MEAN WELL HSP-200-5

200W Single Output with PFC Function HSP-200 series ■��������! ‧�������������������������� ‧������������������������� ‧��������������������� � ‧�����������!"#�����������$������%�$�����������$����� �������� ‧����������!&� ‧������ �������% ‧�’(��%���������������� ‧&)�����������) Bauart gepruft Sicherheit egelma ge od os S&E be wac g www.tuv.com ID 2000000000 SPECIFICATION MODEL HSP-200-4.2 HSP-200-5 5V DC VOLTAGE 4.2V RATED CURRENT 40A 40A CURRENT RANGE 0 ~ 40A 0 ~ 40A RATED POWER(convection) 168W 200W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p OUTPUT VOLTAGE ADJ. RANGE 3.6~4.4V 4.5~5.5V VOLTAGE TOLERANCE Note.3 ±2.0% ±2.0% LINE REGULATION ±0.5% ±0.5% LOAD REGULATION ±1.0% ±1.0% SETUP, RISE TIME 2000ms, 200ms/230VAC 3000ms, 200ms/115VAC at full load HOLD UP TIME (Typ.) 16ms/230VAC 16ms/115VAC at full load VOLTAGE RANGE Note.4 90 ~ 264VAC 127 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz PF≥≥ 0.95/230VAC PF 0.98/115VAC at full load POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) 88% 88.5% 3.0A/115VAC 2.0A/230VAC AC CURRENT (Typ.) 2.5A/115VAC 1.5A/230VAC INRUSH CURRENT (Typ.) Cold start 70A/230VAC LEAKAGE CURRENT <1.0mA / 240VAC 110~140% rated output power OVERLOAD Protection type : Hiccup mode, recovers automatically after fault condition is removed SHORT CIRCUIT Protection type : Hiccup mode, recovers automatically after fault condition is removed PROTECTION 4.6 ~ 5.4V 5.6 ~ 7.0V OVER VOLTAGE Protection type : Hiccup mode, recovers automatically after fault condition is removed OVER TEMPERATURE Shut down O/P voltage, recovers automatically after fault condition is removed -30 ~ +70℃(Refer to "Derating Curve") WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT -40 ~ +85℃, 10 ~ 95% RH STORAGE TEMP., HUMIDITY ±℃ 0.03%/ (0 ~ 60℃) TEMP. COEFFICIENT 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes VIBRATION SAFETY STANDARDS UL60950-1,TUV EN60950-1,CCC GB4943,EAC TP TC 004 approved WITHSTAND VOLTAGE I/P-O/P:3.0KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC/25℃/ 70%RH EMC EMC EMISSION Compliance to EN55032 (CISPR32),GB9254,Class B, EN61000-3-2,-3,GB17625.1, EAC TP TC 020 (Note 5) Compliance to EN61000-4-2,3,4,5,6,8,11;EN55024, light industry level (surge 4KV), criteria A, EAC TP TC 020 EMC IMMUNITY MTBF 204K hrs min. MIL-HDBK-217F (25℃) OTHERS 210*62*31mm (L*W*H) DIMENSION PACKING 0.52kg; 20pcs/ 11.4kg/0.76CUFT ��������� �����*$+��������) �������%��� ������%��,&�-�������.����%���%��%,/℃��� 0������ ��������� ,�1�����2�������� ������%��,�345��0��%��%�#0)�������,6������%������������ �����%���#������278�������������������� NOTE &�+��������!����������������%���%����������� 7�(������� �)0����%�%��%��������������������������#����#��������#���������������� ���%������� /������#��������� ��� ������%�����%�����������+������$*�$���#�����������) �)���%�������������#�������� �� 9�+#�����������)�������%���%��� �������#��#����0���������%�����������:��� ��������#�’3���������0����;�����%0) ��������#�����<�� �7/� =7/� ������������#� ���#��������+#�������:��� ��� ���0���������� �%�#��������� ����’3�%����������������%������#���� ������ �#���’3������.�������������>’3?����������� ��������������������@A��������0����#���!������ ���������� B File Name:HSP-200-SPEC 2018-01-09 200W Single Output with PFC Function HSP-200 series Mechanical Specification CASE NO.: 232B Unit:mm 210 2 206 13 SVR1 TB1 1 3 2 2 3 1 4 4-ψ3.3 AC Input Terminal(TB1) pin NO. Assignment DC Output Terminal pin NO. Assignment Pin No. Assignment Terminal Pin No. Assignment Terminal 1 AC/L 1,2 -V K14-20A(H) 2 DG28C-B-03P AC/N 3,4 +V 3 Block Diagram POWER SYNCHRONOUS +V EMI BRIDGE APFC I/P SWITCH- RECTIFIERS RECTIFIERS CONTROLLER FILTER -V ING & FILTER O.T.P. FG DETECTION PWM O.L.P. CIRCUIT CONVERTER O.V.P. Derating Curve Static Characteristics fosc=90Khz 4.2V 100 100 80 80 5V 70 60 60 40 40 20 20 14 -30 -25 -10 0 15 30 50 60 70 (HORIZONTAL) 90 100 110 135 155 230 264 INPUT VOLTAGE (V) 60Hz AMBIENT TEMPERATURE (℃) File Name:HSP-200-SPEC 2018-01-09 load(%) 62 46.4 7.8 load(%) 31 450 200W Single Output with PFC Function HSP-200 series Installation 1.Operate with additional aluminum plate In order to meet the“Derating Curve”and the “Static Characteristics” ,HSP-200 series must be installed onto an aluminum plate(or the cabinet of the same size) on the bottom.The size of the suggested aluminum plate is shown as below. And for optimizing thermal performance, the aluminum plate must have an even and smooth surface (or coated with thermal grease), and HSP-200 series must be firmly mounted at the center of the aluminum plate. M3*4 2.For heat dissipation, at least 5cm installation distance around the PSU should be kept, shown as below: 13 SVR1 5cm 5cm File Name:HSP-200-SPEC 2018-01-09 450 /� /� 3 /