4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP ATTENTION Part Number: AA4040ZGS Green OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Description z Single color. The Green source color devices are made with InGaN z Suitable for all SMT assembly and solder process. on Sapphire Light Emitting Diode. z Available on tape and reel. Static electricity and surge damage the LEDS. z Ideal for backlighting. It is recommended to use a wrist band or anti-electrostatic z Package : 500pcs / reel. glove when handling the LEDs. z Moisture sensitivity level : level 3. All devices, equipment and machinery must be electrically z RoHS compliant. grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL0886 REV NO: V.4B DATE: MAR/02/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201006684 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. As silicone encapsulation is permeable to gases, some corrosive substances such as H S might corrode silver plating of 2 leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL0886 REV NO: V.4B DATE: MAR/02/2013 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201006684 Selection Guide Iv (mcd) [2] Viewing @ 20mA Angle [1] Part No. Dice Lens Type Min. Typ. 2θ1/2 AA4040ZGS Green (InGaN) Water Clear 400 800 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Green 515 nm IF=20mA λD [1] Dominant Wavelength Green 525 nm IF=20mA Δλ1/2 Spectral Line Half-width Green 30 nm IF=20mA C Capacitance Green 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 3.3 4.1 V IF=20mA IR Reverse Current Green 50 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 102.5 mW DC Forward Current 25 mA Peak Forward Current [1] 150 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAL0886 REV NO: V.4B DATE: MAR/02/2013 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201006684 Green AA4040ZGS SPEC NO: DSAL0886 REV NO: V.4B DATE: MAR/02/2013 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201006684 AA4040ZGS Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) SPEC NO: DSAL0886 REV NO: V.4B DATE: MAR/02/2013 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201006684 PACKING & LABEL SPECIFICATIONS AA4040ZGS SPEC NO: DSAL0886 REV NO: V.4B DATE: MAR/02/2013 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201006684