D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter PRODUCT OVERVIEW The D1U54P-W-1500-12-HxxTC product series offers very high efficiency in a compact form factor. These variants offers 1500 watt, and is a power factor corrected front end supply with a 12Vdc main output and either a 3.3V, 5V or 12V auxiliary/standby output. Active (digital) current sharing is provided and up to eight supplies may be operated in parallel. The supply may be hot plugged, and auto recovers from overtemperature faults, that are reported by a status LEDS on the front panel in addition to logic and PMBus™ status signals. The low profile 1U package and excellent 35W/cubic inch power density it ideal for delivering reliable, efficient power to servers, workstations, storage systems and other 12V distributed power architectures. INPUT CHARACTERISTICS Power Output Power Output Power Output Input Voltage Input Voltage Input Voltage Main Standby Part Number MPS # Airflow (200-240 Vac) (110-120 Vac) (100 Vac) Output Output 45°C 45°C 40°C D1U54P-W-1500-12-HC4TC M1891 3.3Vdc Back to D1U54P-W-1500-12-HA4TC M1893 5Vdc Front D1U54P-W-1500-12-HB4TC M1895 1500W 1400W 1260W 12Vdc 12Vdc D1U54P-W-1500-12-HC3TC M1892 3.3Vdc Front to D1U54P-W-1500-12-HA3TC M1894 5Vdc Back FEATURES 1 The HAxTC variants are certified for compliance to 80 PLUS® Platinum efficiency requirements.  +1500W continuous output power  IEC60320-C16 connector for maximized INPUT CHARACTERISTICS low line operation Parameter Conditions Min. Nom. Max. Units  94% efficiency at 50% Load Input Voltage Operating Range 90 115/230 264 Vac  12V main output Input Frequency 47 50/60 63 Hz  3.3V; 5V and 12V standby output Options Turn-on Input Voltage Ramp up 74 84 Vac  1U height: 2.15" x 12.65" x 1.57" Turn-off Input Voltage Ramp down 70 80  > 35 watts per cubic inch density Maximum current at Vin = 90Vac/60Hz; 1260W 15 Arms  N+1 redundancy, hotpluggble, Ishare Cold start between 0 to Inrush Current 50 Apk compatable with DC input series 200msec, 264Vac  active (digital) current sharing on 12V Power Factor At 230Vac, full load 0.99 main output; integral ORing /isolation 20% load 90 device MOSFET Efficiency (230Vac) excluding fan load 50% load 94 %  internal cooling fan (variable speed) 100% load 91 overvoltage, overcurrent, OUTPUT VOLTAGE CHARACTERISTICS overtemperature protection Output Parameter Conditions Min. Typ. Max. Units  PMBus™/I²C interface with LED status Nominal Output Voltage 12 Vdc indicators Output Set Point Accuracy 50% load; Tamb =25°C -0.5 +0.5  RoHS compliant 2 % Line and Load Regulation Measrured at remote sense -1.0 +1.5  two year warranty 1,2 Ripple Voltage & Noise 20MHz Bandwidth 120 mV p-p 12V Output Current 1500W; (115-264Vac) 0 125 A Output Current 1260W; (90-264Vac) 0 105 Load Capacitance 30,000 μF Nominal Output Voltage 3.3 Vdc Line and Load Regulation 3.14 3.46 1,3 3.3VSB Ripple Voltage & Noise 20MHz Bandwidth 75 mV p-p Output Current 0 4 A Load Capacitance 0 3000 μF Nominal Output Voltage 5.0 Available now at: www.murata-ps.com/en/3d/acdc.html Vdc Line and Load Regulation 4.76 5.24 1,3 5VSB Ripple Voltage & Noise 20MHz Bandwidth 75 mV p-p Output Current 0 4 A Load Capacitance 0 3000 μF Nominal Output Voltage 12 Vdc Line and Load Regulation 11.7 12.3 1,3 12VSB Ripple Voltage & Noise 120 mV p-p A Output Current 0 2.5 Load Capacitance μF 1000 1 Ripple and noise are measured with 0.1 μF of ceramic capacitance and 10 μF of tantalum capacitance on each of the power supply outputs. A short coaxial cable to the scope termination is used. 2 Minimum Load of 5A. 3 Minimum Load of 0.25A. http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 1 of 10 D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Startup Time AC ramp up 3 s 12V Main 10% to 60% load step; 1A/μs slew rate -5 +5 % nom Recovery Time to within 1% Vnom 2 Ms 3.3V & 5VSB, 10% to 60% load step; 1A/μs slew rate -5 +5 % nom Transient