MEAN WELL SDR-960-48

Mean Well SDR-960 SERIES 960 Watt DIN Rail Mount Power Supply 960W Single Output Industrial DIN RAIL with PFC Function SDR-960 series Measures: 5.91 x 4.93 x 4.33” ■ � ”˜Œ…  �™Ž   �‚ �—„  ‰“     ˆŒ„„ �‚€  š…™  ­ ­ �“   ›€   œ‰ œ‰‰ ‚œ‰ �  ‚ ‰  �—„      ‚   �   ’Š›„
Ϡ
 
�ž–
”Ÿ   ‡ ¡ ‰ �ˆŒ„Œ„Ÿˆ
”„¡  ‰ � € ‚ ”…•Ÿ¢¡ �—„ ’£   �™  „  �­  SPECIFICATION MODEL SDR-960-24 SDR-960-48 DC VOLTAGE 24V 48V RATED CURRENT 40A 20A CURRENT RANGE 0 ~ 40A 0 ~ 20A RATED POWER 960W 960W PEAK CURRENT 52A 26A PEAK POWER Note.6 1248W (3sec.) OUTPUT RIPPLE & NOISE (max.) Note.2 180mVp-p 250mVp-p VOLTAGE ADJ. RANGE 24 ~ 28V 48 ~ 55V VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.5% LOAD REGULATION ±1.0% ±1.0% SETUP, RISE TIME 1000ms, 100ms/230VAC at full load HOLD UP TIME (Typ.) 14ms / 230VAC at full load VOLTAGE RANGE Note.7 180 ~ 264VAC 254 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF≧0.95/230VAC at full load EFFICIENCY (Typ.) 94% 94% INPUT AC CURRENT (Typ.) 6A/230VAC INRUSH CURRENT (Typ.) COLD START 50A / 230VAC LEAKAGE CURRENT <3.5mA / 240VAC Normally works within 105 ~ 130% rated output power for more than 3 seconds and then shut down o/p voltage with auto-recovery after 30 seconds if the peak load condition is removed OVERLOAD Constant current limiting within 130 ~ 150% rated output power for more than 3 seconds and then shut down o/p voltage, re-power on to recover PROTECTION 29 ~ 33V 56 ~ 65V OVER VOLTAGE Protection type : Shut down o/p voltage, with auto-recovery or re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down OVER TEMPERATURE 60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load DC OK REALY CONTACT RATINGS (max.) FUNCTION Please refer to function manual CURRENT SHARING WORKING TEMP. Note.5 -30 ~ +70℃ (Refer to "Derating Curve") WORKING HUMIDITY 20 ~ 95% RH non-condensing STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH ENVIRONMENT TEMP. COEFFICIENT ±℃ 0.03%/ (0 ~ 50℃) VIBRATION Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6 SAFETY STANDARDS UL508, TUV EN60950-1 approved ; (meet EN60204-1) WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25℃/ 70% RH EMC (Note 4) EMC EMISSION Note.8 Compliance to EN55022 (CISPR22), EN61204-3 Conduction class B, Radiation class A, EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level, criteria A MTBF 69.8K hrs min. MIL-HDBK-217F (25℃) OTHERS DIMENSION 110*125.2*150mm (W*H*D) 2.47Kg ; 6pcs/15.8Kg/1.55CUFT PACKING       
℃   NOTE     ­€ ‚ƒ ­„­ ­€…†          ‚   ‚  …€ ­    ­€ €­     ‡ € ‡ „ € ˆ ‰
Š    …   €  
 € ‚€  ­€    ­€ ­ Š  €‹  ‰ €  
     Œ Ž ­‘ €‰‚  ­€  ‘ € ­ †’ ‚   ­ ‰ ‚“ € Ž€ ‚ ‰   ” ˆ•ˆ––      — File Name:SDR-960-SPEC 2015-10-20 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-SDR-960-power-supply.html h t t p: / / pow e r. sa ge r. c om +V ADJ + DC OK 35 Mean Well SDR-960 SERIES 960 Watt DIN Rail Mount Power Supply 960W Single Output Industrial DIN RAIL with PFC Function SDR-960 Measures: 5.91 x 4.93 x 4.33” series Mechanical Specification Case No.214A Unit:mm 12 3 4 125.2 CN205 1234 1 2 3 TB1 4 5 1 6 2 TB2 3 ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15 