D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter PRODUCT OVERVIEW The D1U54P-W-650-12-HBxC series are very high efficiency 650 watt power factor corrected front end supplies with a 12V main output and a 12V Standby. An active (analogue) current share characteristic is provided to allow units to operate in parallel. The power supply may be hot plugged; recovers from overtemperature faults, and has status LEDs on the front panel in addition to hardware signal logic and PMBus™ status signals. The low profile 1U package and 21.4W/cubic inch power density make them ideal for delivering reliable, efficient power to networking equipment, workstations, storage systems and other 12V distributed power architectures. ORDERING GUIDE Murata Internal Power Output Main Standby Part Number Airflow Part Number 90 to 264Vac Output Output D1U54P-W-650-12-HB3C M1877 Front to Back 650W 12Vdc 12Vdc D1U54P-W-650-12-HB4C M1876 Back to front FEATURES INPUT CHARACTERISTICS  650W output power Parameter Conditions Min. Nom. Max. Units  94% efficiency at 50% load Input Source Voltage Operating Range 90 115/230 264 Vac  12V main output Input Source Frequency 47 50/60 63 Hz  12V standby output Turn-on Input Voltage Ramp up 74 84 Vac  1U height: Turn-off Input Voltage Ramp down 70 80  2.15" x 9.0" x 1.57" Maximum current at Vin = 100Vac 650W 10 Arms  54.5mm x 228.6mm x 40mm Inrush Current Cold start between 0 to 200msec 25 Apk  Full digital control At 230Vac, 100% load 0.96 Power Factor  21.4 Watts per cubic inch density At 230Vac, 50% load 0.95  N+1 redundancy capable, including hot plugging At 230Vac, 20% load 90  Active (analogue) current sharing on 12V main Efficiency (excluding fan load) At 230Vac, 50% load 94 % output; ORING FET At 230Vac, 100% load 91  Overvoltage, Overcurrent, Overtemperature OUTPUT VOLTAGE CHARACTERISTICS protection Nominal  Internal cooling fan (variable speed) Parameter Conditions Min. Typ. Max. Units Output  PMBus™/I2C interface with status indicators Voltage  RoHS compliant Output Set Point Accuracy 50% load; Tamb =25°C 11.96 12.00 12.04 Vdc  Two Year Warranty Setpoint; temperature; line % Line and Load Regulation -1.0% +1.0 and load 1, 2 12V Ripple Voltage & Noise 20MHz Bandwidth 120 mV p-p Output Current Range 0 54.2 A Load Capacitance 500 4000 μF Output Set Point Accuracy 50% load; Tamb = 25°C 11.96 12.00 12.04 Setpoint; temperature; line Vdc Line and Load Regulation 11.7 12.3 12VSB and load 1 Ripple Voltage & Noise 20MHz Bandwidth 120 mV p-p Output Current 0 2 A www.murata-ps.com/en/3d/acdc.html 1 Ripple and noise are measured with 0.1 μF of ceramic capacitance and 10 μF of tantalum capacitance on each of www.murata-ps.com/en/3d/acdc.html the power supply outputs. A short coaxial cable to the measurement ‘scope input, is used. www.murata-ps.com/en/3d/acdc.html 2 Measurements assume the use of the minimum load capacitance as specified for the main 12V output and a www.murata-ps.com/en/3d/acdc.html minimum load of 5%. www.murata-ps.com/en/3d/acdc.html Below 5% loading the overall voltage deviation shall be within ±500mV due to zero load “skip” cycle mode of www.murata-ps.com/en/3d/acdc.html operation. Available now at: www.murata-ps.com/en/3d/acdc.html Test Certificate For full details go to and Test Report www.murata-ps.com/rohs www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 1 of 9 D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter OUTPUT CHARACTERISTICS Max. Parameter Conditions Min. Typ. Units Startup Time AC ramp up Note: Following a “turn off” of the 12V Main output (for any reason whatsoever) the 3 s output shall not be allowed to “turn on” again for 1sec (even if all necessary operating conditions are met). Main 12V, 50% load step, 1A/μs di/dt ±5 % Transient Response 500 µs 12VSB, 50% load step, 1A/μs di/dt Current sharing accuracy (Main 12V output) >10% load; (* percentage of full load) ±5* % ±5 % Hot Swap Transients Holdup Time (Total Effective Hold Up - See Timing Waveforms) Full AC Input Source Range; full load 12 ms ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range -40 70 °C Operating Temperature Range 90V-264Vac, 650W -5 50 Operating Humidity Noncondensing; +45°C 5 90 % Storage Humidity 5 95 Altitude (without derating at 40°C) 3000 m Shock 30G non-operating Sine sweep; 5-200Hz, 2G; Operational Vibration random