MEAN WELL HRPG-600-5

MEAN WELL HRPG-600 SERIES 600 Watt Enclosed with Fan Power Supply 600W Single Output with PFC Function HRPG-600Measures: 8.58 x 4.13 x 2.5” series ■‚ � �     �
  � ­ € � ‚ƒ„„„… �  „†„ � ‡„ˆ � …„†„ �ƒ‰€­Š  � …  �†‹…ŒŽ€‘†Ž’ �“‘ ”•’‘“­ –­­’ �€‹ SPECIFICATION MODEL HRPG-600-3.3 HRPG-600-5 HRPG-600-7.5 HRPG-600-12 HRPG-600-15 HRPG-600-24 HRPG-600-36 HRPG-600-48 DC VOLTAGE 3.3V 5V 7.5V 12V 15V 24V 36V 48V RATED CURRENT 120A 120A 80A 53A 43A 27A 17.5A 13A CURRENT RANGE 0 ~ 120A 0 ~ 120A 0 ~ 80A 0 ~ 53A 0 ~ 43A 0 ~ 27A 0 ~ 17.5A 0 ~ 13A RATED POWER 396W 600W 600W 636W 645W 648W 630W 624W RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p 100mVp-p 120mVp-p 150mVp-p 150mVp-p 200mVp-p 240mVp-p OUTPUT VOLTAGE ADJ. RANGE 2.8 ~ 3.8V 4.3 ~ 5.8V 6.8 ~ 9V 10.2 ~ 13.8V 13.5 ~ 18V 21.6 ~ 28.8V 28.8 ~ 39.6V 40.8 ~ 55.2V VOLTAGE TOLERANCE Note.3 ±2.0% ±2.0% ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.3% ±0.3% ±0.2% ±0.2% ±0.2% LOAD REGULATION ±1.0% ±1.0% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME 1000ms, 50ms/230VAC 2500ms, 50ms/115VAC at full load HOLD UP TIME (Typ.) 16ms/230VAC 16ms/115VAC at full load VOLTAGE RANGE Note.5 85 ~ 264VAC 120 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.94/230VAC PF>0.99/115VAC at full load INPUT EFFICIENCY (Typ.) 78.5% 82% 86% 88% 88% 88% 89% 89% AC CURRENT (Typ.) 7.6A/115VAC 3.6A/230VAC INRUSH CURRENT (Typ.) 35A/115VAC 70A/230VAC LEAKAGE CURRENT <1.2mA / 240VAC 105 ~ 135% rated output power OVERLOAD Protection type : Constant current limiting, recovers automatically after fault condition is removed 6 ~ 7V 9.4 ~ 10.9V 14.4 ~ 16.8V 18.8 ~ 21.8V 30 ~ 34.8V 41.4 ~ 48.6V 57.6 ~ 67.2V PROTECTION 3.96 ~ 4.62V OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down OVER TEMPERATURE 5VSB : 5V@0.3A ; tolerance±5%, ripple : 50mVp-p(max.) 5V STANDBY DC OK SIGNAL PSU turn on : 3.3 ~ 5.6V ; PSU turn off : 0 ~ 1V FUNCTION REMOTE CONTROL RC+ / RC-: 4 ~ 10V or open = power on ; 0 ~ 0.8V or short = power off Load 35±15% or RTH2≧℃ 50 Fan on FAN CONTROL (Typ.) -40 ~ +70℃ (Refer to "Derating Curve") WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT -40 ~ +85℃, 10 ~ 95% RH STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT ±℃ 0.03%/ (0 ~ 50℃) VIBRATION 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS UL60950-1, TUV EN60950-1 approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH EMC (Note 4) EMC EMISSION Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2, heavy industry level, criteria A 147.7K hrs min. MIL-HDBK-217F (25℃) MTBF OTHERS DIMENSION 218*105*63.5mm (L*W*H) PACKING 1.58Kg;8pcs/13.6Kg/1.34CUFT •…†„—……“ ­“€  …‰ ℃ … NOTE “˜™…“š
› ‰‹‰•“œ ‹‹…‹ • ™Ž   —‚ —‹ …‹‹‰ ž…Ÿš‰¡‰…  –……¢ –………‹•…… £— ž……‰ ……Ÿš ‹  …Ÿš ¤Ÿš¥ …‹¦‘‰‚‹‹‹…‹…’ €‡…‰‹ £ … –§ …… —„†„‹…  … Ž†‹…ŒŽ€‹˜”™˜‘ †• ’¨­  File Name:HRPG-600-SPEC 2015-06-22 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-HRPG-600-power-supply.html h t t p: / / pow e r. sa ge r. c om MEAN WELL HRPG-600 SERIES 600 Watt Enclosed with Fan Power Supply 600W Single Output with PFC Function HRPG-600 series Measures: 8.58 x 4.13 x 2.5” Mechanical Mechanical Specification Specification Case No. 977A Unit:mm 152.4 32.8 O/P 1 4-M4 L=6 2 Air flow 3 direction 4 I/P 5 1 6 2 1 9 3 2 10 218 152.4 32.8 8-M4 L=4 (Both Sides) 18max. 12max. AC Input Terminal Pin No. DC Output Terminal Pin No. Connector Pin No. Assignment(CN100) : HRS DF11-10DP-2DS or equivalent Assignment Assignment Pin No. Assignment Pin No. Assignment Mating Housing Terminal 1 AUXG 6,8 GND Pin No. Assignment Pin No. Assignment 1 AC/L 1~3 -V 2 AUX 7 DC-OK HRS DF11-10DS HRS DF11-**SC 3 RC+ 9 +S 2 AC/N 4~6 +V or equivalent or equivalent 4 RC- -S 3 FG 10 5 CS Block Diagram PWM fosc : 70KHz RECTIFIERS AUX AUX & POWER AUXG FILTER +S ACTIVE RECTIFIERS RECTIFIERS EMI +V INRUSH POWER & I/P & FILTER CURRENT SWITCHING -V PFC FILTER LIMITING -S DETECTION O.T.P. O.L.P. CIRCUIT DC OK FG O.T.P. CURRENT PWM PFC O.V.P. CS SHARING CONTROL CONTROL RC+ REMOTE CONTROL RC- Derating Curve Output Derating VS Input Voltage 100 125 90 100 80 80 70 60 50 The 5V standby must be connected 50 with a minimum load of 0.03A. 20 40 -40 -20 10 20 30 40 50 60 70 (HORIZONTAL) 85 100 125 135 155 264 AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (V) 60Hz File Name:HRPG-600-SPEC 2015-06-22 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-HRPG-600-power-supply.html h t t p: / / pow e r. sa ge r. c om LOAD (%) 10 8.2 63.5 20.75 LOAD(%) 9.2 11 12.5 38.3 63.5 CN100 LED (Vo ADJ.)SVR1 105 MEAN WELL HRPG-600 SERIES 600 Watt Enclosed with Fan Power Supply 600W Single Output with PFC Function HRPG-600 series Measures: 8.58 x 4.13 x 2.5” Function Description of CN100 Pin No. Function Description Auxiliary voltage output ground. The signal return is isolated from the output terminals (+V & -V). 