CC25-12YWA 6.2 mm (0.25 inch) Four Digit Numeric Display DESCRIPTION PACKAGE DIMENSIONS z The Yellow source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Yellow Light Emitting Diode FEATURES z 0.25 inch digit height z Low current operation z Excellent character appearance z Easy mounting on P.C. boards or sockets z Categorized for luminous intensity z Mechanically rugged z Standard: gray face, white segment z RoHS compliant APPLICATIONS z Home and smart appliances z Display time and digital combination z Industrial and instrumental applications z Numeric status Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SELECTION GUIDE [1] Iv (ucd) @ 10mA Emitting Color Part Number Lens Type Description (Material) Min. Typ. 3600 6800 CC25-12YWA ■ Yellow (GaAsP/GaP) White Diffused Common Cathode *1400 *2400 Notes: 1. Luminous intensity / luminous flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Page 1 / 5 © 2018 Kingbright. All Rights Reserved. Spec No: DSAP4734 / 1304000143 Rev No: V.1A Date: 05/07/2018 CC25-12YWA ELECTRICAL / OPTICAL CHARACTERISTICS at T =25°C A Value Parameter Symbol Emitting Color Unit Typ. Max. Wavelength at Peak Emission I = 10mA λ Yellow 590 - nm F peak [1] Dominant Wavelength I = 10mA λ Yellow 588 - nm F dom Spectral Bandwidth at 50% Φ REL MAX Δλ Yellow 35 - nm I = 10mA F Capacitance C Yellow 20 - pF Forward Voltage I = 20mA (D7,L) 1.95 2.4 F [2] Forward Voltage I = 10mA(Dig1'8,'Dig2'8', V Yellow V F F Dig3'8',Dig4'8',D1,D2,D3,D4,D5,D6,D8) 1.95 2.4 Reverse Current (V = 5V) (Per chip) I Yellow - 10 uA R R Notes: 1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. ) 2. Forward voltage: ±0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at T =25°C A Parameter Symbol Value Unit Power Dissipation (Per chip) P 75 mW D Reverse Voltage (Per chip) V 5 V R Junction Temperature T 110 °C j Operating Temperature T -40 to +85 °C op Storage Temperature T -40 to +85 °C stg Forward Voltage I = 20mA (D7,L) 60 F Forward Voltage I = 10mA(Dig1'8,'Dig2'8', I mA F F Dig3'8',Dig4'8',D1,D2,D3,D4,D5,D6,D8) 30 Peak Forward Current I = 20mA (D7,L) 280 F [1] Peak Forward Current I = 10mA(Dig1'8,'Dig2'8', I mA F FM Dig3'8',Dig4'8',D1,D2,D3,D4,D5,D6,D8) 140 Electrostatic Discharge Threshold (HBM) 8000 V - [2] Lead Solder Temperature 260°C For 3-5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. Page 2 / 5 © 2018 Kingbright. All Rights Reserved. Spec No: DSAP4734 / 1304000143 Rev No: V.1A Date: 05/07/2018 CC25-12YWA TECHNICAL DATA RELATIVE INTENSITY vs. WAVELENGTH Yellow 100% T = 25 °C a 80% 60% 40% 20% 0% 350 400 450 500 550 600 650 700 750 800 Wavelength (nm) YELLOW (D7,L) Forward Current Derating Curve Forward Current vs. Luminous Intensity vs. Luminous Intensity vs. Forward Voltage Forward Current Ambient Temperature 60 10.0 100 2.5 T = 25 °C a T = 25 °C a 50 8.0 80 2.0 40 6.0 60 1.5 30 4.0 40 1.0 20 2.0 20 0.5 10 0 0.0 0 0.0 1.93 1.94 1.95 1.96 1.97 1.98 0 2040 6080 100 -40 -20 0 20 406080 100 -40 -20 0 204060 80 100 Forward voltage (V) Forward current (mA) Ambient temperature (°C) Ambient temperature (°C) YELLOW (DIG1’8,’DIG2’8’,DIG3’8’,DIG4’8’,D1,D2,D3,D4,D5,D6,D8) Forward Current vs. Luminous Intensity vs. Forward Current Derating Curve Luminous Intensity vs. Forward Voltage Forward Current Ambient Temperature 20 5.0 50 2.5 T = 25 °C a T = 25 °C a 16 4.0 40 2.0 12 3.0 30 1.5 8 2.0 20 1.0 4 1.0 10 0.5 0 0.0 0 0.0 1.93 1.94 1.95 1.96 1.97 1.98 0 1020 3040 50 -40 -20 0 20 406080 100 -40 -20 0 204060 80 100 Forward voltage (V) Forward current (mA) Ambient temperature (°C) Ambient temperature (°C) Page 3 / 5 © 2018 Kingbright. All Rights Reserved. Spec No: DSAP4734 / 1304000143 Rev No: V.1A Date: 05/07/2018 Forward current (mA) Forward current (mA) Relative Intensity (a. u.) Luminous intensity normalised at Luminous intensity normalised at 10 mA 10 mA Permissible forward current (mA) Permissible forward current (mA) Luminous intensity normalised at Luminous intensity normalised at Ta = 25 °C Ta = 25 °C CC25-12YWA RECOMMENDED WAVE SOLDERING PROFILE Soldering General Notes 1. Through-hole displays are incompatible with reflow soldering. 