vibration, 5-500Hz, 1.11G MTBF(Target) Per Telcordia SR-332 M1C1 @40°C 576K hrs CAN/CSA C22.2 No 60950-1-07, Am.1:2011, Am 2:2014 ANSI/UL 60950-1-2014 IEC60950-1:2005 (2nd Ed.), Am 1:2009 + Am 2:2013 Safety Approvals EN 60950-1:2006+A11:2009 +A1:2010 +A12:2011 +A2:2013 BSMI CNS14336-1 (099/09/30); CNS13438 ((095/06/01) CCC GB4943.1-2011; GB9254-1-2008; GB17625, 1-2012 Input Fuse Power Supply has internal 12.5A/250V fast blow fuse on the AC line input Weight 1.63 lbs (0.741 kg) AIRFLOW; PRESSURE VS. FLOW (PQ) CURVES D1U54P-W-650-12-HB3C & D1U54P-W-650-12-HB4C D1U54-W-650-12-HBxC P & Q CURVE Orignal curve in Excel spreadsheet at following location: M1845_airflow_meas_01-12-2015.xlsx 250 200 150 Airflow Front to Back 100 Airflow Back to Front 50 0 0 2 4 6 8 10 PSU airflow (CFM) Notes: 1. The above curves represent performance based upon the use of a 20mm thickness fan. 2. Curves recorded at room ambient (circa 25°C). 3. Curves generated with intermal fan running at 100% duty cycle www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 2 of 9 Back Pressure (Pa) D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter PROTECTION CHARACTERISTICS Output Parameter Conditions Min. Typ. Max. Units Overtemperature (intake) Autorestart with 4°C hysteresis for recovery (warning issued at 70°C) 75 °C Overvoltage Latching 13.0 14.5 V The output shall shutdown when an overcurrent condition is detected. It will auto restart after 1sec; however if the overcurrent condition is redetected the output will once again shutdown. 12V Overcurrent (target) The output will once again re-start, however if the overcurrent 60 70 A condition persists it will latch of after the fifth unsuccessful attempt. To reset the latch it will be necessary to toggle the PS_ON_L signal (B4) or recycle the incoming AC source. Overvoltage Latching 13.0 14.5 V The output shall shutdown when an overcurrent is detected. 12VSB It will auto restart after 2sec; however if the overcurrent is re-detected Overcurrent 2.5 3.5 A the output will once again shutdown. This cycle will occur indefinitely while the overcurrent condition i ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Input to Output - Reinforced Vrms 3000 Insulation Safety Rating Input to Chassis - Basic 1500 Vrms Isolation Output to Chassis Vdc 500 EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics IEC/EN 61000-3-2 Complies Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Complies Conducted Emissions FCC 47 CFR Part 15 Class A with 6dB margin CISPR 22/EN55022 ESD Immunity IEC/EN 61000-4-2 Level 4 criteria A Radiated Field Immunity IEC/EN 61000-4-3 Level 3 criteria B Electrical Fast Transients/Burst Immunity IEC/EN 61000-4-4 Level 3 criteria A # Surge Immunity IEC/EN 61000-4-5 • 6kV common mode and differential mode, unit shall fail safely . • 4kV common mode and differential mode, unit shall survive; the output may shut down and recover # automatically (Criteria B) or require manual intervention (Criteria C) . • 2kV common and differential mode, unit passes criteria A (normal performance)* RF Conducted Immunity IEC/EN 61000-4-6 Level 3 criteria A Magnetic Field Immunity IEC/EN 61000-4-8 3 A/m criteria B 230Vin, 80% load, Phase 0°, Dip 100% Duration 10ms (A) Voltage Dips, Interruptions IEC/EN 61000-4-11 230Vin, 50% load, Phase 0°, Dip 100% Duration 20ms (VSB:A, V1:B) 230Vin, 100% load, Phase 0°, Dip 100% Duration > 20ms (VSB, V1:B) * Impedance is 2 ohms for ±2KV differential and common mode to comply with NEBS GR-1089 limits. Maximum load capacitance is required for these tests. # Tests above ±2KV will be performed for information purposes to IEC/EN66100-4-5 with 12ohm impedance, differential & common mode. STATUS INDICATORS LED NAME LED MODE LED STATE/OPERATION DESCRIPTION Input OK Solid Green Input voltage operating within normal specified range Input OV/UV WARNING Blinking Green Input voltage operating in: 1) overvoltage warning, or 2) undervoltage warning range Input OFF OR FAULT Off Input voltage operating: 1) above overvoltage range, or 2) below undervoltage range, or 3) not present Output POWER GOOD Solid Green Main output and standby output enabled with no power supply warning or fault detected Output STANDBY Blinking Green Standby output enabled with no power supply warning or fault detected Output WARNING Blinking Amber Power