MVAD065 Series www.murata-ps.com 65W 2" x 4" AC-DC Power Supply Converter DESCRIPTION The MVAD065 series switching power supplies utilize advanced component and circuit technologies to deliver high efficiency. Designed for Medical, Telecom, and Industrial applications to satisfy 1U height design considerations, the MVAD065 Series measures only 2.0” x 4.0” x 1.3”. All models offer universal AC input and compliance to worldwide safety and EMC standards. ORDERING GUIDE Model Number Natural Convection Cooling Main Output (V1) MVAD065-05 55W 5V MVAD065-12 12V 60W MVAD065-18 18V FEATURES MVAD065-24 24V 65W MVAD065-48 48V „„ ITE (2nd Ed.) and Medical (3rd ed.) MOPP safety approved INPUT CHARACTERISTICS „„ 55-65W compact high density Parameter Conditions Min. Typ. Max. Units „„ 2" x 4" standard footprint Single phase 90 120/230 264 Vac Input Voltage Operating Range DC 120 300 Vdc „„ High efficiency up to 90% Input Frequency 47 50/60 63 Hz „„ Remote Sense Turn-on Input Voltage Input rising at full load 70 85 Vac Turn-off Input Voltage Input falling at full load 70 85 „„ Universal AC input Input Current 90Vac input, full load 1.4 A „„ Low profile - 1U package 5V 75 Inrush Current At 264Vac, at 25°C cold start Apk Other 60 „„ Convection-cooled operation up to 65W OUTPUT CHARACTERISTICS „„ Complies with 5000m altitude Main Output Line, Load, Cross Typical Efficiency „„ RoHS compliant Model Number Load Current Load Capacitance Voltage (V1) Regulation @230Vac full load „„ Input power < 74W MVAD065-05 5V 0 to 11A 0 to 2200μF ± 2% 84% MVAD065-12 12V 0 to 5.0A 0 to 1000µF ± 2% 88% „„ UL Class I and II approved MVAD065-18 18V 0 to 3.34A 0 to 680μF ± 2% 86% „„ Less than 0.3W no load input power MVAD065-24 24V 0 to 2.71A 0 to 560µF ± 2% 89% MVAD065-48 48V 0 to 1.36A 0 to 330µF ± 2% 90% „„ Complies with ErP/Energy Star requirement excluding 5V output MAIN OUTPUT CHARACTERISTICS Max. Parameter Conditions Min. Units 5V Other Transient Response 50% load step, 1A/µsec slew rate ±5 % Settling Time to 1% of Nominal 500 200 µsec Turn On Delay After application of input power 1 sec Output Voltage Rise Monotonic, 0 to 100% load 50 msec Setpoint Accuracy 120Vac, 40W, 25°C ±1 ±0.5 % Output Holdup 115Vac, 100% load 10 msec Temperature Coefficient 0.02 %/°C 1 Ripple Voltage & Noise 2 1 % Compensates for up to 400mV of lead drop with remote sense 3 Remote Sense 400 mV connected. Protected against short circuit and reverse connection. 1. Ripple and noise are measured with 0.1 uF of ceramic capacitance and 47 uF of electrolytic capacitance on each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used. Available now at 2. Unless otherwise specified all readings are taken at 120Vac input and 25°C ambient temperature. http://power.murata.com/acdc3d 3. 0.4V lead drop is compensated in remote sense. CB Test Certificate REG.-Nr C457 . For full details go to and Test Report For full details go to www.murata-ps.com/rohs www.murata-ps.com/rohs power.murata.com MVAD065.B01 Page 1 of 7 MVAD065 Series 65W 2" x 4" AC-DC Power Supply Converter ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range -40 85 See thermal derating curves -10 70 °C Operating Temperature Range Start up -20 Operating Humidity Non-condensing 10 95 % For Class I ITE Equipment deployment -200 5000 Operating Altitude m Other -200 2000 MTBF Telcordia SR-332 M1C3 25°C 1M Hours Operating, IEC60068-2-27, half-sine 5G, 6ms, Complies 3 times per face, 6 faces Shock Non-operating, IEC60068-2-27, half-sine, Complies 30G, 18ms, 3 times per face, 6 faces Operating, IEC60068-2-6, 1.0G, 10-150Hz, 10 Complies minutes per axis, on all 3 axes Vibration Non-operating, IEC60068-2-6, 2.0G, Complies 10-150Hz, 10 minutes per