INFRARED EMITTING DIODE Part Number: AM2520F3C03 Features Description z Subminiature package. F3 Made with Gallium Arsenide Infrared Emitting diodes. z Mechanically and spectrally matched to the phototransistor. z Gull wing lead. z Long life - solid state reliability. z Low package profile. z Package : 1000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 5. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAB2262 REV NO: V.10A DATE: SEP/01/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1202000467 Selection Guide Po (mW/sr) [2] Po (mW/sr) [2] Viewing @ 20mA @ 50mA Angle [1] Part No. Emitting Color (Material) Lens Type Min. Typ. Min. Typ. 2θ1/2 5 10 10 20 AM2520F3C03 Infrared (GaAs) Water Clear 20° *3 *8 *8 *16 Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity / luminous flux: +/-15%. * Radiant intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Parameter Emitting Color Symbol Typ. Max. Units Test Conditions Forward Voltage [1] F3 VF 1.2 1.6 V IF=20mA Reverse Current F3 IR 10 uA VR = 5V Capacitance F3 C 90 pF VF=0V;f=1MHz Peak Spectral Wavelength F3 λP 940 nm IF=20mA Spectral Bandwidth F3 Δλ1/2 50 nm IF=20mA Notes: 1.Forward Voltage: +/-0.1V. 2.Wavelength value is traceable to CIE127-2007 standards. 3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Symbol Values Units Power dissipation PD 80 mW F 50 mA DC Forward Current I Peak Forward Current [1] iFS 1.2 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 °C Storage Temperature TSTG -40 To +85 °C Notes: 1. 1/100 Duty Cycle, 10μs Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAB2262 REV NO: V.10A DATE: SEP/01/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1202000467 AM2520F3C03 SPEC NO: DSAB2262 REV NO: V.10A DATE: SEP/01/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1202000467 AM2520F3C03 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAB2262 REV NO: V.10A DATE: SEP/01/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1202000467 PACKING & LABEL SPECIFICATIONS AM2520F3C03 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAB2262 REV NO: V.10A DATE: SEP/01/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1202000467