supply warning detected as per PMBus STATUS_X reporting • bytes Output FAULT Solid Amber Power supply fault detected as per PMBus STATUS_X reporting www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 3 of 9 D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter • bytes • LED fault/warning operation follows PMBus fault/warning reporting status flags but will not be 'sticky';(i.e. if the fault stimulus is removed, even though the actual fault/warning is still showing (still “sticky” and not cleared), the relevant LED will revert to normal (non -fault) operation. STATUS AND CONTROL SIGNALS Signal Name I/O Description Interface Details INPUT_OK (AC Source) Output The signal output is driven high when input source is available and within acceptable limits. The Pulled up internally via 10K to 3.3Vdc. output is driven low to indicate loss of input power. A logic high >2.0Vdc There is a minimum of 1ms pre-warning time before the signal is driven low prior to the PWR_OK A logic low <0.8Vdc signal going low. The power supply must ensure that this interface signal provides accurate status Driven low by internal CMOS buffer when AC power is lost. (open drain output). PW_OK (Output OK) Output The signal is asserted, driven high, by the power supply to indicate that all outputs are valid. If any of Pulled up internally via 10K to 3.3Vdc. the outputs fail then this output will be hi-Z or driven low. The output is driven low to indicate that the A logic high >2.0Vdc Main output is outside of lower limit of regulation (11.4Vdc). A logic low <0.8Vdc Driven low by internal CMOS buffer (open drain output). SMB_ALERT Output The signal output is driven low to indicate that the power supply has detected a warning or fault and is Pulled up internally via 10K to 3.3Vdc. intended to alert the system. This output must be driven high when the power is operating correctly (FAULT/WARNING) A logic high >2.0Vdc (within specified limits). A logic low <0.8Vdc The signal will revert to a high level when the warning/fault stimulus (that caused the alert) is Driven low by internal CMOS buffer removed. (open drain output). PRESENT_L Output The signal is used to detect the presence (installed) of a PSU by the host system. The signal is Passive connection to +VSB_Return. connected to PSU logic SGND within the power module. (Power Supply Absent) A logic low <0.8Vdc PS_ON Input This signal is pulled up internally to the internal housekeeping supply (within the power supply). The Pulled up internally via 10K to 3.3Vdc. power supply main 12Vdc output will be enabled when this signal is pulled low to +VSB_Return. (Power Supply A logic high >2.0Vdc Enable/Disable In the low state the signal input shall not source more than 1mA of current. The 12Vdc output will be A logic low <0.8Vdc disabled when the input is driven higher than 2.4V, or open circuited. Cycling this signal shall clear Input is via CMOS Schmitt trigger latched fault conditions. buffer. PS_KILL Input This signal is used during hot swap to disable the main output during hot swap extraction. The input is Pulled up internally via 10K to 3.3Vdc. pulled up internally to the internal housekeeping supply (within the power supply). A logic high >2.0Vdc The signal is provided on a short (lagging pin) and should be connected to +VSB_Return. A logic low <0.8Vdc Input is via CMOS Schmitt trigger b ff ADDR (Address Select) Input An analogue input that is used to set the address of the internal slave devices (EEPROM and DC voltage between the limits of 0 and microprocessor) used for digital communications. +3.3Vdc. Connection of a suitable resistor to +VSB_Return, in conjunction with an internal resistor divider chain, will configure the required address. TM SCL (Serial Clock) Both A serial clock line compatible with PMBus Power Systems Management Protocol Part 1 – General VIL is 0.8V maximum Requirements Rev 1.1. VOL is 0.4V maximum when sinking No additional internal capacitance is added that would affect the speed of the bus. 3mA The signal is provided with a series isolator device to disconnect the internal power supply bus in the VIH is 2.1V minimum event that the power module is unpowered, TM SDA (Serial Data) Both A serial data line compatible with PMBus Power Systems Management Protocol Part 1 – General VIL is 0.8V maximum Requirements