axis, on all 3 axes IEC60950-1:2005 (2nd Edition); Am1:2009 UL60950-1 2nd Edition,2011-12-19, CSA C22.2 No. 60950-1-07, 2nd Edition,2011-12 EN60950-1:2006 + A11:2009 + A1:2010 + A12:2011 Safety IEC60601-1:2005 + CORR.1(2006) + CORR.2(2007) ANSI/AAMI ES60601-1 (2005+C1:09 + A2:10), CSA-C22.2 No. 60601-1(2008), MOPP CE Marking per LVD Warranty 2 years Outside Dimensions 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) MVAD065-05 / MVAD065-18 0.285lbs (130g) typical Weight Other 0.27lbs (123g) typical PROTECTION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units MVAD065-05 Latching (50% load) 110 190 Overvoltage Protection %V1 Other Latching (60% load) 110 160 Overcurrent Protection Hiccup mode 110 160 %A ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Primary to Earth Ground (1xMOPP) 1500 Vac 4 Isolation Primary to Secondary (2xMOPP) 4000 Secondary to Earth Ground 500 Vdc 240Vac, 60Hz, 25°C 300 Leakage Current (under normal conditions) 264Vac, 60Hz, 25°C 350 µA Touch Current 264Vac, 60Hz, 25°C 100 EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics IEC/EN 61000-3-2 Class A Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Complies EN 55022 Class B, Class A (at Class II equipment) Conducted Emissions FCC Part 15 Class B, Class A (at Class II equipment) ESD Immunity IEC/EN 61000-4-2 Level 4, Criterion A Radiated Field Immunity IEC/EN 61000-4-3 Level 2, Criterion A Electrical Fast Transient Immunity IEC/EN 61000-4-4 Level 3, Criterion A Surge Immunity IEC/EN 61000-4-5 Level 4, Criterion A RF Conducted Immunity IEC/EN 61000-4-6 Level 2, Criterion A Magnetic Field Immunity IEC/EN 61000-4-8 Level 2, Criterion A Voltage dips, interruptions IEC/EN 61000-4-11 Level 3, Criterion B 4. At class I equipment. power.murata.com MVAD065.B01 Page 2 of 7 MVAD065 Series 65W 2" x 4" AC-DC Power Supply Converter EMI CONSIDERATIONS For optimum EMI performance, the power supply should be mounted to a metal plate grounded to all 4 mounting holes of the power supply. To comply with safety standards, this plate must be properly grounded to protective earth (see mechanical dimension notes). Pre-compliance testing has shown the stand- alone power supply to comply with EN55022 class A radiated emissions. Radiated emission results vary with system enclosure and cable routing paths. SAFETY CONSIDERATIONS 1. This power supply is a component level power supply intended for use in class I or class II applications. Secondary ground traces need to be suit- ably isolated from primary ground traces when used in class II applications. 2. When the power supply is used in class II equipment, all ground traces and components connected to the primary side are considered primary for spacing and insulation considerations. 3. Double pole/neutral fusing. PERFORMANCE DATA MVAD065-05 Efficiency (%) MVAD065-12 Efficiency (%) 93 95 93 91 91 89 89 87 87 85 85 83 83 90Vac 81 90Vac 81 115Vac 79 115Vac 230Vac 79 77 230Vac 264Vac 77 75 264Vac 75 73 0.00 1.00 2.00 3.00 4.00 5.00 0.00 2.00 4.00 6.00 8.00 10.00 12.00 Output Current (A) Output Current (A) MVAD065-18 Efficiency (%) MVAD065-24 Efficiency (%) 95 95 93 93 91 91 89 89 87 87 85 85 83 90Vac 83 90Vac 115Vac 81 81 115Vac 230Vac 79 230Vac 79 264Vac 77 264Vac 77 75 75 0.00 0.50 1.00 1.50 2.00 2.50 3.00 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 Output Current (A) Output Current (A) MVAD065-48 Efficiency (%) 95 93 91 89 87 85 83 90Vac 115Vac 81 230Vac 79 264Vac 77 75 0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 Output Current (A) power.murata.com MVAD065.B01 Page 3 of 7 MVAD065 Series 65W 2" x 4" AC-DC Power Supply Converter PERFORMANCE DATA Thermal Derating (Other) MVAD065-05 Thermal Derating 60 100 