MURATA POWER SOLUTIONS SPM15-050-Q12P-C

MURATA www.murata-ps.com SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters Typical unit FEATURES PRODUCT OVERVIEW  Wide range input voltages 9-36 and 18-75 Vdc The SPM15 series isolated DC-DC converters converters offer a feature/option set including: represent the next generation in Industrial Potted through-hole mounting, positive or negative logic  1˝ x 1˝ x 0.41˝ Dimensions. Module Technology. Featuring a full 15-Watt output (remote on/off), over-current & over-temperature  Adjustable Vout (+10% to -10%) in one square inch of board area, the SPM15 series protection, under-voltage lockout. The input voltage  High Effi ciency isolated DC-DC converter family offers effi cient range covers the standard Industrial requirements regulated DC power for printed circuit board with a regulated output voltage and power rating  Positive & Negative logic, Remote On/Off mounting. The 1˝ x 1˝ x 0.41˝ (25.4 x 25.4 x 10.41 up to 15W. control Option mm) converter accepts a wide range of input volt-  Modules provide voltage isolation (basic Monotonic startup ages, ideal for industrial applications. insulation) from input to output of up to 1600V. The  Continuous Short Circuit protection Intended target markets include transportation, Operating Ambient Temperature Range is -40°C  Over-temperature protection medical systems, electronic test equipment, indus- to +85°C.The Module delivers full output power  trial processing equipment, industrial applications to +70°C with no airfl ow. These parts are ideal for Over-Voltage protection where power modules must meet rugged envi- applications that do not require any heat sinking or  Low output ripple and noise ronmental requirements, high power density, and forced air cooling.  Strong thermal derating characteristics where isolated output voltages are required. These  Operational Temperature Range –40°C to +85°C  1600V I/O isolation  Packaged in a fi ve-sided EMI shielding metal package with non-conductive base  Certifi ed to UL 60950-1, CAN/CSA-C22.2 No. 60950-1, IEC60950-1, safety approvals, 2nd edition, with AM1 For full details go to www.murata-ps.com/rohs www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 1 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters ➀ ➂ PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE Output Input R/N (mVp-p) Regulation (Max.) Effi ciency (%) Dimensions IOUT Total IIN, IIN, VOUT (A, Power VIN Nom. Range min. load full load Root Models ➀ (V) max) (W) Typ. ➁ Max. Line Load (V) (V) (mA) (A) Min. Typ. Case (inches) Case (mm) SPM15-033-Q12 3.3 4.5 14.85 60 100 ±0.25 ±0.25 24 9-36 100 0.695 86.5 89 1.0 x 1.0 x 0.41 25.4 x 25.4 x 10.41 SPM15-033-Q48 3.3 5 16.5 30 60 ±0.25 ±0.25 48 18-75 60 0.76 88.5 90 1.0 x 1.0 x 0.41 25.4 x 25.4 x 10.41 SPM15-050-Q12 5 3 15 40 70 ±0.05% ±0.1% 24 9-36 105 0.71 85.5 88 1.0 x 1.0 x 0.41 25.4 x 25.4 x 10.41 SPM15-050-Q48 5 3 15 60 95 ±0.3% ±0.2% 48 18-75 56 0.35 86.5 88.5 1.0 x 1.0 x 0.41 25.4 x 25.4 x 10.41 SPM15-120-Q12 12 1.3 15.6 60 120 ±0.05% ±0.1% 24 9-36 110 0.77 82.3 84 1.0 x 1.0 x 0.41 25.4 x 25.4 x 10.41 SPM15-120-Q48 12 1.3 15.6 85 120 ±0.075% ±0.05% 48 18-75 56 0.76 82 84 1.0 x 1.0 x 0.41 25.4 x 25.4 x 10.41 SPM15-150-Q12 15 1.1 16.5 130 175 ±0.1% ±0.1% 24 9-36 130 0.82 82.5 84 1.0 x 1.0 x 0.41 25.4 x 25.4 x 10.41 SPM15-150-Q48 15 1.1 16.5 80 150 ±0.1% ±0.075% 48 18-75 60 0.41 83 84.5 1.0 x 1.0 x 0.41 25.4 x 25.4 x 10.41 Notes: ➀ Please refer to the part number structure for additional options and complete order- ➂ All specifi cations are at nominal line voltage and full load, +25 °C. unless otherwise ing part numbers. noted. See detailed specifi cations for full conditions. ➁ Ripple and Noise is shown at 20 MHz bandwidth. INPUT/OUTPUT EXTERNAL TEST CAPACITORS Model Input Capacitor (electrolytic) Output Capacitor(s) SPM15-033-Q12 100 μF SPM15-033-Q48 4.7 μF SPM15-050-Q12 100 μF SPM15-050-Q48 4.7 μF 1μF ceramic & 10μF tantalum SPM15-120-Q12 100 μF SPM15-120-Q48 4.7 μF SPM15-150-Q12 100 μF SPM15-150-Q48 4.7 μF PART NUMBER STRUCTURE SPM15- 120 - Q48 P Lx - C Single Output Potted Module RoHS-6 Hazardous Substance Compliance 15-Watt Series (Does not claim EU RoHS exemption 7b, lead in solder) Nominal Output Voltage Pin Length Option (through-hole only) in Tenths of a Volt Blank = Std. pin length 0.15˝ (3.8mm) (033 = 3.3V, 050 = 5V, L1 = 0.110˝ (2.79mm) ➀ 120 = 12V, 150 = 15V) On/Off Control Logic Input Voltage Range Blank = No On/Off & no Trim Q12 = 9-36 Vdc P = Positive Q48 = 18-75Vdc N = Negative ➀ Special quantity order is required; samples available with standard pin length only. ➁ Some model number combinations may not be available. See website or contact your local Murata sales representative. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr P operly and r age 2 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS – MODEL SPM15-033-Q12 ABSOLUTE MAXIMUM RATINGS Conditions ➀ Minimum Typical/Nominal Maximum Units Input Voltage, Continuous 0 36 Vdc Input Voltage, Transient 100 mS max. duration 50 Vdc Isolation Voltage Input to output 1600 Vdc On/Off Remote Control Power on, referred to -Vin 0 15 Vdc Output Power 1.46 15.07 W Output Current Current-limited, no damage, short-circuit protected 0.45 4.5 A Storage Temperature Range Vin = Zero (no power) -55 125 ˚C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifi cations Table is not implied or recommended. INPUT Operating Voltage Range 9 24 36 Vdc Recommended External Fuse Fast blow 4 A Start-up Threshold Rising input voltage 8 8.5 9 Vdc Undervoltage Shutdown (50% load) Falling input voltage 7.7 8.3 8.9 Vdc Internal Filter Type C Input Current Full Load Input Current Vin = nominal 0.695 0.726 A Low Line Input Current Vin = minimum 1.89 1.947 A Inrush Transient 0.05 A2-Sec. Short Circuit Input Current 50 100 A Minimum Load Input Current Iout = minimum, unit=ON 100 125 mA Shut-Down Input Current (Off, UV, OT) 1 2 mA Refl ected (Back) Ripple Current ➁ Measured at input with specifi ed fi lter 30 50 mA, p-p GENERAL and SAFETY Vin = 24V, full load 86.5 89 % Effi ciency Vin = min., full load 86 87.3 % Isolation Isolation Voltage Input to output 1600 Vdc Isolation Resistance 10 MΩ Isolation Capacitance 1500 pF Certifi ed to UL-60950-1, CSA-C22.2 No. 60950- Safety Yes 1, IEC/60950-1, 2nd edition, with AM1 Per Telcordia SR332, issue 1, class 3, ground 6 Calculated MTBF 2 Hours x 10 fi xed, Tambient = +25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 325 350 375 KHz Startup Time Power on to Vout regulated 50 mS Startup Time Remote ON to Vout regulated 50 mS 50-75-50% load step, settling time to within Dynamic Load Response 60 100 μSec 1% of Vout Dynamic Load Peak Deviation same as above ±75 ±150 mV FEATURES and OPTIONS Remote On/Off Control ➂ “N” suffi x Negative Logic, ON state ON = Ground pin -0.7 0.8 V Negative Logic, OFF state OFF = Pin open 10 15 V Control Current Open collector/drain 1 mA “P” suffi x Positive Logic, ON state ON = Pin open 10 15 V Positive Logic, OFF state OFF = Ground pin -0.7 0.7 V Control Current Open collector/drain 1 mA www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 3 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) – MODEL SPM15-033-Q12 OUTPUT Conditions ➀ ➂ Minimum Typical/Nominal Maximum Units Total Output Power 1.46 14.85 15.07 W Voltage Nominal Output Voltage No trim 3.251 3.3 3.35 Vdc Setting Accuracy At 50% load, no trim -1.5 1.5 % of Vnom Output Voltage Range User-adjustable -10 10 % of Vnom Overvoltage Protection Via magnetic feedback 3.7 4.9 5.4 Vdc Current Output Current Range 0.45 4.5 4.5 A Current Limit Inception 98% of Vnom., after warmup 4.9 7.5 8.5 A Short Circuit Hiccup technique, autorecovery within Short Circuit Current 0.321 A ±1.25% of Vout Short Circuit Duration (remove short for Output shorted to ground, no damage Continuous recovery) Short circuit protection method Current limiting Regulation Line Regulation Vin = min. to max., Vout = nom., Iout = nom. ±0.25 % of Vout Load Regulation Iout = min. to max., Vin = 24V ±0.25 % of Vout Ripple and Noise 5 Hz- 20 MHz BW, Vin=24V 60 90 mV pk-pk Maximum Capacitive Loading Low ESR 1000 μF MECHANICAL Outline Dimensions 1 x 1 x 0.41 Inches (Please refer to outline drawing) WxLxH 25.4 x 25.4 x 10.41 mm Weight 0.69 Ounces 19.56 Grams