D1U4-W-1600-54-HBxC www.murata-ps.com AC-DC Power Supply PRODUCT OVERVIEW The D1U4-W-1600-54-HBxC is a 1600W power factor corrected (PFC) front end power module intended for hot swap redundant systems. There is a main output of 54VDC (fl oating with respect to chassis ground) and a 12VDC Standby/ bias output (that is present whenever the incoming AC source is applied. The form factor is suitable for 1RU chassis enclosures and is designed to deliver reliable bulk DC power to servers, workstations, storage systems, PoE switches or any 54VDC distributed power architecture requiring high power density. The high effi ciency design supports speed controlled dual DC fans in a thermally optimized package that is self-pro- tecting and able to auto recover from over-current and over-temperature events. Visual status information is provided via front panel mounted LED indicators in addition to hardware logic signals and a PMBus™ management interface. ORDERING GUIDE Power Output High Power Output Low Standby Model Number Main Output Airfl ow Line AC Line AC Output D1U4-W-1600-54-HB4C Back to front 1600W 1200W 54V 12V D1U4-W-1600-54-HB3C Front to back FEATURES  1600W Output Power INPUT CHARACTERISTICS  1.6"(1U) x 14.0" x 4.0" Parameter Conditions Min. Typ. Max. Units (41.0mm x 355.6mm x 101.6mm) Input Voltage Operating Range 90 115/230 264 Vac Input Frequency 47 50/60 63 Hz  54VDC Main; PoE compatible Turn-on Input Voltage Ramp Up 81 89  12V SB Output Vac Turn-off Input Voltage Ramp Down 70.5 78.0  PMBus™ Power Management Bus supported by Maximum Current @ VIN = 200Vac 1600W 10 Arms dual redundant I2C interfaces. Maximum Current @ VIN = 90Vac 1200W 15  N+1 Redundancy Capable; hot swap (up to 8 Inrush Current Cold start between 0 to 1ms 100 Apk modules in parallel) Power Factor At 230Vac; FL 0.95  Active current sharing on 54VDC Main output; OUTPUT VOLTAGE CHARACTERISTICS integral bidirectional MOSFET output isolation Output device Parameter Conditions Min. Typ. Max. Units Voltage  Over-Voltage, Over-Current; Over-Temperature Voltage Set Point 54V Vdc Protection Line & Load Regulation 52.38 55.62  Internal variable speed cooling fans 54V Output Current 0 30 A 1 Ripple Voltage & Noise 20MHz Bandwidth 540 mVp-p  20ms full cycle hold up Load Capacitance 3800 24,000 µF  RoHS Compliant Voltage Set Point 12 Vdc  Two-year warranty Line & Load Regulation 11.64 12.36 12V Output Current 0 2 A 1 Ripple Voltage & Noise 20MHz Bandwidth 33 mVp-p Load Capacitance 1530 µF 1 Ripple and noise are measured with a parallel combination of a 0.1µF ceramic capacitor and 2 x 270µF OSCON capacitors on each of the power module outputs measurement nodes. See test set up diagram below. www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html Available now at www.murata-ps.com/en/3d/acdc.html CB For full details go to Test Certifi cate PM www.murata-ps.com/rohs and Test Report www.murata-ps.com/support CPS_D1U4-W-1600-54-HBxC.B03 Page 1 of 6 D1U4-W-1600-54-HBxC AC-DC Power Supply RIPPLE MEASUREMENT 0.1uF Ceramic 2x270uF OSCON Power Supply Load Box AC Phase AC Ground BNC to BNC Shielded Cable General Notes: 1. Load the outputs at specified minimum output current. Oscilloscope 2. Connect the probe as shown with the 20MHz BW input tip and ground as short as possible. 3. Take all measurements 4. Repeat the measurements with the outputs at specified maximum output current. OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Remote sense is not enabled on these variants due to the System Control feature and the relatively wide line & Remote Sense load regulation window. Efficiency 230Vac (excluding fan) 90 % Overshoot less than 10% for all outputs; no negative transition at Output Rise (Monotonic) 10% to 95% rise time turn off. AC Ramp Up 3 s Startup Time PS_ON activation 250 ms 54VDC 50% step (50-100%; 100%-50%) ±2700 load; 1A/µs Transient Response mV 12VSB 1A/µs ±250 Current Sharing Accuracy (up to 8 in parallel) At 100% load ±10 % Hot Swap Transients 5 % Hold Up Time 100% load 