1.6x0.6mm RIGHT ANGLE SMD CHIP LED LAMP Part Number: APA1606MGC Mega Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 1.6mmx1.2mmx0.6mm right angle SMD LED,0.6mm z The Mega Green source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode. thickness. z Electrostatic discharge and power surge could damage z Low power consumption. the LEDs. z Wide viewing angle. z It is recommended to use a wrist band or anti- z Ideal for backlight and indicator. z Package :2000pcs / reel. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be z Moisture sensitivity level : level 3. electrically grounded. z Tinned pads for improved solderability. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAH3726 REV NO: V.4B DATE: AUG/01/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203000455 Selection Guide Iv (mcd) [2] V iewing @ 20mA Angle [1] Part No. Emitting Color (Material) Lens Type Min. Typ. 2θ1/2 APA1606MGC Mega Green (AlGaInP) Water Clear 40 60 110° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Mega Green 574 nm IF=20mA λD [1] Dominant Wavelength Mega Green 570 nm IF=20mA Δλ1/2 Spectral Line Half-width Mega Green 26 nm IF=20mA C Capacitance Mega Green 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Mega Green 2.1 2.5 V IF=20mA IR Reverse Current Mega Green 10 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Mega Green Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAH3726 REV NO: V.4B DATE: AUG/01/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203000455 Mega Green APA1606MGC SPEC NO: DSAH3726 REV NO: V.4B DATE: AUG/01/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203000455 APA1606MGC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) SPEC NO: DSAH3726 REV NO: V.4B DATE: AUG/01/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203000455 PACKING & LABEL SPECIFICATIONS APA1606MGC Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAH3726 REV NO: V.4B DATE: AUG/01/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203000455