Terminal Pin No. Assignment (TB1) Terminal Pin No. Assignment (TB2) Control Pin (CN205) : DINKLE ECH250R-04P or equivalent Pin No. Assignment Pin No. Assignment Pin No. Assignment Mating Housing Wire Diameter DINKLE ESC250V-04P 1 FG 1,2,3 DC OUTPUT +V 1 P-(Current Share) 2 0.081~0.517mm or equivalent 2 AC/N 4,5,6 DC OUTPUT -V 2 P+(Current Share) (Including in the (28~20AWG) 3 AC/L 3,4 DC OK Relay Contact single package) Block Diagram PFC fosc : 65KHz PWM fosc : 60KHz DC OK RECTIFIERS EMI FILTER POWER PFC +V I/P & & SWITCHING CIRCUIT -V RECTIFIERS FILTER O.C.P. U.V.P. O.L.P. DETECTION FG PWM & PFC CIRCUIT PFC CONTROL CURRENT CONTROL CURRENT SHARE SHARE O.T.P. O.V.P. DC OK Relay Contact Contact Close PSU turns on / DC OK. Contact Open PSU turns off / DC Fail. Contact Ratings (max.) 30V/1A resistive load. File Name:SDR-960-SPEC 2015-10-20 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-SDR-960-power-supply.html h t t p: / / pow e r. sa ge r. c om 110 150 Mean Well SDR-960 SERIES 960 Watt DIN Rail Mount Power Supply Measures: 5.91 x 4.93 x 4.33” 960W Single Output Industrial DIN RAIL with PFC Function SDR-960 series Peak Loading ( 1 ) ( 2 ) 1248W 1248W 960W 480W 50 sec. 3 sec. 15 sec. 3 sec. Derating Curve Output derating VS input voltage 100 130 90 100 80 80 For 3 sec. (typ.) Continuous 70 60 60 40 50 20 40 -30 0 10 20 30 40 50 60 70 (VERTICAL) 180 190 200 210 220 230 240 250 264 AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (V) 60Hz Function Manual 1. Current sharing (1) Parallel operation is available by connecting the units shown as below (P+,P- are connected mutually in parallel). (2) Difference of output voltages among parallel units should be less than 0.2V. (3) The total output current must not exceed the value determined by the following equation (Output current at parallel operation)=(The rated current per unit) x (Number of unit) x 0.9. (4) In parallel operation 4 units is the maximum, please consult the manufacture for other applications. (5) The power supplies should be paralleled using short and large diameter wiring and then connected to the load. (6) When in parallel operation, the minimum output load should be greater than 5% of total output load. (Min. load >5% rated current per unit x number of unit) (7) In parallel connection, maybe only one unit (master) operate if the total output load is less than 5% of rated load condition. The other PSUs (slaves) may go into standby mode and their output LEDs & relays will not turn on. (8) Some minor noise may be heard at light load condition under parallel operation. This is a normal phenomenon and the performance of the PSU will not be influenced. PSU PSU PSU PSU TB2 TB2 TB2 TB2 -V +V -V +V -V +V -V +V CN205 CN205 CN205 CN205 1111 P- P- P- P- 2222 P+ P+ P+ P+ 3333 DC OK DC OK DC OK DC OK 4444 DC OK DC OK DC OK DC OK P-(pin1) P+(pin2) P+ and P- lines should be twisted in pairs -V +V LOAD File Name:SDR-960-SPEC 2015-10-20 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-SDR-960-power-supply.html h t t p: / / pow e r. sa ge r. c om LOAD (%) LOAD (%)