230Vac nominal 20 ms ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range Non-Condensing -40 70 °C Operating Temperature Range 0 50 Operating Humidity Non-Condensing 10 90 % Storage Humidity 5 90 Altitude 3000 M Shock Non-Operating 30 G Operational Vibration Operational, 0.5G; 5-500Hz MTBF Telcordia SR-332 40°C 630 K Hours CAN/CSA-C22.2 No.60950-1-07 Am 1:2011 ANSI/UL 60950-1-2011 Safety Approvals IEC60950-1:2005 (2nd Ed)+A1:2009 and EN60950-1:2006/A11:2009/A1:2010/A12:2011 CQC GB4943,1-2011 Input Fusing Internal 20A/250V rated fast blow in AC line Weight 4.63/2.1 lbs/kg www.murata-ps.com/support CPS_D1U4-W-1600-54-HBxC.B03 Page 2 of 6 D1U4-W-1600-54-HBxC AC-DC Power Supply PROTECTION CHARACTERISTICS Output Parameter Conditions Min. Typ. Max. Units Voltage Over-Temperature Auto re-start 55 65 °C 54V Over-Voltage Latching 57 60 V Constant Current for 200ms Over-Current 33 39 A followed by latch Over-Voltage Latching 13.5 14.4 V 12VSB Over-Current Latching 2.2 2.6 A ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Input to Output - Reinforced 3000 Vrms Insulation Safety Rating / Test Voltage Input to Chassis - Basic 1500 Vrms Isolation Output to Chassis (Ground) 2250 Vdc The Main 54VDC output shall be provided with isolation between the output and chassis ground. It shall be able to withstand the following tests: a) 1500VRMS at 50Hz to 60Hz for 60s. b) 2250 VDC for 60s. Grounding There shall be no insulation breakdown during the test as defined in sub clause 5.2.2 of IEC 60950-1:2001. The resistance after the test should be at least 2M ohms when measured at 500VDC. The VRTN should be isolated from the 12VSB Return and the power module shall support PoE Electrical Isolation Requirements. STATUS INDICATORS AND CONTROL SIGNALS Status Conditions Description Off No AC applied to any power module in host system Off No AC applied to this power module only Blinking Green AC Present & VSTANDBY “on” LED Indicators Green 54VDC and VSTANDBY “on” and “OK” Blinking Amber Power Module Warning Amber Power Module Failure There is provision for the connection of dual I2C buses for redundancy. This enables two master devices to connect to single slave device(s) within the power module. 2 I C and PMBus The power module is provided with a PMBus Management Interface that provides status, measurement and control data. SYS_CONTR Host system control input that can be used to turn on/off the Main 54VDC Output. EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics IEC/EN 61000-3-2 Complies with Class A Limits Voltage Fluctuation & Flicker IEC/EN 61000-3-3 Complies Conducted Emissions FCC 47 CFR Part 15; CISPR 22; EN55022 Complies to Class A with 6dB margin Radiated Emissions Complies to Class A with 6dB margin 4KV Contact discharge; Criteria A ESD Immunity IEC/EN 61000-4-2; 8KV Operational air discharge; Criteria A 15KV non-operational air discharge, Criteria A Radiated Field Immunity IEC/EN 61000-4-3 Complies Electrical Fast Transients/Burst Immunity IEC/EN 61000-4-4 Complies Surge Immunity IEC/EN 61000-4-5 1KV/2KV; Criteria A performance RF Conducted Immunity IEC/EN 61000-4-6 3VAC, 80% AM, 1KHz; Criteria A performance Magnetic Field Immunity IEC/EN 61000-4-8 3A/m Voltage Dips & Interruptions IEC/EN 61000-4-11 Complies www.murata-ps.com/support CPS_D1U4-W-1600-54-HBxC.B03 Page 3 of 6 D1U4-W-1600-54-HBxC AC-DC Power Supply OUTPUT CONNECTOR AND SIGNAL SPECIFICATION DC and Signal Connector: FCI # 51732-028-LF P1 P2 P3 P4 P5 P6 x1 x2 x3 x4 x5 No User V_STBY AC_OK P_GOOD V_STBY D Connection RETURN V_STBY V_STBY PS_ON V_STBY V_STBY C RETURN RETURN VOUT VOUT VOUT VRTN VRTN VRTN 2 2 I_SHARE SYS_CONTR I C DATA2 I C CLOCK2 PS_PRESENT B 2 2 PS_KILL Vout SENSE+ Vout SENSE- I C DATA1 I C CLOCK1 A Blade/ Pin Assignment Signal Name Description Logic Level Current P1, P2, P3 VOUT Main 54V Output Voltage P4, P5, P6 VRTN Main 54V Output Voltage, Return A2 VOUT_SENSE + Main 54V Output Voltage Sense + A3 VOUT_SENSE - Main 54V Output Voltage Sense - C2, C3, D3 VSTBY Standby Voltage Output C4, C5, D5 VSTBY Return Standby Voltage Output, Return B1 I_SHARE Analogue active current share bus 0V to 8V -4mA/+5mA AC Source Voltage OK Signal (Internally pull up to VSTANDBY by 10KΩ (3.3V & 5V >2.4V (Active, OK) +4mA D1 AC_OK VSTANDBY). <0.4V (not OK) -2mA 10KΩ (to 5V) for 12 VSTANDBY Power Good Signal (Internally pull up to VSTANDBY by 10KΩ (3.3V & 5V >2.4V (Active, GOOD) +4mA D2 P_GOOD <0.4V (not GOOD) -2mA VSTANDBY). 