D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter PRODUCT OVERVIEW The D1U54P-W-1200-12-HxxPC series are very high efficiency 1200 watt, power factor corrected front end supply with a 12V main output and a 5V or 3.3V (3A) standby. They have active current sharing and up to 8 supplies may be operated in parallel. The supply may be hot plugged; recovers from overtemperature faults, and has status LEDs on the front panel in addition to logic and PMBus™ status signals. The low profile 1U package and >28W/cubic inch power density make it ideal for delivering reliable, efficient power to servers, workstations, storage systems and other 12V distributed power systems ORDERING GUIDE Power Output IEC 320-C16 Main Standby Part Number Airflow Input Connector 200-240Vac 100-120Vac Output Output Option D1U54P-W-1200-12-HC4PC 3.3Vdc Back to Front 1 D1U54P-W-1200-12-HA4PC 5Vdc HA4PTC 1200W 1100W 12Vdc D1U54P-W-1200-12-HC3PC 3.3Vdc Front to Back 1 D1U54P-W-1200-12-HA3PC 5Vdc HA3PTC 1. Refer to Pg. 9 for alternate input connector (HAxPTC) 2. ® The HAxPC variants are certified for compliance to 80 PLUS INPUT CHARACTERISTICS FEATURES Parameter Conditions Min. Nom. Max. Units  1200W output power Input Voltage Operating Range 90 115/230 264 Vac ® Input Frequency 47 50/60 63 Hz  80 PLUS Platinum efficiency Turn-on Input Voltage Ramp up 80 85 89 Vac  12V main output Turn-off Input Voltage Ramp down 65 73 78  3.3V and 5V standby output Maximum current at Vin = 100Vac 1100W 12 Arms Inrush Current Cold start between 0 to 200msec 25 Apk  1U height: 2.15" x 12.65" x 1.57" Power Factor At 230Vac, full load 0.99  >28 Watts per cubic inch density 20% load 90 Efficiency (230Vac) excluding fan load 50% load 94 %  N+1 redundancy capable, 100% load 91 including hot plugging (up to 8 in parallel)  Active current sharing on 12V main output; both OUTPUT VOLTAGE CHARACTERISTICS outputs contain ORing FET isolation Nominal Output Parameter Conditions Min. Typ. Max. Units  Overvoltage, overcurrent, overtemperature Voltage protection Nominal Output Voltage 12 Vdc  Internal cooling fan (variable speed) Output Set Point Accuracy 50% load; Tamb =25°C -0.5 +0.5 %  PMBus™ / I²C interface with status indicators Line and Load Regulation -1.0 +1.0 3 12V Ripple Voltage & Noise 20MHz Bandwidth 150 mV p-p  RoHS compliant Output Current (230Vac) 5 100  Two-year warranty A Output Current (120Vac) 5 90 Load Capacitance 0 30,000 μF Nominal Output Voltage 3.3 Vdc Line and Load Regulation 3.14 3.46 3 3.3VSB Ripple Voltage & Noise 20MHz Bandwidth 75 mV p-p Output Current 0 3 A www.murata-ps.com/en/3d/acdc.html Load Capacitance 0 1000 μF www.murata-ps.com/en/3d/acdc.html Nominal Output Voltage 5.0 Vdc www.murata-ps.com/en/3d/acdc.html Line and Load Regulation 4.76 5.24 www.murata-ps.com/en/3d/acdc.html 12 5VSB Ripple Voltage & Noise 20MHz Bandwidth 75 mV p-p www.murata-ps.com/en/3d/acdc.html Output Current 0 3 A www.murata-ps.com/en/3d/acdc.html Load Capacitance 0 1000 μF 3 Ripple and noise are measured with 0.1 μF of ceramic capacitance and 10 μF of tantalum capacitance on each of the power supply outputs. A short coaxial cable with 50Ω scope termination is used. Available now at: www.murata-ps.com/en/3d/acdc.html For full details go to www.murata-ps.com/rohs . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 1 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Startup Time AC ramp up 3 s 12V, 50% load step, 1A/μs di/dt ±5 Transient Response % VSB, 50% load step, 1A/μs di/dt ±5 1 Current sharing accuracy (up to 8 in parallel) At 100% load ±7 % Hot Swap Transients All outputs remain in regulation 5 % Holdup Time 100% load 12 ms ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range -40 70 °C Operating Temperature Range 0 60 Operating Humidity Noncondensing 5 90 % Storage Humidity 5 95 Altitude (without derating at 40°C) 3000 m Shock 30G non-operating Sine sweep; 5-150Hz, 2G; Operational Vibration random vibration, 5-500Hz, 1.11G MTBF Per Telcordia SR-332 M1C1 @40°C 529K hrs CAN/CSA C22.2 No 60950-1-07, Amendment 1:2011, Amendment 2:2014 (MOD) ANSI/UL 60950-1-2014 IEC60950-1:2005 (2nd ED.)+A1:2009+A2:2013 EN60950-1:2006+A11+A1+A12+A2 CCC GB4943.1-2011, GB9254-2008, GB17625. 