Response Recovery Time to within 1% Vnom 2 ms 12VSB, 10% to 60% load step; 1A/μs slew rate. -5 +5 % nom Recovery Time to within 1% Vnom 2 ms Current sharing accuracy At 100% load -5 +5 % Hot Swap Transients All outputs remain in regulation -5 +5 % Holdup Time 110/230Vac in voltage ranges, 100% load (1500W) 12 ms ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range -40 70 Operating Temperature Range 1500W (180-264Vac) See Derating Curves -5 45 °C Operating Temperature Range 1260W (90-264Vac) -5 Continuous 45 Operating Temperature Range (85-264Vac) See Derating Curves -5 40 Operating Humidity Noncondensing 5 90 % Storage Humidity 5 95 Altitude (without derating at 40°C) 3000 m Shock 30G non-operating Sine sweep; 5-150Hz, 2G; Operational Vibration random vibration, 5-500Hz, 1.11G MTBF Per Telcordia SR-332 M1C1 @40°C 540K hrs. CAN/CSA C22.2 No 60950-1-07, Am.1:2011; Am 2_2014 nd nd UL 60950-1-2011, 2 Ed. UL 60950-1, 2 Ed. TUV EN60950 nd Safety Approval Standards (Planned Submissions) IEC60950-1:2005 (2 Ed.)_A1 EN 60950-1:2006+A11+A1+A12+A2 BSMI (099/09/30); CNS13438 ((095/06/01) CQC GB4943.1-2011; GB9254-1-2008; GB17625, 1-2012 Input Fuse Power Supply has single internal 20A/250V fast blow fuse on the AC line input Weight 3.15 lbs. (1.43 kg) PROTECTION CHARACTERISTICS Output Parameter Conditions Min. Typ. Max. Units Voltage Overtemperature (intake) Autorestart 60 65 70 °C Overvoltage Latching 13.0 14.5 V Shortciruit 4 Hiccup then latch 145 - 12V A Overcurrent At 90-264VVac 4 Hiccup, >500msec each, then latch 132 150 Overvoltage Latching 3.6 4.0 V 3.3VSB Overcurrent Hiccup 5.1 6.7 A Overvoltage Latching 5.4 6.0 V 5VSB Overcurrent Hiccup 5.1 6.7 A Overvoltage Latching 13.0 14.5 V 12VSB Overcurrent Hiccup 3.5 4.5 A http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 2 of 10 D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Input to Output - Reinforced 3000 Vrms Insulation Safety Rating / Test Voltage Input to Chassis - Basic 1500 Vrms Isolation Output to Chassis 500 Vdc EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics IEC/EN 61000-3-2 Complies with Class A limits Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Complies Conducted Emissions FCC 47 CFR Part15/CISPR22/EN55022 Class A with 6dB margin ESD Immunity IEC/EN 61000-4-2 ±8KV Contact; ±15KV air discharge; Criteria B Radiated Field Immunity IEC/EN 61000-4-3 3V/m, 1KHz, 80% AM, 80MHz to 1GHz Criteria A Electrical Fast Transients/Burst Immunity IEC/EN 61000-4-4 Level 3 criteria B Surge Immunity IEC/EN 61000-4-5 Level 3 criteria B, measured at the power supply input connector RF Conducted Immunity IEC/EN 61000-4-6 Level 2 criteria A Magnetic Field Immunity IEC/EN 61000-4-8 3 A/m criteria B 230Vin, 100% load, Phase 0°, Dip 100% Duration 10ms (A) Voltage Dips, Interruptions IEC/EN 61000-4-11 230Vin, 50% load, Phase 0°, Dip 100% Duration 20ms (VSB:A, V1:B) 230Vin, 100% load, Phase 0°, Dip 100% Duration > 20ms (VSB, V1:B) STATUS INDICATORS AND CONTROL SIGNALS (BI_COLOUR LED) GREEN AMBER Condition LED Status (Power) LED Status (Fault) Standby - ON; Main output - OFF; AC PRESENT Blinking green Off Standby - ON; Main output - ON Solid green Off Main output overcurrent, undervoltage, overvoltage Off On FAN_FAULT; overtemperature; standby overcurrent, undervoltage Off On No AC Power Off Off Power Supply Warning Event Off Blinking ADDR ADDRESS SELECTION ADDR pin (A3) resistor to GND Power Supply Main Controller Power Supply External EEPROM (K-ohm)* (Serial Communications Slave Address) (Serial Communications Slave Address) 0.82 0xB0 0xA0 2.7 0xB2 0xA2 5.6 0xB4 0xA4 8.2 0xB6 0xA6 15 0xB8 0xA8 27 0xBA 0xAA 56 0xBC 0xAC 180 0xBE 0xAE * The resistor shall be +/-5% tolerance http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 3 of 10 D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter STATUS AND CONTROL SIGNALS Signal Name I/O Description Interface Details 1 The signal output is driven high when input source is available and within acceptable limits. The output Pulled up internally via 10K to VDD . is driven low to indicate loss of input power. A logic high >2.0Vdc INPUT_OK (AC Source) Output There is a minimum of 1ms pre-warning time before the signal is driven low prior to the PWR_OK signal A logic low <0.8Vdc going low. The power supply must ensure that this interface signal provides accurate status when AC Driven low by internal CMOS buffer power is lost. (open drain output). 