MEAN WELL HRP-450-36

MEAN WELL HRP-450 SERIES 450 Watt Enclosed with Fan Power Supply 450W Single Output with PFC Function HRP-450 series Measures: 8.56 x 4.13 x 1.61” ■€ � �     �
  � ­  � €‚ƒƒƒ„ � „ � ƒ…ƒ � †ƒ‡ � „  �ˆ Bauart gepruft Sicherheit egelma ge od os be wac g www.tuv.com ID 2000000000 SPECIFICATION MODEL HRP-450-3.3 HRP-450-5 HRP-450-7.5 HRP-450-12 HRP-450-15 HRP-450-24 HRP-450-36 HRP-450-48 DC VOLTAGE 3.3V 5V 7.5V 12V 15V 24V 36V 48V RATED CURRENT 90A 90A 60A 37.5A 30A 18.8A 12.5A 9.5A CURRENT RANGE 0 ~ 90A 0 ~ 90A 0 ~ 60A 0 ~ 37.5A 0 ~ 30A 0 ~ 18.8A 0 ~ 12.5A 0 ~ 9.5A RATED POWER 297W 450W 450W 450W 450W 451.2W 450W 456W RIPPLE & NOISE (max.) Note.2 80mVp-p 80mVp-p 100mVp-p 120mVp-p 150mVp-p 150mVp-p 240mVp-p 240mVp-p OUTPUT VOLTAGE ADJ. RANGE 2.8 ~ 3.8V 4.3 ~ 5.8V 6.8 ~ 9V 10.2 ~ 13.8V 13.5 ~ 18V 21.6 ~ 28.8V 28.8 ~ 39.6V 40.8 ~ 55.2V VOLTAGE TOLERANCE Note.3 ±2.0% ±2.0% ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.3% ±0.3% ±0.2% ±0.2% ±0.2% LOAD REGULATION ±1.0% ±1.0% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME 1000ms, 100ms/230VAC 2500ms, 100ms/115VAC at full load HOLD UP TIME (Typ.) 16ms/230VAC 16ms/115VAC at full load VOLTAGE RANGE Note.5 85 ~ 264VAC 120 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/230VAC PF>0.99/115VAC at full load INPUT EFFICIENCY (Typ.) 80% 83% 86.5% 88% 89% 88% 89% 89.5% 5A/115VAC 2.4A/230VAC AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 35A/115VAC 70A/230VAC LEAKAGE CURRENT <1.5mA / 240VAC 105 ~ 135% rated output power OVERLOAD Protection type : Constant current limiting, recovers automatically after fault condition is removed 3.96 ~ 4.62V 6 ~ 7V 9.4 ~ 10.9V 14.4 ~ 16.8V 18.8 ~ 21.8V 30 ~ 34.8V 41.4 ~ 48.6V 57.6 ~ 67.2V PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down PSU turn on : 3.3 ~ 5.6V ; PSU turn off : 0 ~ 1V DC OK SIGNAL FUNCTION FAN CONTROL (Typ.) Load 20±10% or RTH2≧℃ 50 Fan on -40 ~ +70℃ (Refer to "Derating Curve") WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH TEMP. COEFFICIENT ±℃ 0.03%/ (0 ~ 50℃) VIBRATION 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS UL60950-1, TUV EN60950-1 approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH EMC (Note 4) EMC EMISSION Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2, heavy industry level, criteria A 139.9K hrs min. MIL-HDBK-217F (25℃) MTBF OTHERS DIMENSION 218*105*41mm (L*W*H) 1.19Kg; 12pcs/15.3Kg/0.82CUFT PACKING ‰„…ƒŠ„„‹ ­‹  „Œ ℃ „ NOTE ‹Ž‘„‹’
“ ŒˆŒ‰‹” ˆˆ„ˆ ‰ ‘•–   Š€ •Šˆ „ˆˆŒ —„˜’Œ™Œ„  œ„„š œ„„„ˆ‰„„ ›Š —„„Œ „„˜’ ˆ  „˜’ ž˜’Ÿ „ˆ¡¢Œ€ˆˆˆ„ˆ„£ †„Œˆ › „ œ¤ „„ Šƒ…ƒˆ„  „ File Name:HRP-450-SPEC 2015-07-14 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-HRP-450-power-supply.html h t t p: / / pow e r. sa ge r. c om MEAN WELL HRP-450 SERIES 450 Watt Enclosed with Fan Power Supply 450W Single Output with PFC Function HRP-450 series Measures: 8.56 x 4.13 x 1.61” Mechanical Mechanical Specification Specification Case No. 995A Unit:mm 152.4 32.8 O/P 1 2 Air flow 3 direction FAN 4 I/P 5 1 6 2 1 3 4-M4 L=5 3 2 4 218 152.4 32.8 18max. 12max. 8-M4 L=4 (Both Sides) Connector Pin No. Assignment(CN100) : HRS DF11-4DP-2DS or equivalent AC Input Terminal Pin No. DC Output Terminal Pin No. Assignment Assignment Pin No. Assignment Mating Housing Terminal DC-OK Pin No. Assignment Pin No. Assignment 1 2 GND 1 AC/L 1~3 -V HRS DF11-4DS HRS DF11-**SC or equivalent or equivalent +S 2 AC/N 4~6 +V 3 3 FG 4 -S Block Diagram PMW fosc : 70KHz +S ACTIVE RECTIFIERS RECTIFIERS EMI +V INRUSH POWER & I/P & FILTER CURRENT SWITCHING -V PFC FILTER LIMITING -S DETECTION O.L.P. O.T.P. CIRCUIT DC OK FG O.T.P. PWM PFC CONTROL CONTROL O.V.P. Derating Curve Output Derating VS Input Voltage 100 125 90 100 80 80 70 60 50 50 20 40 -40 0 10 20 30 40 50 60 70 (HORIZONTAL) 85 100 125 135 155 264 AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (V) 60Hz File Name:HRP-450-SPEC 2015-07-14 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-HRP-450-power-supply.html h t t p: / / pow e r. sa ge r. c om LOAD (%) 41 10 8.2 12.5 18 63.5 20.75 LOAD(%) 9.2 11 CN100 LED (Vo ADJ.)SVR1 105 MEAN WELL HRP-450 SERIES 450 Watt Enclosed with Fan Power Supply 450W Single Output with PFC Function HRP-450 series Measures: 8.56 x 4.13 x 1.61” Function Description of CN100 Pin No. Function Description DC-OK Signal is a TTL level signal, referenced to pin2(DC-OK GND). High when PSU turns on. 1 DC-OK This pin connects to the negative terminal(-V). Return for DC-OK signal output. 2 GND Positive sensing. The +S signal should be connected to the positive terminal of the load. The +S and -S leads should be twisted in pair to 3 +S minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and +S leads should be twisted in pair to 4 -S minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Function Manual CN100 1.Remote Sense The remote sensing compensates voltage drop on CN100 the load wiring up to 0.5V. 2 1 4 3 2 GND DC-OK 1 3 4 -S +S + - +S -S (Pin3) (Pin4) LOAD Sense lines should Fig 1.1 be twisted in pairs CN100 2.DC-OK Signal DC-OK signal is a TTL level signal. High when PSU turns on. CN100 Between DC-OK(pin5) and GND(pin6) Output Status 2 1 1 4 3 2 GND DC-OK 3.3 ~ 5.6V ON 0 ~ 1V OFF 4 -S +S 3 Fig 2.1 File Name:HRP-450-SPEC 2015-07-14 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-HRP-450-power-supply.html h t t p: / / pow e r. sa ge r. c om