KINGBRIGHT APT1608QR51F/D-AMT

1.6X0.8mm SMD CHIP LED LAMP Part Number: APT1608QR51F/D-AMT Cyan ATTENTION OBSERVE PRECAUTIONS FOR HANDLING Descriptions ELECTROSTATIC DISCHARGE z The source color devices are made with InGaN Light SENSITIVE Emitting Diode. DEVICES z Electrostatic discharge and power surge could damage the LEDs. Features z It is recommended to use a wrist band or anti- z High reliability LED package. electrostatic glove when handling the LEDs. z 1.6mmX0.8mm SMT LED, 0.75mm thickness. z All devices, equipments and machineries must be z Low power consumption. electrically grounded. z Wide viewing angle. Applications z Ideal for backlight and indicator. z Traffic signaling. z Package: 2000pcs / reel . z Backlighting (illuminated advertising , general lighting). z Moisture sensitivity level : level 3. z Interior and exterior automotive lighting. z RoHS compliant. z Substitution of micro incandescent lamps. z Reading lamps. z Signal and symbol luminaire for orientation. z Marker lights (e.g. Steps, exit ways, etc). z Decorative and entertainment lighting. Package Dimensions z Indoor and outdoor commercial and residential architectural lighting. Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL4281 REV NO: V.3B DATE: OCT/23/2014 PAGE: 1 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP:1203012233 Selection Guide Iv (mcd) [2] Viewing @ 20mA Angle [1] Part No. Dice Lens Type Code. Min. Max. 2θ1/2 N 120 200 APT1608QR51F/D-AMT Cyan (InGaN) Yellow Fluorescent P 200 300 120° Q 300 400 Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at Ta=25°C Parameter Symbol Value Unit Power dissipation PD 80 mW Reverse Voltage VR 5 V Junction temperature TJ 115 °C Operating Temperature Top -40 To +100 °C Storage Temperature Tstg -40 To +110 °C DC Forward Current[1] IF 20 mA Peak Forward Current [2] IFM 150 mA Electrostatic Discharge Threshold (HBM) 250 V Thermal Resistance (Junction/ambient) [1] Rth j-a 530 °C/W Notes: 2 1. Rth(j-a) Results from mounting on PC board FR4 (pad size≥16 mm per pad), 2. 1/10 Duty Cycle, 0.1ms Pulse Width. Electrical / Optical Characteristics at Ta=25°C Parameter Symbol Value Unit Chromaticity coordinate X acc.to CIE1931 X [1] 0.19 IF=20mA [Typ.] Chromaticity coordinate Y acc.to CIE1931 Y [1] 0.41 IF=20mA [Typ.] Forward Voltage IF=20mA [Min.] - Forward Voltage IF=20mA [Typ.] VF [2] 3.3 V Forward Voltage IF=20mA [Max.] 4.0 Reverse Current (VR = 5V) [Max.] IR 50 uA Temperature coefficient of VF TCV -2.4 mV/° C IF=20mA, -10° C≤ T≤100° C [Typ.] Temperature coefficient of X -3 TCX -0.13 10 /° C IF=20mA, -10° C≤ T≤100° C [Typ.] Temperature coefficient of Y -3 TCy -0.11 10 /° C IF=20mA, -10° C≤ T≤100° C [Typ.] Notes: 1.Measurement tolerance of the chromaticity coordinates is ± 0.01. 