MEAN WELL HBG-100P-48B

100W Constant Current Mode LED Driver HBG -100P series SELV (for DA Type only) ■ Features ■ Applications ‧ConstantCurrentmodeoutput ‧LEDbaylighting ‧CircularshapePCBtypedesign ‧LEDdownlighting ‧Built-inactivePFCfunction ‧LEDspotlighting ‧Functionoptions:outputadjustableviapotentiometer; ‧LEDmininglighting 3in1dimming;DALI ‧LEDstagelighting ‧Typicallifetime>50000hours ‧5yearswarranty ■ Description HBG-100Pseriesisa100WAC/DCPCBtypeLEDdriverfeaturingthecircularshapedesign. Itoperatesfrom90～305VACandoffersconstantcurrentoutputmodelswithdifferentrated voltagerangingbetween36Vand60V.Thankstothehighefficiencyupto91.5%,withthe fanlessdesign,theentireseriesisabletooperatefor-40℃~+45℃underfreeairconvection. HBG-100Pisequippedwithvariousfunctionoptions,suchasdimmingmethodology,soasto providetheoptimaldesignflexibilityforLEDlightingsystem. ■ ModelEncoding -36 HBG-100P A Functionoptions Ratedoutputvoltage(36/48/60V) PCBtype Ratedwattage Seriesname Type Function Note A Ioadjustablethroughbuilt-inpotentiometer. InStock B 3in1dimmingfunction(1~10Vdc,10VPWMsignalandresistance) InStock DA DALIcontroltechnology. InStock File Name:HBG-100P-SPEC 2018-05-04 100W Constant Current Mode LED Driver HBG -100P series SPECIFICATION MODEL HBG-100P-36 HBG-100P-48 HBG-100P-60 RATED CURRENT 2.7A 2A 1.6A RATED POWER 97.2W 96W 96W CONSTANT CURRENT REGION Note.2 21.6 ~ 36V 28.8 ~ 48V 36 ~ 60V OPEN CIRCUIT VOLTAGE(max.) 37V 49V 62V OUTPUT Adjustable for A-Type only (via built-in potentiometer) CURRENT ADJ. RANGE 1.62 ~ 2.7A 1.2 ~ 2A 1.0 ~ 1.6A CURRENT RIPPLE 5.0% max. @rated current ±5.0% CURRENT TOLERANCE SET UP TIME Note.4 2000ms / 115VAC 500ms / 230VAC 90 ~ 305VAC 127 ~ 431VDC VOLTAGE RANGE Note.3 (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE 47 ~ 63Hz PF≧0.96/115VAC, PF≧0.96/230VAC, PF≧0.94/277VAC@full load POWER FACTOR (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< 20%(@load≧60%/115VC,230VAC; @load≧75%/277VAC) TOTAL HARMONIC DISTORTION (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section) INPUT EFFICIENCY (Typ.) Note.5 91% 91% 91.5% AC CURRENT 1.1A / 115VAC 0.5A / 230VAC 0.45A / 277VAC INRUSH CURRENT(Typ.) COLD START 60A(twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 MAX. No. of PSUs on 16A 4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.75mA / 277VAC 95 ~ 108% OVER CURRENT Constant current limiting, recovers automatically after fault condition is removed PROTECTION 41 ~ 49V 54 ~ 63V 65 ~ 75V OVER VOLTAGE Shut down o/p voltage, re-power on to recovery OVER TEMPERATURE Shut down o/p voltage, re-power on to recovery Ta=-40 ~ +45℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) WORKING TEMP. 20 ~ 95% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 45℃) VIBRATION 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS UL8750,CSA C22.2 No.250.13-12; ENEC EN61347-1,EN61347-2-13,EN62384, GB19510.1,GB19510.14,EAC TP TC 004 approved DALI STANDARDS Compliance to IEC62386-101, 102, 207 for DA-Type only WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH EMC Compliance to EN55015, EN61000-3-2 Class C (@load ≧60%) ; EN61000-3-3, GB17743, GB17625.1,EAC TP TC 020 EMC EMISSION EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547,light industry level(surge immunity:Line-Earth:4KV,Line-Line:2KV),EAC TP TC 020 MTBF 346.8Khrs min. MIL-HDBK-217F (25℃) OTHERS DIMENSION Refer to mechanical specification 0.3Kg; 45pcs/14.5Kg/1.60CUFT PACKING 1.AllparametersNOTspeciallymentionedaremeasuredat230VACinput,ratedcurrentand25℃ofambienttemperature. NOTE 2.Pleasereferto"DRIVINGMETHODSOFLEDMODULE". 3.De-ratingmaybeneededunderlowinputvoltages.Pleasereferto“STATICCHARACTERISTIC”sectionsfordetails. 4.Lengthofsetuptimeismeasuredatfirstcoldstart.TurningON/OFFthepowersupplymayleadtoincreaseofthesetuptime. 5.TheDAtypepowersupplyislessefficientthanthetypicalefficiencyinspecificationby1%. 6.Thedriverisconsideredasacomponentthatwillbeoperatedincombinationwithfinalequipment.SinceEMCperformancewillbeaffectedbythe completeinstallation,thefinalequipmentmanufacturersmustre-qualifyEMCDirectiveonthecompleteinstallationagain. 7.Thisseriesmeetsthetypicallifeexpectancyof>50,000hoursofoperationwhenTaisabout45℃orless. 