Rev 1.1. VOL is 0.4V maximum when sinking The signal is provided with a series isolator device to disconnect the internal power supply bus in the 3mA event that the power module is unpowered, VIH is 2.1V minimum V1_SENSE Input Remote sense connections intended to be connected at and sense the voltage at the point of load. Compensation for a up to 0.12Vdc V1SENSE_RTN The voltage sense will interact with the internal module regulation loop to compensate for voltage total connection drop (output and drops due to connection resistance between the output connector and the load. return connections). If remote sense compensation is not required then the voltage can be configured for local sense by: 1. V1_SENSE directly connected to power blades 6 to 10 (inclusive) 2. V1_SENSE_RTN directly connected to power blades 1 to 5 (inclusive) ISHARE Bi- The current sharing signal is connected between sharing units (forming an ISHARE bus). It is an Analogue voltage: Directional input and/or an output (bi-directional analogue bus) as the voltage on the line controls the current +8V maximum; 10K to +12V_RTN Analogue share between sharing units. A power supply will respond to a change in this voltage but a power Bus supply can also change the voltage depending on the load drawn from it. On a single unit the voltage on the pin (and the common ISHARE bus would read 8VDC at 100% load (module capability). For two identical units sharing the same 100% load this would read 4VDC for perfect current sharing (i.e. 50% module load capability per unit). www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 4 of 9 D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter TIMING SPECIFICATIONS Turn-On Delay & Output Rise Time: Power On Delay; Rise Time and Signaling V1 PS_ON Delay AC Input AC Input VSB VSB VSB Rise Time VSB Power On Delay V1 Rise V1; 12V Time V1; 12V V1 PS_ON Delay V1 Power On Delay PS_ON PS_ON AC_OK Delay AC_OK AC_OK PW_OK Delay PW_OK PW_OK 1. The turn-on delay after application of AC input within the operating range shall as defined in the following tables. 2. The output rise times shall be measured from 10% of the nominal output to the lower limit of the regulation band as defined in the following tables. Time Min Max Vsb Rise time 100ms 200ms V1 Rise time 20ms 120ms Vsb Power-on-delay 2700ms V1 Power-on-delay 3000ms V1 PS_ON delay 100ms 150ms V1 PWOK delay 100ms 300ms ACOK detect 300ms 2000ms TIMING SPECIFICATIONS Turn-Off (Shutdown by PS_ON) Turn Off Fall Time and Signaling AC Input Turn-Off Timing Min Max Notes V1 Fall time - - Must be monotonic V1 PS_OFF delay 0ms 5ms VSB PW_OK delay off 1.0ms V1; 12V V1 Falltime V1 PS_OFF Delay PS_ON AC_OK PWOK delayoff PW_OK 1. Note this characteristic is applicable for the main 12Vdc output shutdown from PS_ON pulled high. www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 5 of 9 D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter TIMING SPECIFICATIONS Power Removal Holdup Power removed holdup, falltime and AC Input signaling Power Removal Timing Min Max Notes Vsb holdup 40ms - V1 holdup (Effective Total) 12ms - Full load VSB AC fail detect - 40ms Vsb holdup PWOK delay off 1.0ms Full load PWOK Hold Up 11.0ms Full load V1; 12V Vsb Falltime V1 holdup V1 Falltime PS_ON AC fail detect AC_OK PWOK delayoff PW_OK PWOK Hold Up OUTPUT CONNECTOR & SIGNAL INTERFACE; FCI PN 10122460-005LF NB: With respect to signals “3” in Columns 5, refers to the shortest level signal pin; the “shortest” pins are the “last to make, first to break” in the mating sequence. www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 6 of 9 D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter OUTPUT CONNECTOR PIN ASSIGNMENTS - D1U54P-W-650-12-HBxC (Power Supply)FCI PN 10122460-005LF Pin Signal Name Comments 6, 7, 8, 9, 10 V1 (+12VOUT) +12V Main Output 1, 2, 3, 4, 5 +12V RTN/PGND +12V Main Output Return A1 +VSB Standby Output B1 +VSB Standby Output C1 +VSB Standby Output D1 +VSB Standby Output E1 +VSB Standby Output A2 +VSB_Return Standby Output Return B2 +VSB_Return Standby Output Return C2 Unused No End User Connection D2 Unused No End User Connection E2 Unused No End User Connection 2 A3 ADDR I C Address Protocol Selection; (Select address by appropriate pull down resistor – See table below) B3 Unused No End User Connection 2 C3 SDA I C Serial