MOLEX 0878321040

9 8 7 6 5 4 3 2 1 FEATURES CIRCUIT DUAL CENTER FRICTION LOCKS SHEET SIZE SIDE SLOTS POLARIZATION PEGS FEATURES SELECTION GUIDE NO DUAL CENTER 1 2 5 3 4 N.A N.A N.A N.A YES 4 2 - 3 E E N.A YES YES N.A N.A N.A N.A YES N.A N.A N.A N.A YES N.A YES 6 N.A N.A YES YES N.A 4 - 5 N.A YES YES N.A N.A N.A YES YES N.A YES N.A N.A YES YES YES N.A N.A YES YES N.A 2 CENTER LOCK 8 TO 12 6 - 7 N.A YES YES N.A N.A D D N.A YES YES N.A YES YES N.A YES YES N.A 14 TO 50 8 - 11 YES N.A YES YES YES 3 DUAL SIDE SLOTS 4 CENTER POLARIZATION C C 1 DUAL LOCKS 5 PEGS B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES (UNLESS SPECIFIED) MM NTS DRWN BY DATE MM INCH 4 PLACES ± ± GMENARLY 2015/05/22 MILLIGRID 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A 1 PLACES ± ± APPR BY DATE PRODUCT CUSTOMER DRAWING 0 PLACES ± ± KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION GENERAL MARKET 87832 SEE TABLE DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 1 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 Y A 4 CIRCUITS B RIBS LOCATION VARY DEPENDING ON CKT SIZES C DETAIL1 CKT #2 ⌀0.71±0.05 TYP E E ℄ OF C 2.00 4.50 5.00 6.30 CKT #1 DETAIL1 C/2 2.00 TYP Z ISO VIEW OF HEADER WITH ONLY DUAL SLOTS D D �3.90� H 4.70 6.40 7.60 6 G (COPLANARITY) 1.20 TYP Z SECTION Z-Z 2.00 F (TYP) 1.00 2.00 C C (TYP) 0.50±0.05 ℄ OF C 4.60 SQ. TYP ⌖0.50 Y 6.35 RIBS LOCATION VARY DEPENDING ON CKT SIZES ℄ OF C �5.30� & FEATURES TYP �0.65� TYP 1.50 2.75 �9.05� (TYP) C/2 C B B NOTES: C/2 1. MATERIALS: C HOUSING & CAP: 30% GF, NYLON, UL94V-0, COLOR: BLACK PIN: 0.50mm SQ. PHOSPHOR BRONZE RECOMMENDED PCB LAYOUT VIEW FOR HEADER WITH CAP 2. FINISHES: REFER TO PLATING OPTIONS 3. PRODUCT SPECIFICATION: PS-87831-027 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE 4. PACKAGING SPECIFICATION: SEE PACKAGING SPECS TABLE ON SHEET 12 GENERAL TOLERANCES 5. MATES WITH: A. MOLEX CRIMP RECEPTACLE HOUSING: 51110 SERIES (UNLESS SPECIFIED) MM NTS AND CRIMP TERMINAL: 50394 SERIES DRWN BY DATE MM INCH B. MOLEX 2mm MILLIGRID DUAL ROW IDT: 87568 SERIES 4 PLACES ± ± GMENARLY 2015/05/22 C. MOLEX 2mm MILLIGRID DUAL ROW RECEPTACLE: MILLIGRID 79107 (GOLD PLATED), 78787 (TIN PLATED) 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER COPLANARITY IS TO BE MEASURED BY RESTING THE SOLDERTAIL ON 6 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A A GAUGE SURFACE 1 PLACES ± ± APPR BY DATE 7. BEND DEPRESSION ON SMT TAIL IS ACCEPTABLE SO LONG AS IT PRODUCT CUSTOMER DRAWING 0 PLACES ± ± DOES NOT AFFECT THE OVERALL COPLANARITY KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER ANGULAR TOL ± 3.0 8. TOP SURFACE OF CAP TO BE FLAT FOR THE PURPOSE OF DRAWING SIZE THIRD ANGLE PROJECTION GENERAL MARKET 87832 SEE TABLE PICK & PLACE BY VACUUM SUCTION NOZZLE DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 2 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 4 CIRCUITS T&R FRICTION LOCKS DIMENSION ASSY P/N ASSY P/N ASSY P/N DUAL E E CKT OPTIONS PLATING CENTER SIDE WITHOUT CAP WITH CAP WITH CAP PEGS G SIZE (SEE OPTIONS POLARIZATION DUAL CENTER A B C D E F H IN TUBE IN TUBE IN T&R SLOTS (COPLAN) SHEET 12) 87832-0460 87832-0462 87832-5162 1 1 87832-0420 87832-0422 87832-5122 1 2 N.A N.A YES