2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP Part Number: AA2810ASES/J3 Hyper Red Features Description z 2.8mmX0.8mm right angle SMT LED, 1.2mm thickness. The Hyper Red device is based on light emitting diode chip z Low power consumption. made from AlGaInP. z Ideal for backlight and indicator. z Various colors and lens types available. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.0039") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 2. As silicone encapsulation is permeable to gases, some corrosive substances such as H S might corrode silver plating of 2 leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917 Selection Guide Iv (mcd) [2] Viewing @ 20mA Angle [1] Part No. Dice Lens Type Min. Typ. 2θ1/2 1300 1800 AA2810ASES/J3 Hyper Red (AlGaInP) Water Clear 110° *400 *550 Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Hyper Red 640 nm IF=20mA λD [1] Dominant Wavelength Hyper Red 625 nm IF=20mA Δλ1/2 Spectral Line Half-width Hyper Red 25 nm IF=20mA C Capacitance Hyper Red 27 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 2.2 2.8 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 84 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917 Hyper Red AA2810ASES/J3 SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917 AA2810ASES/J3 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917 PACKING & LABEL SPECIFICATIONS AA2810ASES/J3 SPEC NO: DSAK2442 REV NO: V.4A DATE: MAR/02/2013 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005917