1 AUXG Auxiliary voltage output, 4.75~5.25V, referenced to pin 1(AUXG). The maximum load current is 0.3A. This output is not controlled by the 2 AUX "remote ON/OFF control". 3 RC+ Turns the output on and off by electrical or dry contact between pin 4 (RC-), Short: Power OFF, Open: Power ON. 4 RC- Remote control ground. Current sharing signal. When units are connected in parallel, the CS pins of the units should be connected to allow current balance 5 CS between units. This pin connects to the negative terminal(-V). Return for DC-OK signal output. 6,8 GND 7 DC-OK DC-OK signal is a TTL level signal, referenced to pin8(DC-OK GND). High when PSU turns on. Positive sensing. The +S signal should be connected to the positive terminal of the load. The +S and -S leads should be twisted in pair to 9 +S minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and +S leads should be twisted in pair to 10 -S minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Function Manual 1.Remote Sense The remote sensing compensates voltage drop on CN100 the load wiring up to 0.5V. CN100 1 2 AUX AUXG 1 2 RC- RC+ 9 10 GND CS GND DC-OK 10 9 -S +S + - +S -S (Pin9) (Pin10) LOAD Sense lines should be twisted in pairs Fig 1.1 2.DC-OK Signal DC-OK signal is a TTL level signal. High when PSU turns on. CN100 Between DC-OK(pin7) and GND(pin6,8) Output Status CN100 AUX AUXG 2 1 3.3 ~ 5.6V ON 1 2 RC- RC+ 9 0 ~ 1V OFF 10 GND CS GND DC-OK 10 -S +S 9 Fig 2.1 File Name:HRPG-600-SPEC 2015-06-22 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-HRPG-600-power-supply.html h t t p: / / pow e r. sa ge r. c om MEAN WELL HRPG-600 SERIES 600 Watt Enclosed with Fan Power Supply 600W Single Output with PFC Function HRPG-600 series Measures: 8.58 x 4.13 x 2.5” 3.Remote Control The PSU can be turned ON/OFF by using the CN100 "Remote Control" function. CN100 AUX AUXG 1 2 Between RC+(pin3) and RC-(pin4) Output Status 2 1 RC- RC+ SW ON (Short) OFF 9 10 GND CS SW OFF (Open) ON GND DC-OK 10 -S +S 9 SW Fig 3.1 4.Current Sharing with Remote Sensing (Only for 24V, 36V and 48V) HRPG-600 has the built-in active current sharing function and can be connected in parallel to provide higher output power : (1)Parallel operation is available by connecting the units shown as below. (+S,-S,CS and GND are connected mutually in parallel). (2)Difference of output voltages among parallel units should be less than 2%. (3)The total output current must not exceed the value determined by the following equation. (output current at parallel operation)=(Rated current per unit)×× (Number of unit) 0.9 (4)In parallel operation 4 units is the maximum, please consult the manufacturer for applications of more connecting in parallel. (5)The power supplies should be paralleled using short and large diameter wiring and then connected to the load. PSU1 PSU2 PSU3 PSU4 -V -V -V -V +V +V +V +V CN100 CN100 CN100 CN100 PSU1 PSU2 PSU3 PSU4 CN100 CN100 CN100 CN100 1 AUXG RC+ CS DC-OK +S 9 1 AUXG RC+ CS DC-OK +S 9 1 AUXG RC+ CS DC-OK +S 9 1 AUXG RC+ CS DC-OK +S 9 2 AUX RC- GND GND -S 10 2 AUX RC- GND GND -S 10 2 AUX RC- GND GND -S 10 2 AUX RC- GND GND -S 10 Sense lines should be twisted in pairs +V -V LOAD Fig 4.1 Note : 1.In parallel connection, maybe only one unit (master) operate if the total output load is less than 2% of rated load condition. The other PSU (slave) may go into standby mode and its output LED and relay will not turn on. 2.2% min. of dummy load is required. File Name:HRPG-600-SPEC 2015-06-22 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-HRPG-600-power-supply.html h t t p: / / pow e r. sa ge r. c om