N.A N.A 0.10 87832-0421 87832-0423 87832-5123 1 3 87832-0470 87832-0472 87832-5172 1 4 4 6.65 4.85 2.00 N.A N.A 5.00 3.60±0.20 87832-0406 1 2 87832-0410 87832-0408 87832-5106 2 2 0.10 N.A N.A N.A YES YES 87832-0411 87832-0409 87832-0407 1 3 87832-0404 N.A N.A N.A 2 0.10 D D C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION PLATING OPTIONS: DIMENSION UNITS SCALE GENERAL TOLERANCES 1 - 0.05-0.13µm/2-5µin GOLD IN CONTACT AREA AND (UNLESS SPECIFIED) MM NTS 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER DRWN BY DATE MM INCH 1.27µm/50µin MIN. NICKEL OVERALL. 4 PLACES ± ± 2 - 0.38µm/15µin MIN. GOLD IN CONTACT AREA AND GMENARLY 2015/05/22 MILLIGRID 1.88um/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 1.27µm/50µin MIN. NICKEL OVERALL. 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A 3 - 0.76µm/30µin MIN. GOLD IN CONTACT AREA AND 1 PLACES ± ± APPR BY DATE 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER PRODUCT CUSTOMER DRAWING 0 PLACES ± ± 1.27µm/50µin MIN. NICKEL OVERALL. KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER ANGULAR TOL ± 3.0 4 - 2.50µm/100µin MIN. MATTE TIN OVER 1.25µm/50µin MIN. NICKEL OVERALL. DRAWING SIZE THIRD ANGLE PROJECTION GENERAL MARKET 87832 SEE TABLE DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 3 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 Y A B RIBS LOCATION VARY 6 CIRCUITS DEPENDING ON CKT SIZES C DETAIL 2 CKT #2 E E ⌀0.71±0.05 TYP 2.00 4.50 5.00 6.30 CKT #1 2.00 TYP DETAIL 2 C/2 ℄ OF C Y VIEW FOR HEADER WITH �3.90� D H ONLY DUAL SLOTS D 4.70 6.40 7.60 6 G (COPLANARITY) 1.20 TYP 2.00 Y (TYP) 2.20 (2X) SECTION Y-Y E F 1.00 0.50±0.05 SQ (TYP) C C 2.00 TYP TYP 4.60 ℄ OF C 6.35 ℄ OF C ⌖ 0.50 Y ⌀1.00±0.05 (2X) �5.30� ⌀0.65±0.08 (2X) TYP 1.50 2.13 2.75 �0.65� RIBS LOCATION VARY (TYP) E TYP DEPENDING ON CKT SIZES �9.05� C/2 & FEATURES B B C C/2 NOTES: 1.00 1. MATERIALS: HOUSING & CAP: 30% GF, NYLON, UL94V-0, COLOR: BLACK C PIN: 0.50mm SQ. PHOSPHOR BRONZE RECOMMENDED PCB LAYOUT VIEW FOR HEADER WITH CAP 2. FINISHES: REFER TO PLATING OPTIONS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 3. PRODUCT SPECIFICATION: PS-87831-027 DIMENSION UNITS SCALE 4. PACKAGING SPECIFICATION: SEE PACKAGING SPECS TABLE ON SHEET 12 GENERAL TOLERANCES (UNLESS SPECIFIED) MM NTS 5. MATES WITH: A. MOLEX CRIMP RECEPTACLE HOUSING: 51110 SERIES AND CRIMP TERMINAL: 50394 SERIES DRWN BY DATE MM INCH B. MOLEX 2mm MILLIGRID DUAL ROW IDT: 87568 SERIES 4 PLACES ± ± GMENARLY 2015/05/22 C. MOLEX 2mm MILLIGRID DUAL ROW RECEPTACLE: MILLIGRID 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 79107 (GOLD PLATED), 78787 (TIN PLATED) 2 PLACES ± 0.2 ± 6 A COPLANARITY IS TO BE MEASURED BY RESTING THE SOLDERTAIL ON CGOH 2015/09/21 A 1 PLACES ± ± A GAUGE SURFACE APPR BY DATE PRODUCT CUSTOMER DRAWING 7. BEND DEPRESSION ON SMT TAIL IS ACCEPTABLE SO LONG AS IT 0 PLACES ± ± KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER DOES NOT AFFECT THE OVERALL COPLANARITY ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION 8. TOP SURFACE OF CAP TO BE FLAT FOR THE PURPOSE OF GENERAL MARKET 87832 SEE TABLE PICK & PLACE BY VACUUM SUCTION NOZZLE DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 4 