1-2012 Safety Approval Standards BSMI CNS14336-1; CNS13438 Input Fuse Power Supply has internal 15A/250V fast blow fuse on the AC line input Weight 2.43 lbs (1.10 kg) PROTECTION CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units Overtemperature (intake) Autorestart 70 80 °C Overvoltage Latching 13 14 V Overcurrent At 220Vac Hiccup 105 120 12V A 4 Overcurrent At 110Vac Hiccup 99 117 A Overvoltage Latching 3.6 4.0 V 3.3VSB Overcurrent Hiccup 3.3 4.5 A Overvoltage Latching 5.4 6.0 V 5VSB Overcurrent Hiccup 3.3 4.5 A 4 An output overload condition that caused the input current to exceed 13Aac shall initiate a latching shutdown. It will be necessary to recycle the ac input source in order to clear the latched condition. ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Input to Output - Reinforced 3000 Vrms Insulation Safety Rating / Test Voltage Input to Chassis - Basic 1500 Vrms Isolation Output to Chassis 500 Vdc . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 2 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter STATUS INDICATORS AND CONTROL SIGNALS GREEN AMBER Condition LED Status (Power) LED Status (Fault) Standby - ON; Main output - OFF; AC PRESENT Blinking green Off Standby - ON; Main output - ON Solid green Off Main output overcurrent, undervoltage, overvoltage Off On FAN_FAULT; overtemperature; standby overcurrent, undervoltage Off On No AC Power Off Off Power Supply Warning Event Off Blinking STATUS AND CONTROL SIGNALS I/O Signal Name Description Interface Details 4 Pulled up internally via 10K to VDD ACOK A logic high >2.0Vdc The signal output is driven high when input source is available and within acceptable Output (AC Source) A logic low <0.8Vdc limits. The output is driven low to indicate loss of input power. Driven low by internal CMOS buffer (open drain output). 4 Pulled up internally via 10K to VDD The signal is asserted, driven high, by the power supply to indicate that all outputs PWOK (Output A logic high >2.0Vdc are valid. If any of the outputs fail then this output will be hi-Z or driven low. The Output OK) A logic low <0.8Vdc output is driven low to indicate that the Main output is outside of lower limit of Driven low by internal CMOS buffer (open drain output). regulation (11.4Vdc). The signal output is driven low to indicate that the power supply has detected a 4 Pulled up internally via 10K to VDD SMB_ALERT warning or fault and is intended to alert the system. This output must be driven A logic high >2.0Vdc (FAULT/ Output high when the power is operating correctly (within specified limits). A logic low <0.8Vdc WARNING) The signal will revert to a high level when the warning/fault stimulus (that caused Driven low by internal CMOS buffer (open drain output). the alert) is removed. PRESENT_L Passive connection to +VSB_Return. The signal is used to detect the presence (installed) of a PSU by the host system. (Power Supply A logic low <0.8Vdc Output The signal is connected to PSU logic SGND within the power module. Absent) This signal is pulled up internally to the internal housekeeping supply (within the power supply). The power supply main 12Vdc output will be enabled when this PS_ON signal is pulled low to +VSB_Return. 4 (Power Supply Input Pulled up internally via 10K to VDD In the low state the signal input shall not source more than 1mA of current. The Enable/Disable 12Vdc output will be disabled when the input is driven higher than 2.4V, or open circuited. Cycling this signal shall clear latched fault conditions. This signal is used during hot swap to disable the main output during hot swap extraction. The input is pulled up internally to the internal housekeeping supply PSKILL Input A logic high >2.0Vdc (within the power supply). The signal is provided on a short (lagging pin) and should be connected to +VSB_ Return. An analog input that is used to set the address of the internal slave devices (EEPROM APS (Address 4 and microprocessor) used for digital communications. DC voltage between the limits of 0 and VDD Select) Connection of a suitable resistor, to +VSB_Return, in conjunction with an Input internal resistor divider chain, will configure the required address. TM A serial clock line compatible with PMBus Power Systems Management Protocol VIL is 0.8V maximum Part 1 – General Requirements Rev 1.1. SCL (Serial Both VOL is 0.4V maximum when sinking 3mA No additional internal capacitance is added that would affect the speed of the bus. Clock) VIH is 2.1V minimum The signal is provided with a series isolator device to disconnect the internal power supply bus in the event that the power module is unpowered. TM A serial data line compatible with PMBus Power Systems Management Protocol VIL is 0.8V maximum SDA (Serial Part 1 – General Requirements Rev 1.1. Both VOL is 0.4V maximum when sinking 3mA Data) The signal is provided with a series isolator device to disconnect the internal power VIH is 2.1V minimum supply bus in the event that the power module is unpowered. 