2.Forward Voltage: +/-0.1V. 3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. SPEC NO: DSAL4281 REV NO: V.3B DATE: OCT/23/2014 PAGE: 2 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP:1203012233 Cyan APT1608QR51F/D-AMT SPEC NO: DSAL4281 REV NO: V.3B DATE: OCT/23/2014 PAGE: 3 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP:1203012233 APT1608QR51F/D-AMT 0.50 0.49 0.48 0.47 0.46 B6 B61 0.45 0.44 0.43 B5 B51 0.42 0.41 0.40 B4 B41 0.39 0.38 0.37 B3 B31 0.36 0.35 0.34 0.14 0.15 0.16 0.17 0.18 0.19 0.20 0.21 0.22 0.23 0.24 B3 B31 X 0.1565 0.1795 0.1850 0.1630 X 0.1795 0.1850 0.2070 0.2025 Y 0.3500 0.3500 0.3800 0.3800 Y 0.3500 0.3800 0.3800 0.3500 B4 B41 X 0.1850 0.1630 0.1680 0.1900 X 0.1850 0.2070 0.2120 0.1900 Y 0.3800 0.3800 0.4100 0.4100 Y 0.3800 0.3800 0.4100 0.4100 B5 B51 X 0.1680 0.1900 0.1970 0.1750 X 0.2120 0.1900 0.1970 0.2190 Y 0.4100 0.4100 0.4400 0.4400 Y 0.4100 0.4100 0.4400 0.4400 B6 B61 X 0.1970 0.1750 0.1810 0.2030 X 0.2190 0.1970 0.2030 0.2250 Y 0.4400 0.4400 0.4700 0.4700 Y 0.4400 0.4400 0.4700 0.4700 Notes: Shipment may contain more than one chromaticity regions. Orders for single chromaticity region are generally not accepted. Measurement tolerance of the chromaticity coordinates is ±0.01. SPEC NO: DSAL4281 REV NO: V.3B DATE: OCT/23/2014 PAGE: 4 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP:1203012233 APT1608QR51F/D-AMT Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications Reel Dimension (Units : mm) SPEC NO: DSAL4281 REV NO: V.3B DATE: OCT/23/2014 PAGE: 5 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP:1203012233 PACKING & LABEL SPECIFICATIONS APT1608QR51F/D-AMT Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL4281 REV NO: V.3B DATE: OCT/23/2014 PAGE: 6 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP:1203012233 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below Lot Tolerance Percent Defective (LTPD) : 10% Test Times / Number of No. Test Item Standards Test Condition Cycles Damaged 1 Continuous operating test - Ta =25°C ,IF = maximum rated current* 1,000 h 0 / 22 EIAJ ED- 2 High Temp. operating test Ta = 100°C IF = derated current at 100°C 1,000 h 0 / 22 4701/100(101) 3 Low Temp. operating test - Ta = -40°C, IF = maximum rated current* 1,000 h 0 / 22 EIAJ ED- 4 High temp. storage test Ta = maximum rated storage temperature 1,000 h 0 / 22 4701/100(201) EIAJ ED- 5 Low temp. storage test Ta = -40°C 1,000 h 0 / 22 4701/100(202) EIAJ ED- 6 High temp. & humidity storage test Ta = 60°C, RH = 90% 1,000 h 0 / 22 4701/100(103) EIAJ ED- Ta = 60°C, RH = 90% 7 High temp. & humidity operating test 1,000 h 0 / 22 4701/100(102) IF = derated current at 60°C Moisture soak : 30°C,70% RH, 72h EIAJ ED- 8 Soldering reliability test Preheat : 150~180°C(120s max.) 2 time 0 / 18 4701/100(301) Soldering temp : 260°C(10s) Ta = -40°C(15min) ~ 100°C(15min) 9 Thermal shock operating test - 1,000 cycles 0 / 22 IF = derated current at 100°C 10 Thermal shock test - Ta = -40°C(15min) ~ 100°C(15min) 1,000 cycles 0 / 22 EIAJ ED- Once each 11 Electric Static Discharge (ESD) C = 100pF , R2 = 1.5KΩ V = 250V 0 / 22 4701/100(304) Polarity a = 196m/s² , f = 100~2KHz , 12 Vibration test - 4 times 0 / 22 t = 48min for all xyz axes * : Refer to forward current vs. derating curve diagram Failure Criteria Items Symbols Conditions Failure Criteria luminous Intensity lv IF = 20mA Testing Min. Value