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 6 CIRCUITS T&R FRICTION LOCKS DIMENSION ASSY P/N ASSY P/N ASSY P/N DUAL E E CKT OPTIONS PLATING CENTER SIDE WITHOUT CAP WITH CAP WITH CAP PEGS G SIZE (SEE OPTIONS POLARIZATION DUAL CENTER A B C D E F H IN TUBE IN TUBE IN T&R SLOTS (COPLAN) SHEET 12) 87832-0660 87832-0662 87832-5262 1 1 87832-0620 87832-0622 87832-5222 1 2 N.A N.A YES N.A YES 0.10 3.60±0.20 87832-0621 87832-0623 87832-5223 1 3 87832-0670 87832-0672 87832-5272 1 4 87832-0612 87832-0616 87832-0614 1 2 N.A N.A YES N.A N.A 0.10 3.60±0.20 6 87832-0613 87832-0617 87832-0615 1 3 N.A N.A YES YES N.A 8.65 6.85 4.00 N.A 2.00 7.00 87832-0624 87832-0626 87832-0628 1 2 N.A N.A N.A 0.10 3.60±0.15 YES YES 87832-0625 87832-0627 87832-0629 1 3 D D 87832-0610 87832-0608 87832-0606 1 2 N.A N.A 0.10 3.60±0.20 YES YES YES 87832-0611 87832-0609 87832-0607 1 3 87832-0604 N.A N.A N.A 2 N.A YES YES N.A YES 0.10 3.60±0.20 C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES PLATING OPTIONS: (UNLESS SPECIFIED) MM NTS 1 - 0.05-0.13µm/2-5µin GOLD IN CONTACT AREA AND DRWN BY DATE 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER MM INCH 1.27µm/50µin MIN. NICKEL OVERALL. 4 PLACES ± ± GMENARLY 2015/05/22 MILLIGRID 2 - 0.38µm/15µin MIN. GOLD IN CONTACT AREA AND 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A 1.27µm/50µin MIN. NICKEL OVERALL. 1 PLACES ± ± APPR BY DATE 3 - 0.76µm/30µin MIN. GOLD IN CONTACT AREA AND PRODUCT CUSTOMER DRAWING 0 PLACES ± ± 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER 1.27µm/50µin MIN. NICKEL OVERALL. ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION 4 - 2.50µm/100µin MIN. MATTE TIN OVER 1.25µm/50µin MIN. NICKEL OVERALL. GENERAL MARKET 87832 SEE TABLE DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 5 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 Y A 8 TO 12 CIRCUITS B RIBS LOCATION VARY DEPENDING ON CKT SIZES C DETAIL 3 E E CKT #2 ⌀0.71±0.05 TYP 2.00 4.50 5.00 6.30 CKT #1 DETAIL 3 C/2 ℄ OF C TYP 2.00 X CIRCUIT IDENTIFICATION D D �3.90� ISO VIEW OF HEADER WITH CENTER H 4.70 POLARIZATION AND DUAL SIDE SLOTS 6.40 7.60 6 G (COPLANARITY) 1.20 TYP E X 2.20 (2X) 1.00 2.00 SECTION X-X 0.50±0.05 SQ (TYP) (TYP) C C E TYP TYP 2.00 4.60 ⌀0.85±0.05 (2X) ⌀1.00±0.05 (2X) 6.35 ⌖ 0.50 Y ℄ OF C 1.50 �5.30� TYP 2.13 2.75 RIBS LOCATION VARY (TYP) DEPENDING ON CKT SIZES �9.05� & FEATURES C/2 �0.65� B B C C/2 TYP ℄ OF C F 1.00 NOTES: 1. MATERIALS: C HOUSING & CAP: 30% GF, NYLON, UL94V-0, COLOR: BLACK PIN: 0.50mm SQ. PHOSPHOR BRONZE VIEW FOR HEADER WITH CAP RECOMMENDED PCB LAYOUT 2. FINISHES: REFER TO PLATING OPTIONS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 3. PRODUCT SPECIFICATION: PS-87831-027 DIMENSION UNITS SCALE GENERAL TOLERANCES 4. PACKAGING SPECIFICATION: SEE PACKAGING SPECS TABLE ON SHEET 12 (UNLESS SPECIFIED) MM NTS 5. MATES WITH: A. MOLEX CRIMP RECEPTACLE HOUSING: 51110 SERIES DRWN BY DATE MM INCH AND CRIMP TERMINAL: 50394 SERIES B. MOLEX 2mm MILLIGRID DUAL ROW IDT: 87568 SERIES 4 PLACES ± ± GMENARLY 2015/05/22 MILLIGRID C. MOLEX 2mm MILLIGRID DUAL ROW RECEPTACLE: 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 79107 (GOLD PLATED), 78787 (TIN PLATED) 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A 