Data Line D3 V1_SENSE_R -VE Remote Sense Return E3 V1_SENSE +VE Remote Sense 2 A4 SCL I C Serial Clock Line B4 PS_ON_L Remote On/Off (Enable/Disable) C4 SMB_ALERT Alert signal to host system D4 Unused No End User Connection E4 AC_OK AC Input Source Present & “OK” A5 PS_KILL Power Supply “kill”; short pin B5 ISHARE Active Current Share Bus C5 PW_OK Power “OK”; short pin D5 Unused No End User Connection E5 PRESENT_L Power Module Present; short pin WIRIN MATING CONNECTOR Part Number Description TE Connectivity 2-1926739-5 Right Angle FCI 10108888-R10253SLF Right Angle ADDR ADDRESS SELECTION ADDR pin (A3) resistor Power Supply Main Controller Power Supply External EEPROM to GND (K-ohm)* (Serial Communications Slave Address) (Serial Communications Slave Address) 0.82 0xB0 0xA0 2.7 0xB2 0xA2 5.6 0xB4 0xA4 8.2 0xB6 0xA6 15 0xB8 0xA8 27 0xBA 0xAA 56 0xBC 0xAC 180 0xBE 0xAE * The resistor shall be +/-5% tolerance G DIAGRAM FOR OUTPUT www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 7 of 9 D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter WIRING DIAGRAM FOR OUTPUT Dotted lines show optional remote sense connections. Optional remote sense lines can be attached to a load that is a distance away from the power supply to improve regulation at the load. V1_SENSE V1_SENSE (Main Output Remote Sense) (Main Output Remote Sense) E3 E3 D1U54P D1U54P +12V Main Output +12V Main Output 6 -10 6-10 +12V Load 1 - 5 1 - 5 +12V Main Output Return +12V Main Output Return V1_SENSE_R V1_SENSE_R D3 D3 ISHARE ISHARE B5 B5 VSB VSB A1, B1, C1, A1, B1, C1, D1, E1 D1, E1 PS_ON PS_ON VSB B4 B4 Load FET, BJT, wire or switch (debounced) to turn on +12V A2, B2 A2, B2 VSB_Return VSB_Return Main Output A5 A5 PS_KILL PS_KILL CURRENT SHARE NOTES 1. Main Output: Current sharing is achieved using the active current share method details.) 2. Current sharing can be achieved with or without the remote (V_SENSE) connected to the common load. 3. +VSB Outputs can be tied together for redundancy but total combined output power must not exceed the rated standby power. The +VSB output has an internal ORING MOSFET for additional redundancy/internal short protection. 4. The current sharing pin B5 is connected between sharing units (forming an ISHARE bus). It is an input and/or an output (bi-directional analogue bus) as the voltage on the line controls the current share between sharing units. A power supply will respond to a change in this voltage but a power supply can also change the voltage depending on the load drawn from it. On a single unit the voltage on the pin (and the common ISHARE bus would read 8VDC at 100% load. For two units sharing the same load this would read 4VDC for perfect current sharing (i.e. 50% load per unit). 5. The load for both the main 12V and the VSB rails at initial startup shall not be allowed to exceed the capability of a single unit. The load can be increased after a delay of 3sec (minimum), to allow all sharing units to achieve steady state regulation. MECHANICAL DIMENSIONS www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 8 of 9 D1U54P-W-650-12-HBxC Series 54mm 1U Front End AC-DC Power Supply Converter 1. AC input connector: IEC 320-C14 2. Dimensions: 2.15" x 9.0" x 1.57" [54.5mm x 228.6mm x 40.0mm] 3. This drawing is a graphical representation of the product and may not show all fine details. 4. Reference File: D1U54P-W-650-12-HBxC (M1876-M1877)_Drawing for Product Datasheet_20160119.pdf OPTIONAL ACCESSORIES Description Part Number MPS Internal Part Number 12V D1U54P Output Connector Card D1U54P-12-CONC 8407001-1 APPLICATION NOTES Document Number Description Link ACAN-64 D1U54P Output Connector Card http://power.murata.com/datasheet?/data/apnotes/acan-64.pdf ACAN-59 D1U54P-x Communication Protocol http://power.murata.com/datasheet?/data/apnotes/acan-59.pdf Murata Power Solutions, Inc. This product is subject to the following operating requirements and the Life and Safety Critical 11 Cabot Boulevard, Mansfield, MA 02048 -1151 Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ U.S.A. Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment ISO 9001 and 14001 REGISTERED constructed in accordance therewith. Specifications are subject to change without notice. © 2016 Murata Power Solutions, Inc. www.murata-ps.com/support D1U54P-W-650-12-HBxC.A02 Page 9 of 9