50 80 40 60 30 40 20 20 10 0 0 -10 10 30 50 70 -10 10 30 50 70 Ambient temp. ( ) Ambient temp. ( ) Inrush waveform (AC264V 25°C) power.murata.com MVAD065.B01 Page 4 of 7 Output power (W) Output power (%) MVAD065 Series 65W 2" x 4" AC-DC Power Supply Converter MECHANICAL DIMENSIONS – MVAD065-05 ONLY Output Voltage Adjust Pot for Factory Use Φ0.156±0.05 4 Places Maximum Screw Head DIAMETER Maximum earth ground contact area PCB top and bottom DIAMETER Φ0.236" (6.0) ※1 Preferred screw type M3 (Metric screw threads) No.4-40UNC (United thread Standard) All dimensions in inches (mm). tolerance is +/-0.02’ (0.5) Mounting holes H1 and H2 should be earth-grounded for EMI purpose Mounting holes H2 is earth ground connection This power supply requires mounting on standoffs minimum 0.2' (5.0) in height Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS PIN Description Mating Housing Crimp terminal/pins Input Connector CN1 : Molex 26-62-4030 1 AC Line (V-) Molex 09-50-8031 with locking ramp Molex 6838 Series 3 AC Neutral (V+) Spade Connector: #250 GND Earth Ground Output Connector CN2 : Molex 26-60-4060 1, 2 V1 3, 4 DC Return Molex 09-50-8061 with locking ramp Molex 6838 Series 5 -Remote Sense (NC) 6 +Remote Sense power.murata.com MVAD065.B01 Page 5 of 7 MVAD065 Series 65W 2" x 4" AC-DC Power Supply Converter MECHANICAL DIMENSIONS – MVAD065-12x ONLY All dimensions in inches (mm). tolerance is +/-0.02’ (0.5) Mounting holes H1 and H2 should be earth-grounded for EMI purpose Mounting holes H2 is earth ground connection This power supply requires mounting on standoffs minimum 0.2' (5.0) in height Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS PIN Description Mating Housing Crimp terminal/pins Input Connector CN1 : Molex 26-62-4030 1 AC Line (V-) Molex 09-50-8031 with locking ramp Molex 6838 Series 3 AC Neutral (V+) Spade Connector: #250 GND Earth Ground Output Connector CN2 : Molex 26-60-4060 1, 2 V1 3, 4 DC Return Molex 09-50-8061 with locking ramp Molex 6838 Series 5 -Remote Sense (NC) 6 +Remote Sense power.murata.com MVAD065.B01 Page 6 of 7 MVAD065 Series 65W 2" x 4" AC-DC Power Supply Converter MECHANICAL DIMENSIONS – MVAD065-xx 24V and 48V MODELS All dimensions in inches (mm). tolerance is +/-0.02’ (0.5) Mounting holes H1 and H2 should be earth-grounded for EMI purpose Mounting holes H2 is earth ground connection This power supply requires mounting on standoffs minimum 0.2' (5.0) in height Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS PIN Description Mating Housing Crimp terminal/pins Input Connector CN1 : Molex 26-62-4030 1 AC Line (V-) Molex 09-50-8031 with locking ramp Molex 6838 Series 3 AC Neutral (V+) Spade Connector: #250 GND Earth Ground Output Connector CN2 : Molex 26-60-4060 1, 2 V1 3, 4 DC Return Molex 09-50-8061 with locking ramp Molex 6838 Series 5 -Remote Sense (NC) 6 +Remote Sense This product is subject to operating requirements and the Life and Murata Manufacturing Co., Ltd. Power Device Product Division Safety Critical Application Policy. Click here to view policy. Nagaokakyo-shi, Kyoto 617-8555 Japan Please contact us regarding restricted materials compliance beyond ISO 9001 and 14001 REGISTERED the RoHS directive. Murata makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards that anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm, and take appropriate remedial actions. Buyer will fully indemnify Murata, its affiliated companies, and its representatives against any damages arising out of the use of any Murata products in safety-critical applications. Specifications are subject to change without notice. © 2015 Murata Manufacturing Co., Ltd. All Rights Reserved. power.murata.com MVAD065.B01 Page 7 of 7