6 COPLANARITY IS TO BE MEASURED BY RESTING THE SOLDERTAIL ON 1 PLACES ± ± APPR BY DATE A GAUGE SURFACE PRODUCT CUSTOMER DRAWING 0 PLACES ± ± 7. BEND DEPRESSION ON SMT TAIL IS ACCEPTABLE SO LONG AS IT KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER DOES NOT AFFECT THE OVERALL COPLANARITY ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION GENERAL MARKET 87832 SEE TABLE 8. TOP SURFACE OF CAP TO BE FLAT FOR THE PURPOSE OF DRAFT WHERE APPLICABLE PICK & PLACE BY VACUUM SUCTION NOZZLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 6 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 8 TO 12 CIRCUITS T&R FRICTION LOCKS DIMENSION ASSY P/N ASSY P/N ASSY P/N DUAL CKT OPTIONS PLATING CENTER WITHOUT CAP WITH CAP WITH CAP SIDE PEGS G SIZE (SEE OPTIONS POLARIZATION DUAL CENTER A B C D E F H IN TUBE IN TUBE IN T&R SLOTS (COPLAN) SHEET 12) 87832-0860 87832-0862 87832-5362 1 1 E E 87832-0820 87832-0822 87832-5322 1 2 N.A N.A YES YES YES 0.10 3.60±0.20 87832-0821 87832-0823 87832-5323 1 3 87832-0870 87832-0872 87832-5372 1 4 87832-0812 87832-0816 87832-0814 1 2 N.A N.A YES YES N.A 0.10 3.60±0.20 8 10.65 8.85 6.00 N.A 4.00 9.00 87832-0824 87832-0826 87832-0828 1 2 N.A YES YES N.A N.A 0.10 3.60±0.15 87832-0825 87832-0827 87832-0829 1 3 87832-0810 87832-0808 87832-0806 1 2 N.A YES YES N.A YES 0.10 3.60±0.20 87832-0811 87832-0809 87832-0807 1 3 87832-0804 N.A N.A N.A 2 N.A YES YES N.A YES 0.10 3.60±0.20 87832-1060 87832-1062 87832-5462 1 1 D D 87832-1020 87832-1022 87832-5422 1 2 87832-5423 1 N.A N.A YES YES YES 0.10 3.60±0.20 87832-1021 87832-1023 3 87832-9423 2 87832-1070 87832-1072 87832-5472 1 4 10 87832-1012 87832-1016 87832-1014 1 2 N.A N.A YES YES N.A 12.65 10.85 8.00 N.A 6.00 11.00 0.10 3.60±0.20 87832-1024 87832-1026 87832-1028 1 2 N.A YES YES N.A N.A 0.10 3.60±0.15 87832-1025 87832-1027 87832-1029 1 3 87832-1010 87832-1008 87832-1006 1 2 N.A YES YES N.A YES 0.10 3.60±0.20 C C 87832-1011 87832-1009 87832-1007 1 3 87832-1004 N.A N.A N.A 2 N.A YES YES N.A YES 0.10 3.60±0.20 87832-1260 87832-1262 87832-5562 1 1 87832-1220 87832-1222 87832-5522 1 2 87832-5523 1 N.A N.A YES YES YES 0.10 3.60±0.20 87832-1221 87832-1223 3 87832-9623 2 87832-1270 87832-1272 87832-5572 1 4 12 87832-1224 87832-1226 87832-1228 1 2 14.65 12.85 10.00 N.A 8.00 13.00 N.A YES YES N.A N.A 0.10 3.60±0.15 87832-1225 87832-1227 87832-1229 1 3 B B 87832-1210 87832-1208 87832-1206 1 2 N.A YES YES N.A YES 0.10 3.60±0.20 87832-1211 87832-1209 87832-1207 1 3 87832-1204 N.A N.A N.A 2 N.A YES YES N.A YES 0.10 3.60±0.20 87832-1212 N.A N.A N.A 2 N.A N.A YES YES N.A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE PLATING OPTIONS: GENERAL TOLERANCES (UNLESS SPECIFIED) MM NTS 1 - 0.05-0.13µm/2-5µin GOLD IN CONTACT AREA AND DRWN BY DATE 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER MM INCH 1.27µm/50µin MIN. NICKEL OVERALL. 4 PLACES ± ± GMENARLY 2015/05/22 MILLIGRID 2 - 0.38µm/15µin MIN. GOLD IN CONTACT AREA AND 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 2 PLACES ± 0.2 ± A 1.27µm/50µin MIN. NICKEL OVERALL. CGOH 2015/09/21 A 1 PLACES ± ± 3 - 0.76µm/30µin MIN. GOLD IN CONTACT AREA AND APPR BY DATE PRODUCT CUSTOMER DRAWING 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 0 PLACES ± ± KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER 1.27µm/50µin MIN. NICKEL OVERALL. ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION 4 - 2.50µm/100µin MIN. MATTE TIN OVER 1.25µm/50µin MIN. NICKEL OVERALL. GENERAL MARKET 87832 SEE TABLE DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 7 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 14 TO 50 CIRCUITS A 4.60 6.35 B ⌖ 0.50 Y RIBS LOCATIONS VARY DEPENDING ON CKT SIZES C CKT #2 E E ⌀0.71±0.05 TYP �9.05� 2.00 4.50 5.00 6.30 CKT #1 ℄ OF C C/2 2.00 TYP DETAIL 4 VIEW FOR HEADER WITH CAP DETAIL 4 D CIRCUIT IDENTIFICATION W D D �3.90� H 4.70 6.40 7.60 6 G (COPLANARITY) 1.20 TYP W 2.20 (2X) E C/2 0.50±0.05 SQ ℄ OF C 2.00 TYP TYP ISO VIEW OF HEADER WITH CENTER SECTION W-W C C POLARIZATION AND DUAL SIDE SLOTS ⌀0.85±0.08 (2X) E (5.30) 1.00 2.00 �0.65� TYP (TYP) (TYP) TYP ⌀1.00±0.05 (2X) 1.50 RIBS LOCATIONS VARY DEPENDING ON CKT SIZES & FEATURES 2.13 C 2.75 (TYP) B B F NOTES: C/2 1. MATERIALS: ℄ OF C 1.00 HOUSING & CAP: 30% GF, NYLON, UL94V-0, COLOR: BLACK C PIN: 0.50mm SQ. PHOSPHOR BRONZE RECOMMENDED PCB LAYOUT 2. FINISHES: REFER TO PLATING OPTIONS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 3. PRODUCT SPECIFICATION: PS-87831-027 DIMENSION UNITS SCALE GENERAL TOLERANCES 4. PACKAGING SPECIFICATION: SEE PACKAGING SPECS TABLE ON SHEET 12 (UNLESS SPECIFIED) MM NTS 5. MATES WITH: A. MOLEX CRIMP RECEPTACLE HOUSING: 51110 SERIES DRWN BY DATE MM INCH AND CRIMP TERMINAL: 50394 SERIES B. MOLEX 2mm MILLIGRID DUAL ROW IDT: 87568 SERIES 4 PLACES ± ± GMENARLY 2015/05/22 MILLIGRID C. MOLEX 2mm MILLIGRID DUAL ROW RECEPTACLE: 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 79107 (GOLD PLATED), 78787 (TIN PLATED) 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A 6 COPLANARITY IS TO BE MEASURED BY RESTING THE SOLDERTAIL ON 1 PLACES ± ± APPR BY DATE A GAUGE SURFACE PRODUCT CUSTOMER DRAWING 0 PLACES ± ± 7. BEND DEPRESSION ON SMT TAIL IS ACCEPTABLE SO LONG AS IT KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER DOES NOT AFFECT THE OVERALL COPLANARITY ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION GENERAL MARKET 8. TOP SURFACE OF CAP TO BE FLAT FOR THE PURPOSE OF 87832 SEE TABLE DRAFT WHERE APPLICABLE PICK & PLACE BY VACUUM SUCTION NOZZLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 8 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 14 TO 24 CIRCUITS T&R FRICTION LOCKS DIMENSION DUAL ASSY P/N ASSY P/N ASSY P/N CKT OPTIONS PLATING CENTER WITHOUT CAP WITH CAP WITH CAP SIDE PEGS G SIZE (SEE OPTIONS POLARIZATION DUAL CENTER A B C D E F H IN TUBE IN TUBE IN T&R SLOTS (COPLAN) SHEET 12) E E 87832-1460 87832-1462 87832-5662 1 1 87832-1420 87832-1422 87832-5622 1 2 87832-5623 1 YES N.A YES YES YES 0.15 3.60±0.20 14 87832-1421 87832-1423 3 16.65 14.85 12.00 8.00 10.00 15.00 87832-9523 2 87832-1470 87832-1472 87832-5672 1 4 87832-1412 87832-1416 87832-1414 1 2 YES N.A YES YES N.A 0.15 3.60±0.20 87832-1660 87832-1662 87832-5762 1 1 87832-1620 87832-1622 87832-5722 1 2 YES N.A YES YES YES 0.15 3.60±0.20 16 87832-1621 87832-1623 87832-5723 1 3 18.65 16.85 14.00 10.00 12.00 17.00 87832-1670 87832-1672 87832-5772 1 4 87832-1612 87832-1616 