KINGBRIGHT L7676CSEC/H

7.6mmX7.6mm SUPER FLUX LED LAMP Part Number: L-7676CSEC-H Hyper Orange Features Description z Super flux output. This devices are made with TS AlGaInP. z Design for high current operation. z Outstanding material efficiency. z Reliable and rugged. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAA4216 REV NO: V.20A DATE: JUN/11/2016 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1101010222 Kingbright Selection Guide Iv (mcd) [2] Φv (mlm) [2] Viewing @ 20mA @ 20mA Angl e [1] Part No. Emitting Color (Material) Lens Type Min. Typ. Typ. 2θ1/2 700 1300 L-7676CSEC-H Hyper Orange (AlGaInP) Water Clear *1200 70° *400 *800 Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%.LEDs are binned according to their Luminous intensity. 3. Drive current between 10mA and 30mA are recommended for long term performance. 4. Operation at current below 10mA is not recommended. * Luminous intensity/ luminous Flux value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. Max. Units Test Conditions λpeak Peak Wavelength Hyper Orange 635 nm IF=20mA λD [1] Dominant Wavelength Hyper Orange 625 nm IF=20mA Δλ1/2 Spectral Line Half-width Hyper Orange 25 nm IF=20mA C Capacitance Hyper Orange 27 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Orange 2.2 2.8 V IF=20mA IR Reverse Current Hyper Orange 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 84 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA Reverse Voltage 5 V Operating/Storage Temperature -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. 4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAA4216 REV NO: V.20A DATE: JUN/11/2016 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1101010222 Kingbright Hyper Orange L-7676CSEC-H SPEC NO: DSAA4216 REV NO: V.20A DATE: JUN/11/2016 PAGE: 3 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1101010222 Kingbright PACKING & LABEL SPECIFICATIONS L-7676CSEC-H Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes SPEC NO: DSAA4216 REV NO: V.20A DATE: JUN/11/2016 PAGE: 4 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1101010222 Kingbright SPEC NO: DSAA4216 REV NO: V.20A DATE: JUN/11/2016 PAGE: 5 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1101010222 Kingbright SPEC NO: DSAA4216 REV NO: V.20A DATE: JUN/11/2016 PAGE: 6 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1101010222 Kingbright