1 Pulled up internally via 10K to VDD . The signal is asserted, driven high, by the power supply to indicate that all outputs are valid. If any of the A logic high >2.0Vdc PW_OK (Output OK) Output outputs fail then this output will be hi-Z or driven low. The output is driven low to indicate that the Main A logic low <0.8Vdc output is outside of lower limit of regulation (11.4Vdc). Driven low by internal CMOS buffer (open drain output). 1 Pulled up internally via 10K to VDD . The signal output is driven low to indicate that the power supply has detected a warning or fault and is A logic high >2.0Vdc SMB_ALERT intended to alert the system. This output must be driven high when the power is operating correctly Output A logic low <0.8Vdc (FAULT/WARNING) (within specified limits). Driven low by internal CMOS buffer The signal will revert to a high level when the warning/fault stimulus (that caused the alert) is removed. (open drain output). Passive connection to +VSB_Return. PRESENT_L The signal is used to detect the presence (installed) of a PSU by the host system. The signal is Output A logic low <0.8Vdc (Power Supply Absent) connected to PSU logic SGND within the power module. This signal is pulled up internally to the internal housekeeping supply (within the power supply). The 1 Pulled up internally via 10K to VDD . PS_ON power supply main 12Vdc output will be enabled when this signal is pulled low to +VSB_Return. A logic high >2.0Vdc (Power Supply Input In the low state the signal input shall not source more than 1mA of current. The 12Vdc output will be A logic low <0.8Vdc Enable/Disable disabled when the input is driven higher than 2.4V, or open circuited. Cycling this signal shall clear Input is via CMOS Schmitt trigger buffer. latched fault conditions. 1 Pulled up internally via 10K to VDD . This signal is used during hot swap to disable the main output during hot swap extraction. The input is A logic high >2.0Vdc PS_KILL Input pulled up internally to the internal housekeeping supply (within the power supply). A logic low <0.8Vdc The signal is provided on a short (lagging pin) and should be connected to +VSB_Return. Input is via CMOS Schmitt trigger buffer. An analog input that is used to set the address of the internal slave devices (EEPROM and microprocessor) used for digital communications. DC voltage between the limits of 0 and ADDR (Address Select) Input Connection of a suitable resistor to +VSB_Return, in conjunction with an internal resistor divider chain, +3.3Vdc. will configure the required address. TM A serial clock line compatible with PMBus Power Systems Management Protocol Part 1 – General VIL is 0.8V maximum Requirements Rev 1.1. VOL is 0.4V maximum when sinking SCL (Serial Clock) Both No additional internal capacitance is added that would affect the speed of the bus. 3mA The signal is provided with a series isolator device to disconnect the internal power supply bus in the VIH is 2.1V minimum event that the power module is unpowered. TM A serial data line compatible with PMBus Power Systems Management Protocol Part 1 – General VIL is 0.8V maximum Requirements Rev 1.1. VOL is 0.4V maximum when sinking SDA (Serial Data) Both The signal is provided with a series isolator device to disconnect the internal power supply bus in the 3mA event that the power module is unpowered. VIH is 2.1V minimum Remote sense connections intended to be connected at and sense the voltage at the point of load. The voltage sense will interact with the internal module regulation loop to compensate for voltage drops Compensation for up to 0.12Vdc total V1_SENSE due to connection resistance between the output connector and the load. Input connection drop (output and return V1SENSE_RTN If remote sense compensation is not required then the voltage can be configured for local sense by: connections). 