87832-1614 1 2 YES N.A YES YES N.A 0.15 3.60±0.20 D D 87832-1860 87832-1862 87832-5862 1 1 87832-1820 87832-1822 87832-5822 1 2 YES N.A YES YES YES 0.15 3.60±0.20 87832-1821 87832-1823 87832-5823 1 3 18 20.65 18.85 16.00 12.00 14.00 19.00 87832-1870 87832-1872 87832-5872 1 4 87832-1812 87832-1816 87832-1814 3 2 YES N.A YES YES N.A 0.15 3.60±0.20 87832-1813 87832-1817 87832-1815 3 3 YES N.A YES YES N.A 0.15 3.60±0.20 87832-2060 87832-2062 87832-5962 1 1 87832-2020 87832-2022 87832-5922 1 2 87832-2021 87832-2023 87832-5923 1 3 YES N.A YES YES YES 0.15 3.60±0.20 20 22.65 20.85 18.00 14.00 16.00 21.00 C C 87832-5972 1 87832-2070 87832-2072 4 87832-9672 2 87832-2012 87832-2016 87832-2014 1 2 YES N.A YES YES N.A 0.15 3.60±0.20 87832-2260 87832-2262 87832-6062 1 1 87832-2220 87832-2222 87832-6022 1 2 22 YES N.A YES YES YES 24.65 22.85 20.00 16.00 18.00 23.00 0.15 3.60±0.20 87832-2221 87832-2223 87832-6023 1 3 87832-2270 87832-2272 87832-6072 1 4 87832-2460 87832-2462 87832-6162 1 1 87832-2420 87832-2422 87832-6122 1 2 YES N.A YES YES YES 0.15 3.60±0.20 B B 24 87832-2421 87832-2423 87832-6123 1 3 26.65 24.85 22.00 18.00 20.00 25.00 87832-2470 87832-2472 87832-6172 1 4 87832-2412 87832-2416 87832-2414 1 2 YES N.A YES YES N.A 0.15 3.60±0.20 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES (UNLESS SPECIFIED) PLATING OPTIONS: MM NTS 1 - 0.05-0.13µm/2-5µin GOLD IN CONTACT AREA AND DRWN BY DATE MM INCH 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 4 PLACES ± ± GMENARLY 2015/05/22 1.27µm/50µin MIN. NICKEL OVERALL. MILLIGRID 3 PLACES ± ± CHK'D BY DATE 2 - 0.38µm/15µin MIN. GOLD IN CONTACT AREA AND 2MM PITCH, SMT VERTICAL SHROUDED HEADER 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A 1.27µm/50µin MIN. NICKEL OVERALL. 1 PLACES ± ± APPR BY DATE PRODUCT CUSTOMER DRAWING 3 - 0.76µm/30µin MIN. GOLD IN CONTACT AREA AND 0 PLACES ± ± KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER ANGULAR TOL ± 3.0 DRAWING SIZE 1.27µm/50µin MIN. NICKEL OVERALL. THIRD ANGLE PROJECTION GENERAL MARKET 87832 SEE TABLE 4 - 2.50µm/100µin MIN. MATTE TIN OVER 1.25µm/50µin MIN. NICKEL OVERALL. DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 9 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 26 TO 38 CIRCUITS T&R FRICTION LOCKS DIMENSION DUAL ASSY P/N ASSY P/N ASSY P/N CKT OPTIONS PLATING CENTER WITHOUT CAP WITH CAP WITH CAP SIDE PEGS G SIZE (SEE OPTIONS POLARIZATION DUAL CENTER A B C D E F H IN TUBE IN TUBE IN T&R SLOTS (COPLAN) SHEET 12) E E 87832-2660 87832-2662 87832-6262 1 1 87832-2620 87832-2622 87832-6222 1 2 YES N.A YES YES YES 0.15 3.60±0.20 26 87832-2621 87832-2623 87832-6223 1 3 28.65 26.85 24.00 20.00 22.00 27.00 87832-2670 87832-2672 87832-6272 1 4 87832-2612 87832-2616 N.A N.A 2 YES N.A YES YES N.A 0.15 3.60±0.20 87832-2860 87832-2862 87832-6362 1 1 87832-2820 87832-2822 87832-6322 1 2 YES N.A YES YES YES 87832-2821 87832-2823 87832-6323 1 3 28 30.65 28.85 26.00 22.00 24.00 29.00 0.15 3.60±0.20 87832-2870 87832-2872 87832-6372 1 4 N.A 87832-2816 N.A 1 2 YES N.A YES YES N.A N.A 87832-2819 N.A 1 1 D D 87832-3060 87832-3062 87832-6462 1 1 87832-3020 87832-3022 87832-6422 1 2 YES N.A YES YES YES 0.15 3.60±0.20 30 87832-3021 87832-3023 87832-6423 1 3 32.65 30.85 28.00 24.00 26.00 31.00 87832-3070 87832-3072 87832-6472 1 4 87832-3012 87832-3016 87832-3014 3 2 YES N.A YES YES N.A 0.15 3.60±0.20 87832-3260 87832-3262 87832-6562 1 1 87832-3220 87832-3222 87832-6522 1 2 32 YES N.A YES YES YES 34.65 32.85 30.00 26.00 28.00 33.00 0.15 3.60±0.20 87832-3221 87832-3223 87832-6523 1 3 87832-3270 87832-3272 87832-6572 1 4 C C 87832-3460 87832-3462 87832-6662 1 1 87832-3420 87832-3422 87832-6622 1 2 YES N.A YES YES YES 0.15 3.60±0.20 34 87832-3421 87832-3423 87832-6623 1 3 36.65 34.85 32.00 28.00 30.00 35.00 87832-3470 87832-3472 87832-6672 1 4 87832-3412 87832-3416 87832-3414 3 2 YES N.A YES YES N.A 0.15 3.60±0.20 87832-3660 87832-3662 N.A N.A 1 87832-3620 87832-3622 N.A N.A 2 36 YES N.A YES YES YES 38.65 36.85 34.00 30.00 32.00 37.00 0.15 3.60±0.20 87832-3621 87832-3623 N.A N.A 3 N.A N.A 4 87832-3670 87832-3672 B B 87832-3860 87832-3862 N.A N.A 1 87832-3820 87832-3822 87832-6822 N.A 2 38 YES N.A YES YES YES 40.65 38.85 36.00 32.00 34.00 39.00 0.15 3.60±0.20 87832-3821 87832-3823 N.A N.A 3 87832-3870 87832-3872 N.A N.A 4 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES PLATING OPTIONS: (UNLESS SPECIFIED) MM NTS 1 - 0.05-0.13µm/2-5µin GOLD IN CONTACT AREA AND DRWN BY DATE MM INCH 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 4 PLACES ± ± GMENARLY 2015/05/22 1.27µm/50µin MIN. NICKEL OVERALL. MILLIGRID 2 - 0.38µm/15µin MIN. GOLD IN CONTACT AREA AND 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A 1.27µm/50µin MIN. NICKEL OVERALL. 1 PLACES ± ± APPR BY DATE 3 - 0.76µm/30µin MIN. GOLD IN CONTACT AREA AND PRODUCT CUSTOMER DRAWING 0 PLACES ± ± KHLIM 2015/09/22 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER SERIES MATERIAL NUMBER CUSTOMER ANGULAR TOL ± 3.0 1.27µm/50µin MIN. NICKEL OVERALL. DRAWING SIZE THIRD ANGLE PROJECTION GENERAL MARKET 87832 SEE TABLE 4 - 2.50µm/100µin MIN. MATTE TIN OVER 1.25µm/50µin MIN. NICKEL OVERALL. DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 10 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 40 TO 50 CIRCUITS T&R FRICTION LOCKS DIMENSION DUAL ASSY P/N ASSY P/N ASSY P/N CKT OPTIONS PLATING CENTER WITHOUT CAP WITH CAP WITH CAP SIDE PEGS G SIZE (SEE OPTIONS POLARIZATION E E DUAL CENTER A B C D E F H IN TUBE IN TUBE IN T&R SLOTS (COPLAN) SHEET 12) 87832-4060 87832-4062 87832-6962 1 1 87832-4020 87832-4022 87832-6922 1 2 YES N.A YES YES YES 0.15 3.60±0.20 40 87832-4021 87832-4023 87832-6923 1 3 42.65 40.85 38.00 34.00 36.00 41.00 87832-4070 87832-4072 87832-6972 1 4 87832-4012 87832-4016 N.A N.A 2 YES N.A YES YES N.A 0.15 3.60±0.20 87832-4260 87832-4262 N.A N.A 1 87832-4220 87832-4222 N.A N.A 2 42 YES N.A YES YES YES 44.65 42.85 40.00 36.00 38.00 43.00 0.15 3.60±0.20 87832-4221 87832-4223 N.A N.A 3 87832-4270 87832-4272 N.A N.A 4 87832-4460 87832-4462 87832-7162 1 1 D D 87832-4420 87832-4422 87832-7122 1 2 YES N.A YES YES YES 0.15 3.60±0.20 44 87832-4421 87832-4423 87832-7123 1 3 46.65 44.85 42.00 38.00 40.00 45.00 87832-4470 87832-4472 87832-7172 1 4 87832-4413 87832-4417 87832-4415 3 3 YES N.A YES YES N.A 0.15 3.60±0.20 87832-4660 87832-4662 87832-7262 1 1 87832-4620 87832-4622 87832-7222 1 2 46 YES N.A YES YES YES 48.65 46.85 44.00 40.00 42.00 