KINGBRIGHT APTB1615SYKQBDW

1.6x1.5mm BI-COLOR SMD CHIP LED LAMP Part Number: APTB1615SYKQBDW ATTENTION OBSERVE PRECAUTIONS Super Bright Yellow FOR HANDLING Blue ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 1.6mmx1.5mm SMD LED, 0.7mm thickness. z The Super Bright Yellow device is made with AlGaInP z Low power consumption. (on GaAs substrate) light emitting diode chip. z Wide viewing angle. z The Blue source color devices are made with InGaN z Ideal for backlight and indicator. Light Emitting Diode. z Package : 2000pcs / reel. z Electrostatic discharge and power surge could damage z Moisture sensitivity level : level 3. the LEDs. z RoHS compliant. z It is recommended to use a wrist band or anti- electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded Package Dimensions Yellow Blue Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAK4185 REV NO: V.3B DATE: APR/14/2016 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203009724 Selection Guide Iv (mcd) [2] Viewing @ 20mA Angle [1] Part No. Emitting Color (Material) Lens Type Min. Typ. 2θ1/2 Super Bright Yellow (AlGaInP) 80 120 APTB1615SYKQBDW White Diffused 120° Blue (InGaN) 20 50 Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. Max. Units Test Conditions Super Bright Yellow 590 λpeak Peak Wavelength nm IF=20mA Blue 460 Super Bright Yellow 590 λD [1] Dominant Wavelength nm IF=20mA Blue 465 Super Bright Yellow 20 Δλ1/2 Spectral Line Half-width nm IF=20mA Blue 25 Super Bright Yellow 20 C Capacitance pF VF=0V;f=1MHz Blue 100 Super Bright Yellow 2 2.5 VF [2] Forward Voltage V IF=20mA Blue 3.3 4 Super Bright Yellow 10 IR Reverse Current uA VR = 5V Blue 50 Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Yellow Blue Units Power dissipation 75 120 mW DC Forward Current 30 30 mA Peak Forward Current [1] 175 150 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAK4185 REV NO: V.3B DATE: APR/14/2016 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203009724 APTB1615SYKQBDW Super Bright Yellow SPEC NO: DSAK4185 REV NO: V.3B DATE: APR/14/2016 PAGE: 3 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203009724 Blue SPEC NO: DSAK4185 REV NO: V.3B DATE: APR/14/2016 PAGE: 4 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203009724 APTB1615SYKQBDW Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) SPEC NO: DSAK4185 REV NO: V.3B DATE: APR/14/2016 PAGE: 5 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203009724 PACKING & LABEL SPECIFICATIONS APTB1615SYKQBDW Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAK4185 REV NO: V.3B DATE: APR/14/2016 PAGE: 6 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203009724