KINGBRIGHT WP154A4SUREQBFZGW

T-1 3/4 (5mm) FULL COLOR LED LAMP Part Number: WP154A4SUREQBFZGW ATTENTION OBSERVE PRECAUTIONS Hyper Red FOR HANDLING Blue ELECTROSTATIC Green DISCHARGE SENSITIVE DEVICES Features Descriptions z Uniform light output. z The Hyper Red source color devices are made with z Low power consumption. AlGaInP on GaAs substrate Light Emitting Diode. z Long life-solid state reliability. z The Blue source color devices are made with InGaN Light z RoHS compliant. Emitting Diode. z The Green source color devices are made with InGaN on Sapphire Light Emitting Diode. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or anti- electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAJ8688 REV NO: V.6A DATE: MAR/05/2015 PAGE: 1 OF 8 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101026911 Selection Guide Iv (mcd) [2] Viewing @ 20mA Angle [1] Part No. Dice Lens Type Min. Typ. 2θ1/2 400 1000 Hyper Red (AlGaInP) *120 *250 300 500 WP154A4SUREQBFZGW Blue (InGaN) White Diffused 60° *300 *500 600 1300 Green (InGaN) *600 *1300 Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. Units Test Conditions Hyper Red 645 λpeak Peak Wavelength Blue 460 nm IF=20mA Green 515 Hyper Red 630 λD [1] Dominant Wavelength Blue 465 nm IF=20mA Green 525 Hyper Red 25 Δλ1/2 Spectral Line Half-width Blue 25 nm IF=20mA Green 30 Hyper Red 45 C Capacitance Blue 100 pF VF=0V;f=1MHz Green 45 Hyper Red 1.9 2.5 VF [2] Forward Voltage Blue 3.3 4 V IF=20mA Green 3.3 4.1 Hyper Red 10 IR Reverse Current Blue 50 uA VR=5V Green 50 Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Blue Green Units Power dissipation 75 120 102.5 mW DC Forward Current 30 30 25 mA Peak Forward Current [1] 200 150 150 mA Reverse Voltage 5 V Operating/Storage Temperature -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. SPEC NO: DSAJ8688 REV NO: V.6A DATE: MAR/05/2015 PAGE: 2 OF 8 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101026911 WP154A4SUREQBFZGW Hyper Red SPEC NO: DSAJ8688 REV NO: V.6A DATE: MAR/05/2015 PAGE: 3 OF 8 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101026911 Blue SPEC NO: DSAJ8688 REV NO: V.6A DATE: MAR/05/2015 PAGE: 4 OF 8 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101026911 Green SPEC NO: DSAJ8688 REV NO: V.6A DATE: MAR/05/2015 PAGE: 5 OF 8 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101026911 PACKING & LABEL SPECIFICATIONS WP154A4SUREQBFZGW Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAJ8688 REV NO: V.6A DATE: MAR/05/2015 PAGE: 6 OF 8 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101026911 SPEC NO: DSAJ8688 REV NO: V.6A DATE: MAR/05/2015 PAGE: 7 OF 8 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101026911 SPEC NO: DSAJ8688 REV NO: V.6A DATE: MAR/05/2015 PAGE: 8 OF 8 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101026911