0.3 0.3 25.4 14.2 min.∗ 16.8 12.2 min.∗ 16.8 10.4 10.4 1.4 4.1 1.4 4.1 9 9 Sockets Sockets Accessories Accessories SA-203 SA-204 SA-203 M4 screw 18mm washer hold-down 5mm spring Description Appearance Use with Part No. Remarks IDEC offers a low-proŢle DIN rail (BNDN1000). The BNDN1000 is designed to accommodate snap- Aluminum mount sockets. Made of durable DIN Rail All DIN rail sockets BNDN1000 extruded aluminum, the BNDN-1000 (1 meter length) measures 0.413 in height and 1.37 (35mm) in width (DIN standard). Standard length is 39" (1,000mm). DIN Rail DIN rail BNL5 9.1 mm wide. End Stop F For use on ends of socket groupings SA-203 when surface mounting. Surface Mount SY2S, SY4S, SR3B, SH1B, SH2B, SH3B, SH4B End Connector For use between adjoining sockets SA-204 when surface mounting. Surface Mount SY2S, SY4S, SR3B, SH1B, For use between adjoining sockets SA-405 SH2B, SH3B, SH4B when surface mounting. Connector DIN Rail Spacer All DIN rail sockets SA-406 SY4S-51, SH2B-51 SA-402 11.42" length with 10 holes. Steel Mounting Plates (for panel mount sockets) SY4S-51, SH2B-51 SA-403 23.33" length with 21 holes. RH2B, RM2S, RY4S, RY42S, RH-01 RU4S, RU42S Relay Holders For diagram, see next page. RY2S, RH1B RH-03 For use with hold-down springs Horseshoe clip for all Replacement Hold- (bale wire types). DIN rail sockets except Y778-011 or DIN rail mount sockets. Down Spring Anchor SR*P-05(C) 2 pieces included with each socket. Hold-Down Spring for For SR2P-05, SR2P-05C, Chair clip for SR*P-05(C) Y703-102 SR3P-05, SR3P-05C SR*P-05(C) www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC F-29 Instructions Sockets Instructions Mounting Snap-Mount Sockets Snap-mount sockets are designed to mount on the BNDN-1000 Mount mounting rail. The built-in mounting clip eliminates mounting hard- ware and reduces mounting time by 80%. To mount see Figure 1. Place the end of the socket (end opposite of mounting clip against the outer edge of the rail). Press the socket down Ţrmly until the clip snaps onto the mounting rail. To remove Figure 1 see Figure 2. Pull out the mounting clip with a screwdriver, and lift the socket. Remove For spacing between adjoining sockets, use the SA-406 DIN rail spacer. Spacers are 0.195" wide. Spacing can be adjusted accord- ing to the number of spacers added. Spacers snap on and off easily Hold-Down Spring like snap-mount sockets. To prevent side-to-side movement, use a BNL-5 end clip at each Figure 2 end of every socket row. Mounting Relay Holders F RH-01 or -03 Mount directly onto panel boards in two alternate positions: A and B (see Figure 1). To mount the relay into the holder, hook the bottom Figure 1 edge of the relay case (coil terminal side) onto the relay holder (see Figure 2). Push down until the relay snaps into place. Figure 2 Mounting Hold-Down Springs Take the two anchor clips (horseshoe / U-shaped piece) that come with the socket and insert into the slits on both sides of the socket. Make sure the raised notches on the anchor clip face into the socket. Plug relay into socket Insert the open ends of the hold-down spring into either the Ţrst or second hole of the anchor clip. The relay-spring combination will determine which hole should be used. Slide spring over relay. F-30 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC Sockets Sockets Sockets Dimensions Dimensions Surface Mount Sockets (SH2B-02) IDEC surface mount sockets (SH2B-02) are also designed to mount individually or collectively on a ţat surface without the use of a DIN rail. Use the mounting screw between adjoining sockets and at the outer ends of the row of sockets. Dimension Table Socket Part No. Dimension A SH2B-02 1.14" AA A 1. Drawing is not to scale. F Snap-Mount Sockets Snap-mount sockets are designed to mount individually or collectively without using a rail. Use a SA-405 connector or SA-204 connector between adjoining sockets (see Figures 1 and 2). Use the SA-203 end connector at the outer ends of each socket row when using the SA-204 connector (see Figure 2). Dimension Table Socket Part No. Dim. B Dim. C Dim. D SY2S-05, SY2S-05C 0.669" 0.826" 0.866" SY4S-05, SY4S-05C 1.024" 1.181" 1.220" SR3B-05 1.496" 1.693" 1.732" SH1B-05, SH1B-05C 0.630" 0.787" 0.827" SH2B-05, SH2B-05C 1.024" 1.181" 1.220" SH3B-05, SH3B-05C 1.417" 1.575" 1.614" SH4B-05, SH4B-05C 1.811" 1.969" 2.008" Using an SA-406 Connector BC C C C 0.165" Hole Using SA-203 or SA-204 Connectors or M4 Tapped DD D 2. Drawings are not to scale. www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC F-31 Dimensions Sockets Dimensions, continued Collective Panel Mounting SH and SY series panel mount sockets are designed to mount collec- tively in panel cut-outs. Insert socket with mounting springs facing the top and bottom edge of the panel cut-out. Push the socket until the SY4S-51 mounting spring clips onto the panel. (See Figure 1.) Dimension Table Part No. Width Relay SY4S-51 1.063" RY4S, RY42, RY2KS, RM2S Figure 1 SH4B-51 1.772" RH4B SH3B-51 1.418" RH3B, RH2LB RY2KS RH2B SH2B-51 1.063" RH2B RH1B SH1B-51 0.709" RH1B RM2S SY2S-51 0.709" RY2S, RY22S How to Calculate Cutout Length (L) Cutout L = A (Total Overall Width of Each Socket) – 0.221" (+ 0", – 0.020") Example: A = Total Overall Width of Each Socket F Cutout L = A – 0.221" (+ 0", – 0.020") SY2S-51 SY4S-51 SY4S-51 SY4S-51 SH1B-51 SY4S-51 SY2S-51 SH1B-51 SH2B-51 L = [0.709" + 1.063" + 1.063" + 0.709" + 1.063" + 0.709" + 1.063" + 1.063"] – 0.221" = 7.93" L = 7.93" (+ 0", – 0.020") Mounting Plate F-32 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC Sockets
Frequently asked questions
How does Electronics Finder differ from its competitors?
Is there a warranty for the SA-203?
Which carrier will Electronics Finder use to ship my parts?
Can I buy parts from Electronics Finder if I am outside the USA?
Which payment methods does Electronics Finder accept?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
AL1 LED Illuminated Pushbuttons And Pilot Lights AL2M-LK1-G
Miniature Switches And Pilot Devices: 16Mm AL6H-LK3-A
Rectangular Lens for Pilot Lights AL6H-LK3-G
Rectangular Lens for Pilot Lights AL6H-LK3-R
Rectangular Lens for Pilot Lights AL6H-LK3-S
Rectangular Lens for Pilot Lights AL6H-LK3-W
Request a Quote
The quote request has been received
Close
Facing challenges or have inquiries? Feel free to contact us!
Call Us +1-469-283-2440
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods