MURATA POWER SOLUTIONS S1U-3X-16-A-48-RC

S1U-3X www.murata-ps.com 1U 19 inch Power Shelf for D1U Power Supplies SELECTION GUIDE Part Number Description S1U-3X-16-A-12-RC Power shelf for 12V D1U S1U-3X-16-A-48-RC Power shelf for 48V D1U OUTPUT AND PROTECTION CHARACTERISTICS Parameter Output total regulation Please Refer to Appropriate D1U Datasheet on www.murata-ps.com Output ripple voltage & noise 12V 1200W: CPS_D1U-W-1200-12.pdf FEATURES Output current operating range 12V 1600W: CPS_D1U-W-1600-12.pdf n RoHS compliant 48V 1200W: CPS_D1U-W-1200-48.pdf Output total regulation n 1U height, 18.3” width, 16” depth powershelf 48V 1600W: CPS_D1U-W-1600-48.pdf Output ripple voltage & noise 48V 2000W: CPS_D1U-W-2000-48.pdf n Holds 3 D1U series power supplies Output current operating range n Hot insertion / removal Efficiency D1U Family Part Numbering n Blind-docking connection Start-up time D1U-W-1200-12-HA1C n Lug DC output connection for 2 AWG cables Transient response main output 2 n I C interface Transient response standby output D = Distributed Power C = RoHS compliant Current sharing accuracy n Signal connector (up to 3 in parallel with 5A total 1U = 1U 1 = Airflow front to back, minimum current) n Optional shelf to shelf signal connector (up 2 = Airflow back to front Hold-up time W = Wide AC input to 2 shelves in parallel) Standby Output Voltage A=5V, B=12V, C=3.3V, Over-temperature (Auto-restart) 1200 = 1200 Watts 0=no standby DESCRIPTION Over voltage main output (Latching) 1600 = 1600 Watts 2000 = 2000 Watts (only H = Hotplug connector Over voltage standby output (Latching) The S1U-X3 is a 1U x 19” EIA Rack Mount Power available in 48V output model) Shelf designed for holding three 12V or 48V D1U Over current main output (Latching) 12 = Main output 12V Front End Power Supplies in current sharing 48 = Main output 48V Over current standby output (Latching) applications. It is intended for distributed power 1 architecture applications in the Servers, Storage EMISSIONS & IMMUNITY (with power supplies inserted) Networking and Data Communications markets. There Conditions Description Criteria are two lug terminal connections for #2 AWG cabling Harmonics IEC/EN 61000-3-2 for the DC output. System connection through the Voltage fluctuation & flicker IEC/EN 61000-3-3 2 I C bus reports the performance status of the power Emission conducted FCC 47 CFR Parts 15 / CISPR 22 / EN 55022 Class A, 6dB margin supplies within the power shelf. Two Power Shelves Emission radiated FCC 47 CFR Parts 15 / CISPR 22 / EN 55022 Class A, 6dB margin can operate in parallel by an optional Shelf-to-Shelf 4kV contact discharge cable, doubling the power output to the maximum ESD IEC/EN 61000-4-2 8kV operational air discharge capability of 9.6kW for two 12V power shelves or 15kV non-operational air discharge 12kW for two 48V power shelves. Electromagnetic field IEC/EN 61000-4-3 Electrical fast transients/burst IEC/EN 61000-4-4 Surge IEC/EN 61000-4-5 1kV/2kV, performance criteria B 3 Vac, 80% AM, 1kHz, RF Conducted immunity IEC/EN 61000-4-6 Performance criteria A Magnetic immunity IEC/EN 61000-4-8 3A/m Voltage dips, interruptions IEC/EN 61000-4-11 SAFETY Parameter Condition Agency approvals c-CSA-us (CSA 60950-1-03/UL 60950-1,first edition) For full details go to Material flammability UL 94V-0 www.murata-ps.com/rohs 1 Product is designed to meet the referenced standards. www.murata-ps.com/support CPS_S1U-3X.D02 Page 1 of 4 Standby output Main output set point set point S1U-3X 1U 19 inch Power Shelf for D1U Power Supplies GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range Non-condensing -40 70 °C Operating Temperature Range 0 50 Operating Humidity Non-condensing 10 90 % Storage Humidity 5 90 Shock 30G non operating Sinusoidal Vibration 0.5G, 5 – 500 Hz 5 Calculated per Bellcore at Ta=30°C 200 x10 hrs MTBF 5 Demonstrated 200 x10 hrs CONNECTOR TO CUSTOMER SYSTEM Signal Connector: MOLEX # 39-28-5204 OR TYCO # 281282-1 High Level Pin Assignment Signal Name Description I Max Low Level open drain - 2 mA 1 1 AC_OK1 Input AC Voltage ‘OK’ signal output for the shelf < 0.7V + 4 mA open drain - 2 mA 2 2 P_Good1 Power good signal output for the shelf < 0.7V + 4 mA > 2.1V (open, or Vsb) - 1 mA 3 3 PS_On1 Power enable for the shelf < 0.7V (active, PS:On) - 4 mA 4 NOT USED open drain - 2 mA 1 5 AC_OK0 Input AC Voltage “OK” signal output for the shelf < 0.7V + 4 mA open drain - 2 mA 2 6 P_Good0 Power good signal output for the shelf < 0.7V + 4 mA > 2.1V (open, or Vsb) - 1 mA 3 7 PS_OnO Power enable for the shelf < 0.7V (active, PS:On) - 4 mA 8 NOT USED > 2.1V, < Vsb 2 9 I C Adr2 Address input 2 ± 1 mA < 0.8V 2 4 2 10 I C Clock I C serial clock bus Vsb 2 4 2 11 I C Data I C serial data bus Vsb 12 I_SHARE 5 13 SENSE + 5 14 SENSE - 15 Vsb Standby voltage output 16 Vsb Standby voltage output 17 Vsb Standby voltage output 18 GND GROUND 19 GND GROUND 20 GND GROUND All control signals are with respect to Ground. Negative currents exit the power supply. 1 Signal goes low when any one of the three power supplies loses AC 2 Signal goes low when any one of the three power supplies fail 3 2 Pull this pin to GND to turn on three power supplies at the same time. Use I C to turn on one power supply at a time. 4 Recomended 10KOhm pull up resistor to host 3.3 or 5V rail 5 Short Sense+ to +Vout and Sens- to GND at the point of load www.murata-ps.com/support CPS_S1U-3X.D02 Page 2 of 4 S1U-3X 1U 19 inch Power Shelf for D1U Power Supplies SHELF TO SHELF CONNECTION Signal Connector: MOLEX # 39-28-5164 OR TYCO # 281281-1 High Level Pin Assignment Signal Name Description I Max Low Level open drain - 2 mA 1 1 AC_OK1 Input AC Voltage ‘OK’ signal output for the shelf < 0.7V + 4 mA open drain - 2 mA 2 2 P_Good1 Power good signal output for the shelf + 4 mA < 0.7V > 2.1V (open, or Vsb) - 1 mA 3 3 PS_On1 Power enable for the shelf < 0.7V (active, PS:On) - 4 mA 4 NOT USED 5 NOT USED 2 4 2 6 I C Clock I C serial clock bus Vsb 2 4 2 7 I C Data I C serial data bus Vsb 8 I_SHARE 5 9 SENSE + 5 10 SENSE - 11 Vsb Standby voltage output 12 Vsb Standby voltage output 13 Vsb Standby voltage output 14 GND GROUND 15 GND GROUND 16 GND GROUND All control signals are with respect to Ground. Negative currents exit the power supply. 1 Signal goes low when any one of the three power supplies loses AC 2 Signal goes low when any one of the three power supplies fail 3 2 Pull this pin to GND to turn on three power supplies at the same time. Use I C to turn on one power supply at a time. 4 Recomended 10KOhm pull up resistor to host 3.3 or 5V rail 5 Short Sense+ to +Vout and Sens- to GND at the point of load OPTIONAL ACCESSORIES Description Murata-PS Part Number Shelf to Shelf Cable 535-413-1537-1 www.murata-ps.com/support CPS_S1U-3X.D02 Page 3 of 4 S1U-3X 1U 19 inch Power Shelf for D1U Power Supplies MECHANICAL DIMENSIONS 17.315 (439.80) NOTES: 1. The DC output terminals are of terminal block style that will allow connection using crimp type right-angle lugs accepting up to AWG#2 wire, Panduit lug LCC2-14AWF-Q or equivalent is recommended. 2. Two M6 studs at 15.88 mm centre spacing are provided for connection to each pole. Hardware is 18.307 (465.00) provided for fastening the lugs/wires as well as terminal block covers 18.992 (482.40) PRODUCT LABEL INFORMATION S1U-3X-16-A-xx-RC v v = factory control character (not required for ordering) S = Shelf C = RoHS 1U =1U height R = Reserve 3X = 3 unit per shelf xx = 12V xx = 48V 16 = 16” depth A = AC input D = DC input This product is subject to the following operating requirements Murata Power Solutions, Inc. and the Life and Safety Critical Application Sales Policy: 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Refer to: http://www.murata-ps.com/requirements/ ISO 9001 and 14001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2017 Murata Power Solutions, Inc. www.murata-ps.com/support CPS_S1U-3X.D02 Page 4 of 4 1.709 15.937 (43.40) (404.80) 1.252 0.228 (31.80) (5.80)