10KΩ (to 5V) for 12 VSTANDBY >2.4V “high” A1 PS_KILL Floating pin; will turn off main output <0.4V “low” B5 PS_PRESENT Tied internally to VSTANDBY Return 0V Internally pull up to VSTANDBY by 1KΩ; can be driven with >2.4V “high” C1 PS_ON_L open drain/collector switches <0.4V “low” 2 2 A4 I C_SDA0 (SDA) I C compatible Data Bus 2 2 A5 I C_SCL0 (SCL) I C compatible Data Bus 2 2 B3 I C_SDA1 (SDA) I C compatible Data Bus >2.4V “high” 2 2 B4 I C_SCL1 (SCL) I C compatible Data Bus <0.4V “low” Host system control that can be used to turn on/off the Main B2 SYS_CONTR 54V DC Output via an internal output switch within power module. Low turns “on” output switch MATING CONNECTOR Supplier Press Fit, Straight Press Fit, Right Angle Solder Straight Solder Right Angle FCI -- -- -- 51762-1060-2000-ABLF www.murata-ps.com/support CPS_D1U4-W-1600-54-HBxC.B03 Page 4 of 6 D1U4-W-1600-54-HBxC AC-DC Power Supply WIRING DIAGRAM FOR OUTPUT - Dotted lines show optional remote sense connections. Optional remote sense lines can be attached to a load that is a distance away from the power supply to improve regulation at the load. Sense + (Main Output Remote Sense) Sense + (Main Output Remote Sense) VOUT VOUT A2 A2 P1, P2, P3 P1, P2, P3 54V Load D1U4 D1U4 P4, P5, P6 VRTN P4, P5, P6 VRTN Sense - Sense - A3 A3 I_Share B1 B1 I_Share Vstby Vstby C2, C3, D3 C2, C3, D3 PS_On_L PS_On_L C1 C1 12V Standby Load Close Switch (or FET, BJT or wire) to turn on +54V OUT C4, C5, D5 Vsb Return Vsb Return C4, C5, D5 A1 PS_Kill A1 PS_Kill CURRENT SHARING NOTES 1. Main 54VDC Output: Analogue active share bus. The ISHARE bus (Pin B1) must be connected on all sharing modules. It is not required that the SENSE signals are connected to the remote load for current share to operate correctly. 2. Up to eight (8) power modules can be connected in parallel (non-redundant) or N+1 configuration. The current share bus is analogue bi-directional (can source or sink current from the ISHARE bus). The voltage of the bus would measure 8VDC for a single power module at 100% load; for two (2) modules sharing a common load the ISHARE bus voltage would be 4V for a perfect 50/50 current share scenario. 3. VSTANDBY output power modules can also be connected in parallel; however the combined available power is limited to that available from a single power module (12V; 2A; 24W) irrespective of the number of modules connected in parallel. www.murata-ps.com/support CPS_D1U4-W-1600-54-HBxC.B03 Page 5 of 6 D1U4-W-1600-54-HBxC AC-DC Power Supply MECHANICAL DIMENSIONS BACK TO FRONT AIRFLOW FRONT TO BACK AIRFLOW 13.25 ±0.40 12.63 ±0.50 349.60 ±0.65 10.75 ±0.40 8.88 ±0.40 ALL DIMENSIONS IN MM 355.60 ±0.65 AC Input Connector/Inlet: IEC 60320-C20 Dimensions: 4.00" x 14.00"x 1.6" [101.6mm x 355.6mm x 41.0mm] OPTIONAL ACCESSORIES Description Part Number D1U4-54 Output Interface Connector Card D1U4-54-CONC APPLICATION NOTES Document Number Description Link ACAN-52 D1U4-54-CONC Output Connector Card www.murata-ps.com/data/apnotes/acan-52.pdf ACAN-53 D1U4 Communications Protocol www.murata-ps.com/data/apnotes/acan-53.pdf This product is subject to the following operating requirements Murata Power Solutions, Inc. and the Life and Safety Critical Application Sales Policy: 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Refer to: http://www.murata-ps.com/requirements/ ISO 9001 and 14001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2017 Murata Power Solutions, Inc. www.murata-ps.com/support CPS_D1U4-W-1600-54-HBxC.B03 Page 6 of 6 21.45 ±0.50 2.40 ±0.35 41.00 ±0.40 101.60 ±0.50