3.0x2.0mm SURFACE MOUNT LED LAMP PRELIMINARY SPEC Part Number: AA3020APBC/Z BLUE ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Description z 3.0MM X 2.0MM, 1.4MM HIGH, ONLY MINIMUM The Blue source color devices are made with InGaN Light SPACE REQUIRED. Emitting Diode. z SUITABLE FOR COMPACT OPTOELECTRONIC Static electricity and surge damage the LEDS. APPLICATIONS. It is recommended to use a wrist band or anti-electrostatic z LOW POWER CONSUMPTION. glove when handling the LEDs. z PACKAGE : 2000PCS / REEL. All devices, equipment and machinery must be electrically z MOISTURE SENSITIVITY LEVEL : LEVEL 4. grounded. z RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAH5316 REV NO: V.2 DATE: JUN/27/2007 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI ERP: 1201003014 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might leads to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Outside impact may scratch the silicone lens or damage the internal circuitry. 4. During surface-mounting, the pickup capillary diameter should be larger than the silicone lens to insure the capillary does not scratch or damage the lens. SPEC NO: DSAH5316 REV NO: V.2 DATE: JUN/27/2007 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI ERP: 1201003014 Selection Guide Iv (mcd) [2] Viewing @ 20mA Angle [1] Part No. Dice Lens Type Min. Typ. 2θ1/2 AA3020APBC/Z BLUE (InGaN) WATER CLEAR 110 280 120° Notes: 1.θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2.Luminous Intensity / Luminous Flux: +/-15% Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Blue 458 nm IF=20mA Dominant Wavelength Blue 465 nm IF=20mA λD [1] Δλ1/2 Spectral Line Half-width Blue 22 nm IF=20mA C Capacitance Blue 110 pF VF=0V;f=1MHz VF [2] Forward Voltage Blue 3.2 3.7 V IF=20mA IR Reverse Current Blue 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Blue Units Power dissipation 111 mW DC Forward Current 30 mA Peak Forward Current [1] 100 mA Reverse Voltage 5 V Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAH5316 REV NO: V.2 DATE: JUN/27/2007 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI ERP: 1201003014 Blue AA3020APBC/Z SPEC NO: DSAH5316 REV NO: V.2 DATE: JUN/27/2007 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI ERP: 1201003014 AA3020APBC/Z Recommended Soldering Pattern (Units : mm; Tolerance: ±0.1) Tape Specifications (Units : mm) SPEC NO: DSAH5316 REV NO: V.2 DATE: JUN/27/2007 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI ERP: 1201003014 PACKING & LABEL SPECIFICATIONS AA3020APBC/Z SPEC NO: DSAH5316 REV NO: V.2 DATE: JUN/27/2007 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI ERP: 1201003014