MEAN WELL SP-750-12

MEAN WELL SP-750 SERIES 750 Watt Enclosed with Fan Power Supply 750W Single Output Power Supply SP -750 s eri es Measures: 10.95 x 5.00 x 2.50” ■ Features : ‧Universal AC input / Full range ‧AC input active surge current limiting ‧Built-in active PFC function,PF>0.96 ‧Protections: Short circuit / Overload / Over voltage / Over temperature ‧Forced air cooling by built-in DC ball bearing fan 3 ‧High power density 5.48/inch ‧Built-in constant current limiting circuit ‧With power good and fail signal output ‧Built-in remote ON-OFF control ‧Built-in remote sense function ‧3 years warranty SPECIFICATION MODEL SP-750-5 SP-750-12 SP-750-15 SP-750-24 SP-750-27 SP-750-48 DC VOLTAGE 5V 12V 15V 24V 27V 48V RATED CURRENT 120A 62.5A 50A 31.3A 27.8A 15.7A CURRENT RANGE 0 ~ 120A 0 ~ 62.5A 0 ~ 50A 0 ~ 31.3A 0 ~ 27.8A 0 ~ 15.7A RATED POWER 600W 750W 750W 751.2W 750.6W 753.6W RIPPLE & NOISE (max.) Note.2 120mVp-p 120mVp-p 120mVp-p 120mVp-p 120mVp-p 120mVp-p OUTPUT VOLTAGE ADJ. RANGE 4.75 ~ 5.5V 10 ~ 13.5V 13.5 ~ 16.5V 22 ~ 26.4V 24 ~ 30V 43 ~ 56V VOLTAGE TOLERANCE Note.3 ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.3% ±0.3% ±0.2% ±0.2% ±0.2% LOAD REGULATION ±2.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME 1500ms, 50ms/230VAC 1500ms, 50ms/115VAC at full load HOLD UP TIME (Typ.) 16ms/230VAC 16ms/115VAC at full load VOLTAGE RANGE 90 ~ 264VAC 127 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.96/230VAC PF>0.99/115VAC at full load INPUT EFFICIENCY (Typ.) 80% 85% 87% 89% 89% 90% AC CURRENT (Typ.) 8.8A/115VAC 4.2A/230VAC INRUSH CURRENT (Typ.) 27A/115VAC 45A/230VAC LEAKAGE CURRENT <2.0mA / 240VAC 105 ~ 125% rated output power OVERLOAD Protection type : Constant current limiting, unit will Hiccup after 3 sec. 5.75 ~ 6.75V PROTECTION 13.8 ~ 16.2V 18 ~ 21V 27.6 ~ 32.4V 31 ~ 36.5V 57.6 ~ 67.2V OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down OVER TEMPERATURE POWER GOOD/FAIL 50ms/1ms FUNCTION REMOTE CONTROL Note.5 RC+/RC- short power on, open power off -20 ~ +60℃ (Refer to "Derating Curve") WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH ±℃ 0.05%/ (0 ~ 50℃) TEMP. COEFFICIENT VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 approved SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH (Note 4) EMC EMISSION Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A MTBF 105.4K hrs min. MIL-HDBK-217F (25℃) OTHERS DIMENSION 278*127*63.5mm (L*W*H) 2.9Kg; 6pcs / 18.4Kg / 0.98CUFT PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) 5. The power supply unit will have no output if the shorting connector is not assembled between RC+ & RC-. File Name:SP-750-SPEC 2013-11-07 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-SP-750-power-supply.html h t t p: / / pow e r. sa ge r. c om MEAN WELL SP-750 SERIES 750 Watt Enclosed with Fan Power Supply 750W Single Output Power Supply SP -750 s eri es Measures: 10.95 x 5.00 x 2.50” Mechanical Specification Case No.919A Unit:mm 113 7 220 16 4-M3 6-M3 L=6 4-M3 Air flow O/P direction 1 I/P 1 33 72 2 2 5 1 3 6 2 7 3 8 4 240 5 CONTROL 24.5 251 278 19 max. 20 max. 4-M3 2-M6 28 max. 220 15 BOTTOM VIEW TOP VIEW AC Input Terminal DC Output Terminal Control Pin No. Assignment : MOLEX 5559-NP uses 5558male crimp terminal Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment Mating connector Terminal Pin No. Assignment 1 AC/L 1 DC OUTPUT +V 1 NC 5 NC MOLEX 5556 2 AC/N 2 -S 6 PF(Power fail signal) 2 DC OUTPUT -V Female crimp MOLEX 5557-NR Terminal 3 FG 3 G 7 +S receptacle RC- RC+ 4 8 Block Diagram PFC fosc : 100KHz PWM fosc : 140KHz +S ACTIVE PFC PWM RECTIFIERS EMI +V INRUSH RECTIFIERS I/P POWER POWER & CURRENT FILTER -V SWITCHING SWITCHING FILTER LIMITING -S CURRENT O.T.P. DETECTION LIMIT FG CIRCUIT O.L.P. DETECTION PF PFC PWM CIRCUIT CONTROL CONTROL O.V.P. O.T.P. REMOTE RC CONTROL AUX FAN FAN LOCK POWER PROTECTION File Name:SP-750-SPEC 2013-11-07 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-SP-750-power-supply.html h t t p: / / pow e r. sa ge r. c om MEAN WELL SP-750 SERIES 750 Watt Enclosed with Fan Power Supply 750W Single Output Power Supply SP -750 s eri es Measures: 10.95 x 5.00 x 2.50” Derating Curve Static Characteristics 100 100 90 80 85 70 60 60 40 50 20 40 -20 0 10 20 30 40 50 60 70 (HORIZONTAL) 90 95 100 115 264 AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (VAC) 60Hz Control Terminal Instruction Manual Remote Sensing Power Fail Signal (1)PF Signal is the voltage difference between "G" and "PF" pin output. (2)When in power fail signal operation, the minimum output load should be greater than 3% of total output load. G PF RC+ +S PF NC RC+ +S PF NC RC- G -S NC RC- G -S NC -V +V -V +V LOAD LOAD - -S - + + +S Remote Control Power ON: RC+/RC- Short Power OFF: RC+/RC- open RC- RC+ RC+ +S PF NC RC- G -S NC -V +V LOAD - + File Name:SP-750-SPEC 2013-11-07 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/mean-well-SP-750-power-supply.html h t t p: / / pow e r. sa ge r. c om