4 VDD is an internal voltage rail derived from VSB and an internal housekeeping rail (“diode ORed” together) and is compatible with the voltage tolerances of VSB). . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 3 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter STATUS AND CONTROL SIGNALS CONTINUED Remote sense connections intended to be connected at and sense the voltage at the point of load. The voltage sense will interact with the internal module regulation loop to compensate for voltage drops due to connection resistance between the output V1_SENSE connector and the load. Compensation for up to 0.12Vdc total connection drop Input V1SENSE_RTN (output and return connections). If remote sense compensation is not required then the voltage can be configured for local sense by: V1_SENSE directly connected to power blades 6 to 10 (inclusive) V1_SENSE_RTN directly connected to power blades 1 to 5 (inclusive) The current sharing signal is connected between sharing units (forming an ISHARE bus). It is an input and/or an output (bi-directional analog bus) as the voltage on the line controls the current share between sharing units. A power supply will respond Bi-Directional to a change in this voltage but a power supply can also change the voltage Analogue voltage: ISHARE Analogue depending on the load drawn from it. On a single unit the voltage on the pin (and the +8V maximum; 4K to +12V_RTN Bus common ISHARE bus would read approximately 8VDC at 100% load (module capability). For two identical units sharing the same 100% load this would read approximately 4VDC for perfect current sharing (i.e. 50% module load capability per unit). TIMING SPECIFICATIONS Turn-On Delay & Output Rise Time: Power On Delay; Rise Time and Signaling V1 PS_ON Delay AC Input AC Input VSB VSB VSB Rise Time VSB Power On Delay V1 Rise V1; 12V Time V1; 12V V1 Power On Delay V1 PS_ON Delay PS_ON PS_ON AC_OK Delay AC_OK AC_OK PW_OK Delay PW_OK PW_OK 1. The turn-on delay after application of AC input within the operating range shall as defined in the following tables. 2. The output rise times shall be measured from 10% of the nominal output to the lower limit of the regulation band as defined in the following tables. Time Min Max Vsb Power-on-delay 2700ms Vsb Rise time 40ms 100mS V1 Rise time 2ms 10ms V1 Power-on-delay 3000ms V1 PS_ON delay 2ms 20ms V1 PWOK delay 100ms 300ms ACOK detect 500ms 2500ms . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 4 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter TIMING SPECIFICATIONS Turn-Off (Shutdown by PS_ON) Turn Off Fall Time and Signaling AC Input Turn-Off Timing Min Max Notes V1 Fall time - - Must be monotonic V1 PS_OFF delay 0ms 5ms VSB PW_OK delay off 1.0ms V1; 12V V1 PS_OFF V1 Falltime Delay PS_ON AC_OK PWOK delayoff PW_OK 1. Note this characteristic is applicable for the main 12Vdc output shutdown from PS_ON pulled high. TIMING SPECIFICATIONS Power Removal Holdup Power Removal Timing Min Max Notes Vsb holdup 40ms - V1 holdup (Effective Total) 12ms - 100% load AC fail detect - 40ms PWOK delay off 1.0ms 100% load PWOK Hold Up 11.0ms 100% load EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics IEC/EN 61000-3-2 Complies Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Complies Conducted Emissions FCC 47 CFR Part 15/CISPR 22/EN55022 Class A with 6dB margin ESD Immunity IEC/EN 61000-4-2 Level 4 criteria A Radiated Field Immunity IEC/EN 61000-4-3 Level 3 criteria B Electrical Fast Transients/Burst IEC/EN 61000-4-4 Level 3 criteria B I it Surge Immunity IEC/EN 61000-4-5 Level 3 criteria A RF Conducted Immunity IEC/EN 61000-4-6 Level 3 criteria A Magnetic Field Immunity IEC/EN 61000-4-8 3 A/m criteria B 230Vin, 100% load, Phase 0°, Dip 100% Duration 10ms (A) Voltage Dips, Interruptions IEC/EN 61000-4-11 230Vin, 50% load, Phase 0°, Dip 100% Duration 20ms (VSB:A, V1:B) 230Vin, 100% load, Phase 0°, Dip 100% Duration > 20ms (VSB, V1:B) . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 5 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter DERATING CURVES Output Current Derating vs Ambient Temperature (back to front airflow) D1U54P-W-1200-12-Hx4PC 110 100 90 80 70 90 Vac 60 50 115 Vac 40 120 Vac 30 180 Vac 20 10 0 25 30 35 40 45 50 55 60 Ambient Temperature (˚ C) Output Current Derating vs Ambient Temperature (back to front airflow) D1U54P-W-1200 -12- HA4PTC (with C16 AC Input Connector) 105 100 95 90 85 90 Vac 80 115 Vac 75 120 Vac 70 180 Vac 65 60 25 30 35 40 45 50 55 60 Ambient Temperature (˚ C) Output Current Derating vs Ambient Temperature (front to back airflow) All Models 105 100 95 90 85 90 Vac 80 115 Vac 75 120 Vac 70 180 Vac 65 60 25 30 35 40 45 50 55 60 Ambient Temperature (˚ C) . