3.0x2.5mm SURFACE MOUNT LED LAMP Part Number: APBL3025EYC-F01 High Efficiency Red Yellow Features Descriptions z 3.0mmx2.5mm SMT LED, 1.4mm thickness. z The High Efficiency Red source color devices are made z Low power consumption. with Gallium Arsenide Phosphide on Gallium Phosphide z Wide viewing angle. Orange Light Emitting Diode. z Ideal for back light and indicator. z The Yellow source color devices are made with Gallium z Inner lens type. Arsenide Phosphide on Gallium Phosphide Yellow Light z Moisture sensitivity level : level 3. Emitting Diode. z Package : 2000pcs / reel. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAF1330 REV NO: V.8A DATE: MAY/03/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000886 Selection Guide Iv (mcd) [2] Viewing @ 20mA Angle [1] Part No. Dice Lens Type Min. Typ. 2θ1/2 12 20 High Efficiency Red (GaAsP/GaP) *8 *15 APBL3025EYC-F01 Water Clear 100° 5 15 Yellow (GaAsP/GaP) *5 *15 Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. Units Test Conditions High Efficiency Red 627 λpeak Peak Wavelength nm IF=20mA Yellow 590 High Efficiency Red 617 λD [1] Dominant Wavelength nm IF=20mA Yellow 588 High Efficiency Red 45 Δλ1/2 Spectral Line Half-width nm IF=20mA Yellow 35 High Efficiency Red 15 C Capacitance pF VF=0V;f=1MHz Yellow 20 High Efficiency Red 2 2.5 VF [2] Forward Voltage F=20mA V I Yellow 2.1 2.5 High Efficiency Red 10 IR Reverse Current uA VR = 5V Yellow 10 Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter High Efficiency Red Yellow Units Power dissipation 75 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 160 140 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAF1330 REV NO: V.8A DATE: MAY/03/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000886 APBL3025EYC-F01 High Efficiency Red SPEC NO: DSAF1330 REV NO: V.8A DATE: MAY/03/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000886 Yellow SPEC NO: DSAF1330 REV NO: V.8A DATE: MAY/03/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000886 APBL3025EYC-F01 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) SPEC NO: DSAF1330 REV NO: V.8A DATE: MAY/03/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000886 PACKING & LABEL SPECIFICATIONS APBL3025EYC-F01 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF1330 REV NO: V.8A DATE: MAY/03/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000886