KINGBRIGHT WP7679C1QBC/D

SUPER FLUX LED LAMP Part Number: WP7679C1QBC/D Technical Data ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Descriptions  Electrostatic discharge and power surge could damage the LEDs.  It is recommended to use a wrist band or anti- electrostatic glove when handling the LEDs.  All devices, equipments and machineries must be electrically grounded. Features: Benefits: *High Iuminance output. *Outstanding Material Efficiency. *Design for high current operation. *Electricity savings. *Uniform color. *Low power consumption. *Maintenance savings. *Low thermal resistance. *Reliable and Rugged. *Low profile. *Packaged in tubes for use with automatic insertion equipment. Typical Applications: *Soldering methods: wave soldering. *RoHS Compliant. *Automotive Exterior Lighting. *Electronic Signs and Signals. *Specialty Lighting. SPEC NO: DSAH3826 REV NO: V.6B DATE: SEP/06/2014 PAGE: 1 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101017708 Outline Drawings Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. Absolute Maximum Ratings at TA=25°C PARAMETER QB-D UNITS DC Forward Current 30 mA Power dissipation 126 mW Reverse Voltage 5 V Operating Temperature -40 To +85 °C Storage Temperature -55 To +85 °C Lead Solder Temperature[1] 260°C For 5 Seconds 1.1.5mm[0.06inch]below seating plane. NO Reflow soldering . SPEC NO: DSAH3826 REV NO: V.6B DATE: SEP/06/2014 PAGE: 2 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101017708 Selection Guide Iv(cd)[1] Фv(lm)[1] Viewing Angle[2] Part No. LED COLOR @30mA @30mA 2θ1/2 Min. Typ. Typ. Typ. WP7679C1QBC/D Blue (InGaN) 0.36 0.8 0.5 70° Notes: 1.Luminous intensity is measured with an integrating sphere after the device has stabilized; Luminous Intensity / luminous flux: +/-15%. 2.θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 3.Luminous Intensity / luminous flux value is traceable to the CIE127-2007 compliant national standards Optical Characteristics at TA=25°C IF=30mA Rθj-a=200°C/W PEAK DOMINANT[1] SPECTRAL LINE DEVICE WAVELENGTH WAVELENGTH WAVELENGTH λPEAK (nm) λDOM (nm) Δλ1/2(nm) TYPE TYP. TYP. TYP. QB-D 460 465 25 Notes: 1.The dominant wavelength is derived from the CIE Chromaticity Diagram and represents the perceived color of the device; Wavelength: +/-1nm. 2.Wavelength value is traceable to the CIE127-2007 compliant national standards. Electrical Characteristics at TA=25°C FORWARD VOLTAGE REVERSE CURRENT CAPACITANCE THERMAL [1] IR (uA) C (pF) RESISTANCE VF (VOLTS) DEVICE @ @ Rθj -pin @ VR=5V VF=0V F=1MHZ °C/W IF=30mA TYPE TYP. MAX. MAX. TYP. TYP. QB-D 3.5 4.2 50 100 180 Note: 1. Forward Voltage: +/-0.1V. 2. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. SPEC NO: DSAH3826 REV NO: V.6B DATE: SEP/06/2014 PAGE: 3 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101017708 Figures SPEC NO: DSAH3826 REV NO: V.6B DATE: SEP/06/2014 PAGE: 4 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101017708 PACKING & LABEL SPECIFICATIONS WP7679C1QBC/D Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAH3826 REV NO: V.6B DATE: SEP/06/2014 PAGE: 5 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101017708 SPEC NO: DSAH3826 REV NO: V.6B DATE: SEP/06/2014 PAGE: 6 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101017708 SPEC NO: DSAH3826 REV NO: V.6B DATE: SEP/06/2014 PAGE: 7 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101017708