DALI Bus Power Supply DLP-04 series �/&*1#6�� �/&*1#6&� � � 05 10 ■ �������� ■ ������������ ‧������������������������������������ ‧/�&%5�� ‧����������������� ������!� ‧/�&%5�� *����������� ‧"�������� �##VAC ���!� ����� $�� � ������� ‧%������������� Ⅱ ‧’� ���� ����� �����������(#)�"�����&� ‧*����������+�������������,��������!� ‧������!-�$���������������� ‧������&./$������������������������ ‧%����������/%’����0�1���2)���3�������� ‧3##4$�������-���1������ ‧�������������� ■ ����������� 0��/�&%*����������/&*1#6 ��������������������!��$$��������������������,��������!�6#��$�� /�&%�������!�������/�&%��������� �����������������������������)0��1�#789#℃��������������� ��������!���!�����������:�����$������������) %������$����������-��$����������������������-�����������/�&%��������:)����������������$���������� ������������;���������������������������#?@��$-��������-�����!�3�A�����������1�������������������#)3�$>62�$�����������������) �)0��������������������������������������������-���������������$�����B�������)0��$�����B�����������-���1���$��������������������� .?�����������) File Name:DLP-04-SPEC 2018-01-09 DALI Bus Power Supply DLP-04 series Block Diagram fosc: 100KHz RECTIFIERS RECTIFIERS POWER +V EMI I/P & & SWITCHING FILTER -V FILTER FILTER DETECTION CIRCUIT O.L.P. CONTROL O.V.P. Derating Curve Output Derating VS Input Voltage 100 100 90 80 80 70 60 60 40 50 20 40 -20 0102030405060 70(VERTICAL) 90 100 115 120 140 160 180 200 220 240 264 AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (VAC) File Name:DLP-04-SPEC 2018-01-09 LOAD (%) LOAD (%) 35 DALI Bus Power Supply DLP-04 series ※ R-Type Case No.985A Unit:mm (Unit:mm,tolerance±0.5mm) 58.4 35 54.5 2 1 4 3 ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15 Terminal Pin No. Assignment Pin No. Assignment Pin No. Assignment 1 3 AC/L DA- 2 DA+ 4 AC/N File Name:DLP-04-SPEC 2018-01-09 90 63.65 45.15 DALI Bus Power Supply DLP-04 series ※ L-Type Case No.PLM-25 Unit:mm 145 4.5 ψ3.5 1 2 2 1 TB3 TB3 TB4 4.5 NOTE: The input and output line for using UL1015 18AWG*2C is suggested Terminal Pin No. Assignment (TB3) : Terminal Pin No. Assignment (TB4) : SWITCHLAB MWX201-75002EB(GRAY) SWITCHLAB MWX201-75002B(BLUE) Pin No. Assignment Pin No. Assignment 11 DA- AC/N 22 AC/L DA+ File Name:DLP-04-SPEC 2018-01-09 4.5 3.5 4.5 22 38 DALI Bus Power Supply DLP-04 series Installation Manual N L L L L L L L L L L L L L L L ’ & ’ &’ DLP-04 /�8 /�1 &.//�����! DC &.//�����! /� &./ &./ ,�0*�0 ,�0*�0 /����� /����� /� /� /� /� /�&% 5�� /�&% /�&% /�&%1C� /�&%1C� /�&%?����� ◎Cautions ‧Central DALI power supply rated at 240mA(DALI standard allows max.250mA). ‧The controls interface of a DALI ballast normally source<2mA,with 64 individualam ddresses this will source 128A) The remaining 112mA can be used to power other DALI controls without an internal power supply such as the DALI GC and DALI SC. ‧DALI signals are not SELV.Therefore the same procedures should be applied as working with mains voltage. ‧Individual DALI circuits must not exceed 240mA. ‧The maximum cable length of the DALI signal wires must not exceed 300m or drop more than 2V on the signal line voltage. File Name:DLP-04-SPEC 2018-01-09 DALI DALI B Bus us Power Power S Supply upply DLP-04 series System start-up timing 1.After external power-on ,timing of a bus power supply shall be as shown in table 1. 2.A receiver shall be ready to receive frames within the maximum receiver start-up time specified in Table 1. 3.A transmitter or a multi-master transmitter shall not start transmissions earlier than the transmitter start-up time specified in Table 1. ◎ Table 1 – Start-up timing Minimum Typical Maximum Condition Bus power supply start-up time 250ms Guaranteed Advanced bus power supply start-up time 400ms supply current a reached 400ms Integrated bus power supply start-up time b 5s Receiver start-up time for externally powered bus units, e 450ms after external power cycle Receiver start-up time for externally powered bus units, 100ms after bus power down d Receiver start-up time after bus power down U=10V 1200ms for bus powered bus units c Transmitter start-up time 110ms Multi-master transmitter start-up time 110ms a Applicable if other bus power supplies are allowed in the system b Applicable if no other bus power supplies are allowed in the system. c Not applicable for transmitters of bus units which cannot determine the bus state. d Idle state, bus voltage measured at the interface of the bus unit. e If an external power cycle occurred and the bus power is not available within 350 ms, the 100 ms timing is applicable. ◎ Shows an example of the system start-up timing 4 450ms Ns External 1 power supply 5 5 3 Off 2 4 3 100ms Idle 250ms Bus 110ms 6 110ms power supply OV Time 1200ms 1200ms 1 4 External power cycle Latest receiver start-up for externally powered unit 2 Latest bus power supply start-up 5 Latest receiver start-up for bus powered unit 3 6 Earliest transmitter start-up Bus power down File Name:DLP-04-SPEC 2018-01-09