2. If components will undergo multiple soldering processes, or other processes where the components may be subjected to intense heat, please check with Kingbright for compatibility. CLEANING 1. Mild "no-clean" fluxes are recommended for use in soldering. 2. If cleaning is required, Kingbright recommends to wash components with water only. Do not use harsh organic solvents for cleaning because they may damage the plastic parts . 3. The cleaning process should take place at room temperature and the devices should not be washed for more than one minute. 4. When water is used in the cleaning process, Immediately Notes: 1. Recommend pre-heat temperature of 105°C or less (as measured with a thermocouple remove excess moisture from the component with forced-air attached to the LED pins) prior to immersion in the solder wave with a maximum solder bath drying afterwards. temperature of 260°C 2. Peak wave soldering temperature between 245°C ~ 255°Cfor 3 sec (5 sec max). 3. Do not apply stress to the epoxy resin while the temperature is above 85°C. 4. Fixtures should not incur stress on the component when mounting and during soldering process. 5. SAC 305 solder alloy is recommended. 6. No more than one wave soldering pass. THROUGH HOLE DISPLAY MOUNTING METHOD Lead Forming 1. Do not bend the component leads by hand without proper tools. The leads should be bent by clinching the upper part of the lead firmly such that the bending force is not exerted on the plastic body. Installation 1. The installation process should not apply stress to the lead terminals. 2. When inserting for assembly, ensure the terminal pitch matches the substrate board's hole pitch to prevent spreading or pinching the lead terminals. (Fig.1) 3. The component shall be placed at least 5mm from edge of PCB to avoid damage caused excessive heat during wave soldering.(Fig.2) CIRCUIT DESIGN NOTES 1. Protective current-limiting resistors may be necessary to operate the LEDs within the specified range. 2. LEDs mounted in parallel should each be placed in series with its own current-limiting resistor.(Fig.3) 3. The driving circuit should be designed to protect the LED against reverse voltages and transient voltage spikes when the circuit is powered up or shut down. 4. The safe operating current should be chosen after considering the maximum ambient temperature of the operating environment. 5. Prolonged reverse bias should be avoided, as it could cause metal migration, leading to an increase in leakage current or causing a short circuit. Page 4 / 5 © 2018 Kingbright. All Rights Reserved. Spec No: DSAP4734 / 1304000143 Rev No: V.1A Date: 05/07/2018 CC25-12YWA PACKING & LABEL SPECIFICATIONS PRECAUTIONARY NOTES 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. When any special process such as potting is required for LED assembly, please consult with Kingbright representative before proceeding. 7. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes Page 5 / 5 © 2018 Kingbright. All Rights Reserved. Spec No: DSAP4734 / 1304000143 Rev No: V.1A Date: 05/07/2018