1. V1_SENSE directly connected to power blades 6 to 10 (inclusive) 2. V1_SENSE_RTN directly connected to power blades 1 to 5 (inclusive) The current sharing signal is connected between sharing units (forming an ISHARE bus). It is an input and/or an output (bi-directional analog bus) as the voltage on the line controls the current Bi- share between sharing units. A power supply will respond to a change in this voltage but a power Analogue voltage: Directional ISHARE supply can also change the voltage depending on the load drawn from it. On a single unit the voltage +8V maximum; 10K to +12V_RTN Analogue on the pin (and the common ISHARE bus would read 8VDC at 100% load (module capability). For two Bus identical units sharing the same 100% load this would read 4VDC for perfect current sharing (i.e. 50% module load capability per unit). 1. VDD is an internal voltage rail derived from VSB and an internal housekeeping rail (“diode ORed”) and is compatible with the voltage levels of TTL and CMOS logic families. http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 4 of 10 D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter TIMING SPECIFICATIONS Turn-On Delay & Output Rise Time: 1. The turn-on delay after application of AC input within the operating range shall as defined in the following tables. 2. The output rise times shall be measured from 10% of the nominal output to the lower limit of the regulation band as defined in the following tables. Time Min Max 12Vsb Rise time 100ms 200ms 3.3Vsb and 5Vsb Rise time 1 25ms V1 Rise time 20ms 120ms Vsb Power-on-delay 2700ms V1 Power-on-delay 3000ms V1 PS_ON delay 100ms 150ms V1 PWOK delay 20ms 40ms ACOK detect 400ms 500ms http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 5 of 10 D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter TIMING SPECIFICATIONS Turn-Off (Shutdown by PS_ON) Turn-Off Timing Min Max Notes V1 Fall time - - Must be monotonic V1 PS_OFF delay 0ms 5ms PW_OK delay off 0.5ms 1. Note this characteristic is applicable for the main 12Vdc output shutdown from PS_ON pulled high (de-asserted). TIMING SPECIFICATIONS Power Removal Holdup Power Removal Timing Min Typ. Max Notes Vsb holdup 40ms - V1 holdup 12ms - Full load (1500W) Input fail detect - 6mS - PWOK delay off 0.5ms 2.5ms http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 6 of 10 D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter DERATING CURVES Output Power Derating D1U54P-W-1500-12-HxxTC 1600 1400 1200 100 Vac 1000 110 Vac 800 200-240 Vac 600 120 Vac 400 200 0 25 30 35 40 45 50 55 60 Ambient Temperature 1 Input current must be limited by end user to 12A for North American certification 2 The power supply has no limitation on its output current/power in the respect of meeting the operating conditions shown by the derating limits shown above. It is the responsibility of the end user to ensure operating conditions are maintained within their safety agency certification limits to assure safe and reliable operation Airflow Characteristics D1U54-W-1500-12-HBxxx P & Q CURVE 450 400 350 300 250 Airflow Front to Back Airflow Back to Front 200 150 100 50 0 0 2 4 6 8 10 12 14 PSU airflow (CFM) http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 7 of 10 Back Pressure (Pa) Maximum Output power D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter OUTPUT CONNECTOR & SIGNAL INTERFACE Note: With respect to signals columns 5, “3” refers