8.PleaserefertothewarrantystatementonMEANWELL'swebsiteathttp://www.meanwell.com 9.Theambienttemperaturederatingof3.5℃/1000mwithfanlessmodelsandof5℃/1000mwithfanmodelsforoperatingaltitudehigherthan2000m(6500ft). File Name:HBG-100P-SPEC 2018-05-04 100W Constant Current Mode LED Driver HBG -100P series BLOCK DIAGRAM fosc : 100KHz RECTIFIERS EMI FILTER POWER PFC +V I/P & & SWITCHING CIRCUIT -V RECTIFIERS FILTER O.C.P. O.T.P. O.L.P. DETECTION FG CIRCUIT PWM & PFC CONTROL O.V.P. DRIVING METHODS OF LED MODULE ※ This series works in constant current mode to directly drive the LEDs. In the constant current region, the highest voltage at the output of the driver 100 depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. Constant Current area 60 (min.) Hiccup Protection 50 100 Io(%) Typical output current normalized by rated current (%) File Name:HBG-100P-SPEC 2018-05-04 Vo(%) G G D S 100W Constant Current Mode LED Driver HBG -100P series DIMMING OPERATION BD1 SJTW 18AWG*3C AC/L(Brown) FS1 ACL AC/N(Blue) ACN FG (Green/Yellow) FG -V C5 -V(Black) L1 +V T1 HS1 SJTW 18AWG*2C Q2 L100 Q1 * DIM+ for B-Type C107 DA+ for DA-Type L3 * *DIM- for B-Type C106 DA- for DA-Type VR2 VR1 **DIM-(White) CN1 *DIM+(Blue) SVR1 UL2517 22AWG*2C ※ 3 in 1 dimming function (for B-Type) ‧Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1 ~ 10VDC, or 10V PWM signal or resistance. ‧Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. ‧Dimming source current from power supply: 100μA (typ.) ◎ Applying additive 1 ~ 10VDC 100% LED Strips 90% + +V + 80% 70% - - -V 60% DIM+ 50% + 40% Additive Voltage - 30% DIM- 20% 10% “DO NOT connect "DIM- to -V" 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage ◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): 100% LED Strips 90% + +V + 80% 70% - - -V 60% DIM+ 50% 40% Additive PWM signal 30% DIM- 20% 10% “DO NOT connect "DIM- to -V" 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input File Name:HBG-100P-SPEC 2018-05-04 +V(Red) Q101 HS2 ZNR1 Output current (%) Output current (%) LF1 C1 + 100W Constant Current Mode LED Driver HBG -100P series ◎ Applying additive resistance: 100% LED Strips + 90% + +V 80% - 70% - -V 60% DIM+ 50% Additive Resistance 40% DIM- 30% 20% “DO NOT connect "DIM- to -V" 10% 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for
synchronized
dimming
operation) Dimming input: Additive resistance Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Switch Adjuster Relay 10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Blue DIM+ Green/ White HBG-100P DIM- Yellow AC/L Black Brown V(-) B-Type Red LED Lighting Fixture V(+) AC/N Blue Using a switch and relay can turn ON/OFF the lighting fixture. ※ DALI Interface (primary side; for DA-Type) ‧Apply DALI signal between DA+ and DA-. ‧DALI protocol comprises 16 groups and 64 addresses. ‧First step is fixed at 8% of output. File Name:HBG-100P-SPEC 2018-05-04 Output current (%) 100W Constant Current Mode LED Driver HBG -100P series OUTPUT LOAD vs TEMPERATURE 100 230VAC 80 230VAC Input only 100VAC 60 50 40 20 -40 -25 -10 0 15 30 40 45 50 60 (HORIZONTAL) AMBIENT TEMPERATURE, Ta (℃) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Constant Current Mode 100 1 0.99 90 0.98 80 0.97 70 0.96 277V 0.95 60 230V 0.94 50 115V 0.93 40 0.92 0.91 90 100 125 135 145 155 165 175 180 200 230 305 50% 60% 70% 80% 90% 100% INPUT VOLTAGE (V) 60Hz LOAD ※De-rating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD HBG-100P series possess superior working efficiency that up to 91.5% can ※ 60V Model be reached in field applications. ※ 60V Model 25% 94 20% 92 90 15% 88 277V 86 277V 10% 230V 84 230V 82 115V 115V 5% 80 78 76 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 50% 60% 70% 80% 90% 100% LOAD LOAD File Name:HBG-100P-SPEC 2018-05-04 THD LOAD (%) LOAD (%) EFFICIENCY(%) PF G G G S D G D S 100W Constant Current Mode LED Driver HBG -100P series MECHANICAL SPECIFICATION Unit:mm ※ A-type 34 ψ24 1.6 300±20 BD1 SJTW 18AWG*3C AC/L(Brown) FS1 ACL AC/N(Blue) ACN FG (Green/Yellow) 200±20 -V FG C5 33.75 -V(Black) L1 +V ψ3.5 T1 HS1 SJTW 18AWG*2C Q2 L100 Q1 C107 L3 C106 Io.adj VR2 VR1 CN1 SVR1 ※ B/DA type 34 ψ24 1.6 300±20 BD1 SJTW 18AWG*3C AC/L(Brown) FS1 ACL AC/N(Blue) ACN FG (Green/Yellow) 200±20 FG -V C5 33.75 -V(Black) L1 ψ3.5 +V T1 HS1 SJTW 18AWG*2C Q2 L100 Q1 C107 L3 C106 300±20 VR2 VR1 *DIM+(Blue) CN1 **DIM-(White) SVR1 UL2517 22AWG*2C * DIM+ for B-Type DA+ for DA-Type * *DIM- for B-Type DA- for DA-Type File Name:HBG-100P-SPEC 2018-05-04 +V(Red) +V(Red) ψ104 ψ104 Q101 Q101 HS2 HS2 ZNR1 ZNR1 31 31 LF1 LF1 C1 C1 + +