47.00 0.15 3.60±0.20 87832-4621 87832-4623 N.A N.A 3 87832-4670 87832-4672 87832-7272 1 4 87832-4860 87832-4862 N.A N.A 1 C C 87832-4820 87832-4822 N.A N.A 2 48 YES N.A YES YES YES 50.65 48.85 46.00 42.00 44.00 49.00 0.15 3.60±0.20 87832-4821 87832-4823 N.A N.A 3 N.A N.A 4 87832-4870 87832-4872 87832-5060 87832-5062 87832-7462 1 1 87832-5020 87832-5022 87832-7422 1 2 YES N.A YES YES YES 0.15 3.60±0.20 50 87832-5021 87832-5023 87832-7423 1 3 52.65 50.85 48.00 44.00 46.00 51.00 87832-5070 87832-5072 87832-7472 1 4 87832-5012 87832-5016 N.A N.A 2 YES N.A YES YES N.A 0.15 3.60±0.20 B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES (UNLESS SPECIFIED) MM NTS PLATING OPTIONS: 1 - 0.05-0.13µm/2-5µin GOLD IN CONTACT AREA AND DRWN BY DATE MM INCH 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER 4 PLACES ± ± GMENARLY 2015/05/22 MILLIGRID 1.27µm/50µin MIN. NICKEL OVERALL. 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 2 - 0.38µm/15µin MIN. GOLD IN CONTACT AREA AND 2 PLACES ± 0.2 ± A 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER CGOH 2015/09/21 A 1 PLACES ± ± 1.27µm/50µin MIN. NICKEL OVERALL. APPR BY DATE PRODUCT CUSTOMER DRAWING 3 - 0.76µm/30µin MIN. GOLD IN CONTACT AREA AND 0 PLACES ± ± KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER 1.88µm/75µin MIN. MATTE TIN IN SOLDER TAIL AREA OVER ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION 1.27µm/50µin MIN. NICKEL OVERALL. GENERAL MARKET 87832 SEE TABLE DRAFT WHERE APPLICABLE 4 - 2.50µm/100µin MIN. MATTE TIN OVER 1.25µm/50µin MIN. NICKEL OVERALL. MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 11 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03 9 8 7 6 5 4 3 2 1 PACKAGING OPTIONS E E OPTION 1 OPTION 3 OPTION 2 D D CUSTOMER CUSTOMER CUSTOMER PULL OUT DIRECTION PULL OUT DIRECTION PULL OUT DIRECTION C C PACKAGING SPECIFICATION TABLE VIEW FOR 1 SIDE PILOT HOLE EMBOSSED TAPE & REEL POCKET DESCRIPTIONS TAPE AND REEL PACKAGING PK-87832-300 TUBE STANDARD PACKAGING PK-87831-001 CENTER POLARIZATION OPTIONS PEG OPTIONS PILOT HOLE OPTIONS TUBE NON-STANDARD PACKAGING FOR: OPTIONS ON THE LEFT ON THE RIGTH WITH PEG WITHOUT PEG 2 SIDES 1 SIDE B B 87832-0411 1 YES N.A YES N.A CKT 12-50 CKT 4-10 87832-0824 PK-87831-002 2 N.A YES YES YES CKT 12-50 CKT 4-10 87832-1072 87832-1412 3 YES N.A N.A YES CKT 12-50 CKT 4-10 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES (UNLESS SPECIFIED) MM NTS CUSTOMER DRWN BY DATE MM INCH PULL OUT DIRECTION 4 PLACES ± ± GMENARLY 2015/05/22 MILLIGRID 3 PLACES ± ± CHK'D BY DATE 2MM PITCH, SMT VERTICAL SHROUDED HEADER 2 PLACES ± 0.2 ± A CGOH 2015/09/21 A 1 PLACES ± ± APPR BY DATE PRODUCT CUSTOMER DRAWING 0 PLACES ± ± KHLIM 2015/09/22 SERIES MATERIAL NUMBER CUSTOMER ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION GENERAL MARKET 87832 SEE TABLE DRAFT WHERE APPLICABLE MUST REMAIN DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER A3 WITHIN DIMENSIONS A9 12 OF 12 SD-87832-0001 PSD 001 RELEASE STATUS P1 RELEASE DATE 2018/07/03 05:11:29 FORMAT: Met-lega-master-tb-prod-A3 REVISION: C 9 8 7 6 5 4 3 2 1 DATE: 2017/02/06 SH7: ADD 87832-9623 EC NO: 178404 DRWN: SCS02 2018/06/25 CHK'D: GJEEVANSURES 2018/06/26 REV APPR: ISHWARG 2018/07/03