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 6 of 9 Main Output current (Adc) Main Output current (Adc) Main Output current (Adc) D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter OUTPUT CONNECTOR AND SIGNAL SPECIFICATION E1 E2 E3 E4 E5 D1 D2 D3 D4 D5 C1 C2 C3 C4 C5 1 2 3 4 5 6 7 8 9 10 B1 B2 B3 B4 B5 A1 A2 A3 A4 A5 PIN ASSIGNMENTS - D1U54P-W-1200-12-HxxPC Tyco PN 1926734-2 (Power Supply) Pin Signal Name Comments 6, 7, 8, 9, 10 V1 + 12V main output 1, 2, 3, 4, 5 PGND + 12V main output return A1 VSB Standby output B1 VSB Standby output C1 VSB Standby output D1 VSB Standby output E1 VSB Standby output A2 VSB_return Standby return B2 VSB_return Standby return C2 unused D2 unused E2 unused I2C address and protocol selection, A3 APS (select by a pull down resistor) B3 unused C3 SDA I2C data signal line D3 V1_SENSE_R - Remote Sense return E3 V1_SENSE + Remote Sense A4 SCL I2C clock signal line B4 PS_ON Remote On/Off C4 SMB_ALERT I2C alert signal D4 unused E4 ACOK AC input OK A5 PSKILL Power supply kill, short pin B5 ISHARE Current share bus, short pin C5 PWOK Power OK, short pin D5 unused E5 PRESENT_L Power supply present, short pin MATING CONNECTOR Part Number Description Tyco Electronics 2-1926739-5 Right Angle . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 7 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter WIRING DIAGRAM FOR OUTPUT Dotted lines show optional remote sense connections. Optional remote sense lines can be attached to a load that is a distance away from the power supply to improve regulation at the load. V1_SENSE (Main Output Remote Sense) V1_SENSE (Main Output Remote Sense) +12V main output +12V main output E3 6-10 E3 6-10 D1U54P 12V load D1U54P 1-5 +12V main output return 1-5 +12V main output return V1_SENSE_R V1_SENSE_R D3 D3 ISHARE ISHARE B5 (or D4) B5 (or D4) VSB A1,B1,C1,D1,E1 VSB A1,B1,C1,D1,E1 PS_ON B4 B4 PS_ON VSB load FET, BJT, wire or switch (debounced ) to turn on +12V main output A2,B2 VSB_return VSB_return A2,B2 PS_KILLA5 (or A3) A5 (or A3) PS_KILL CURRENT SHARING NOTES 1. Main Output current sharing is achieved using the active current share method. (See wiring diagram for connection details.) Current sharing can be achieved with or without remote sense connected to the common load. 2. +VSB outputs can be tied together for redundancy but total combined output power must not exceed the rated standby power. The +VSB output has internal ORing MOSFET for additional redundancy / internal short protection. 3. The current share pin B5 (or D4 for alternate pin out model) is a connection between the units. It is input and/or output as the voltage on the line controls the current share. A power supply will respond to a change in this voltage but a power supply can also change the voltage depending on the load drawn from it. On a single unit this would read approximately 8V at 100% load. For two units sharing load then this should read approximately 4V for perfect current sharing. 4. Up to 8 units can be paralleled together. Please consult your Murata sales representative if operation with more than 8 units in parallel is needed. 5. The load for both the main 12V and the VSB rails at initial startup shall not be allowed to exceed the capability of a single unit. The load can be increased after a delay of 3sec (minimum), to allow all sharing units to achieve steady state regulation. . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 8 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter MECHANICAL DIMENSIONS AC input connector: IEC 320-C14 Alternate input connector: IEC 320-C16 (for HAxPTC models); Link back to front page Dimensions: 2.15" x 12.657" x 1.575" [54.5mm x 322.0mm x 40.0mm] MECHANICAL DIMENSIONS OPTIONAL ACCESSORIES Description Part Number 12V D1U54P Output Connector Card D1U54P-12-CONC APPLICATION NOTES Document Number Description Link ACAN-44 D1U54P Output Connector Card www.murata-ps.com/data/apnotes/acan-44.pdf ACAN-45 D1U54P-x Communication Protocol www.murata-ps.com/data/apnotes/acan-45.pdf This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2016 Murata Power Solutions, Inc. . www.murata-ps.com/support www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B02 Page 9 of 9