to the shortest level signal pin; the “shortest” pins are the “last to make, first to break” in the mating sequence. PIN ASSIGNMENTS - D1U54P-W-1500-12-HxxTC FCI PN 10122460-005LF (Power Supply) Pin Signal Name Comments 6, 7, 8, 9, 10 V1 + 12V main output 1, 2, 3, 4, 5 PGND + 12V main output return A1 VSB Standby output B1 VSB Standby output C1 VSB Standby output D1 VSB Standby output E1 VSB Standby output A2 VSB_return Standby return B2 VSB_return Standby return C2 Unused No User Connection D2 Unused No User Connection E2 Unused No User Connection A3 ADDR I2C address selection, (select by external pull B3 unused No User Connection C3 SDA I2C data signal line D3 V1_SENSE_R - Remote Sense return E3 V1_SENSE + Remote Sense A4 SCL I2C clock signal line B4 PS_ON Remote On/Off C4 SMB_ALERT I2C alert signal D4 Unused No User Connection E4 ACOK AC input OK A5 PSKILL Power supply kill, short pin B5 ISHARE Current share bus, short pin C5 PWOK Power OK, short pin D5 Unused No User Connection E5 PRESENT_L Power supply present, short pin MATING CONNECTOR Part Number Description Tyco Electronics 2-1926739-5 Right Angle FCI 10108888-R10253SLF Right Angle http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 8 of 10 D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter WIRING DIAGRAM CURRENT SHARING NOTES 1. Main Output: Current sharing is achieved using the active current share method. 2. Current sharing can be achieved with or without the remote (V_SENSE) connected to the common load. 3. +VSB Outputs can be tied together for redundancy but total combined output power must not exceed the rated standby power of a single unit. The +VSB output has an internal ORING MOSFET for additional redundancy/internal short protection. 4. The current sharing pin B5 is connected between sharing units (forming an ISHARE bus). It is an input and/or an output (bi-directional analog bus) as the voltage on the line controls the current share between sharing units. A power supply will respond to a change in this voltage but a power supply can also change the voltage depending on the load drawn from it. On a single unit the voltage on the pin (and the common ISHARE bus would read 8VDC at 100% load (power module capability). For two units sharing the same load this would read 4VDC for perfect current sharing (i.e. 50% power capability per unit). 5. The load for both the main 12V and the VSB rails at initial startup shall not be allowed to exceed the capability of a single unit. The load can be increased after a delay of 3sec (minimum), to allow all sharing units to achieve steady state regulation. MECHANICAL DIMENSIONS http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 9 of 10 D1U54P-W-1500-12-HxxTC Series 54mm 1U Front End AC-DC Power Supply Converter 1. AC input connector: IEC 60320-C16 2. Dimensions: 54.5mm x 321.5mm x 40.0mm [2.15" x 12.657" x 1.575"]; metric measurements take precedent 3. This drawing is a graphical representation of the product and may not show all fine details. 4. Reference File: D1U54P-W-1500-12-HxxC (1893, 1895series)_Drawing for Product Datasheet_20160411.dwg OPTIONAL ACCESSORIES Description Part Number 12V D1U54P Output Connector Card D1U54P-12-CONC APPLICATION NOTES Document Number Description Link ACAN-64 D1U54P Output Connector Card http://power.murata.com/datasheet?/data/apnotes/acan-64.pdf ACAN-66 D1U54P-W-1500-12-HxxTC PMBus Protocol http://power.murata.com/datasheet?/data/apnotes/acan-66.pdf This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Murata Power Solutions, Inc. Refer to: http://www.murata-ps.com/requirements/ 11 Cabot Boulevard, Mansfield, MA 02048 -1151 U.S.A. Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not ISO 9001 and 14001 REGISTERED imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. ©2016 Murata Power Solutions, Inc.. http://www.murata-p.com/support d1U54p-w-1500-12-hxxtc.a04 page 10 of 10