SURFACE MOUNT DISPLAY Part Number: ACDC02-41SGWA-F01 Super Bright Green Features Description z 0.2 inch digit height. The Super Bright Green source color devices are made with z Low current operation. Gallium Phosphide Green Light Emitting Diode. z Excellent character appearance. z Mechanically rugged. z Package :300pcs / reel. z Gray face, white segment. z Moisture sensitivity level : level 2a. z RoHS compliant. Package Dimensions& Internal Circuit Diagram Green Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 3.The gap between the reflector and PCB shall not exceed 0.25mm. SPEC NO: DSAG0228 REV NO: V.10A DATE: DEC/28/2015 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: M.Liu ERP: 1352000287 Selection Guide Iv (ucd) [1] @ 10mA Part No. Emitting Color (Material) Lens Type Description Min. Typ. 1400 3900 Common Cathode, Rt. ACDC02-41SGWA-F01 Super Bright Green (GaP) White Diffused Hand Decimal. *560 *1400 Notes: 1. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. Max. Units Test Conditions λpeak Peak Wavelength Super Bright Green 565 nm IF=10mA λD [1] Dominant Wavelength Super Bright Green 568 nm IF=10mA Δλ1/2 Spectral Line Half-width Super Bright Green 30 nm IF=10mA C Capacitance Super Bright Green 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Green 2 2.5 V IF=10mA IR Reverse Current Super Bright Green 10 uA VR=5V Notes: 1. Wavelength: + / -1nm. 2. Forward Voltage: + / -0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 62.5 mW DC Forward Current 25 mA Peak Forward Current [1] 140 mA Reverse Voltage 5 V Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAG0228 REV NO: V.10A DATE: DEC/28/2015 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: M.Liu ERP: 1352000287 Super Bright Green ACDC02-41SGWA-F01 SPEC NO: DSAG0228 REV NO: V.10A DATE: DEC/28/2015 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: M.Liu ERP: 1352000287 ACDC02-41SGWA-F01 Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.15) Tape Specifications (Units : mm) SPEC NO: DSAG0228 REV NO: V.10A DATE: DEC/28/2015 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: M.Liu ERP: 1352000287 PACKING & LABEL SPECIFICATIONS ACDC02-41SGWA-F01 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAG0228 REV NO: V.10A DATE: DEC/28/2015 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: M.Liu ERP: 1352000287