Through Hole Pin Diameter 0.04 Inches 1.016 mm Through Hole Pin Material Copper alloy TH Pin Plating Metal and Thickness Nickel subplate 50 μ-inches Gold overplate 5 μ-inches ENVIRONMENTAL Operating Ambient Temperature Range See derating -40 85 °C Operating Case Temperature Range No derating -40 85 °C Case Material Tin plated steel with black powder coat Storage Temperature Vin = Zero (no power) -55 125 °C Thermal Protection/Shutdown Measured in center 110 115 120 °C Electromagnetic Interference External fi lter is required Conducted, EN55022/CISPR22 B Class RoHS rating RoHS-6 Notes ➀ Unless otherwise noted, all specifi cations are at nominal input voltage, nominal out- ➁ Input (back) ripple current is tested and specifi ed over 5 Hz to 20 MHz bandwidth. put voltage and full load. General conditions are +25˚ Celsius ambient temperature, Input fi ltering is Cbus=220 μF, Cin=33 μF and Lbus=12 μH. near sea level altitude, natural convection airfl ow. All models are tested and specifi ed ➂ The Remote On/Off Control is referred to -Vin. with external parallel 1 μF and 10 μF output capacitors. The external input capacitor is 100 μF, electrolytic. All capacitors are low-ESR types wired close to the converter. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 4 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-033-Q12 Effi ciency vs. Line Voltage and Load Current @ 25°C Power Dissipation 90 2.50 88 86 2.25 84 82 2.00 80 VIN = 9V 78 VIN = 12V 76 1.75 VIN = 24V 74 72 VIN = 36V 1.50 70 68 1.25 66 VIN = 9V 64 VIN = 12V 1.00 62 60 VIN = 24V 58 0.75 VIN = 36V 56 54 0.50 52 0.5 0.9 1.4 1.8 2.3 2.7 3.2 3.6 4.1 4.5 0.5 0.9 1.4 1.8 2.3 2.7 3.2 3.6 4.1 4.5 Output Load Current (Amps) Load Current (Amps) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 9V, 12V, or 24V (air fl ow from Pin J1 to Pin J2 on PCB) Vin = 36V (air fl ow from Pin J1 to Pin J2 on PCB) 5 5 .5 m/s (100 LFM) 4 4 Natural Convection 3 3 2 2 1 1 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr P operly and r age 5 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om Output Current (Amps) Efficiency (%) Output Current (Amps) Power Dissipation (Watts) MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS – MODEL SPM15-033-Q48 ABSOLUTE MAXIMUM RATINGS Conditions ➀ Minimum Typical/Nominal Maximum Units Input Voltage, Continuous 0 80 Vdc Input Voltage, Transient 100 mS max. duration 100 Vdc Isolation Voltage Input to output 1600 Vdc On/Off Remote Control Power on, referred to -Vin 0 15 Vdc Output Power 1.63 16.75 W Output Current Current-limited, no damage, short-circuit protected 0.5 5 A Storage Temperature Range Vin = Zero (no power) -55 125 ˚C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifi cations Table is not implied or recommended. INPUT Operating Voltage Range 18 48 75 Vdc Recommended External Fuse Fast blow 2 A Start-up Threshold Rising input voltage 15.5 16.9 17.9 Vdc Undervoltage Shutdown (50% load) Falling input voltage 15 16 16.8 Vdc Internal Filter Type C Input Current Full Load Input Current Vin = 24V 0.764 0.788 A Full Load Input Current Vin = 48V 0.388 0.403 A Low Line Input Current Vin = minimum 1.03 1.04 A Inrush Transient 0.05 A2-Sec. Short Circuit Input Current 0.05 0.1 A Minimum Load Input Current Iout = minimum, unit=ON 60 90 mA Shut-Down Input Current (Off, UV, OT) 1 2 mA Refl ected (Back) Ripple Current ➁ Measured at input with specifi ed fi lter 30 mA, p-p GENERAL and SAFETY Vin = 24V, full load 88.5 90 % Effi ciency Vin = 48V, full load 86.5 88.5 % Isolation Isolation Voltage Input to output 1600 Vdc Isolation Resistance 10 MΩ Isolation Capacitance 1500 pF Certifi ed to UL-60950-1, CSA-C22.2 No. 60950- Safety Yes 1, IEC/60950-1, 2nd edition, with AM1 Per Telcordia SR332, issue 1, class 3, ground Calculated MTBF 2,000,000 Hours fi xed, Tambient = +25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 325 350 375 KHz Startup Time Power on to Vout regulated 10 50 mS Startup Time Remote ON to Vout regulated 10 50 mS 50-75-50% load step, settling time to within Dynamic Load Response 75 150 μSec 1% of Vout Dynamic Load Peak Deviation same as above ±75 ±125 mV FEATURES and OPTIONS Remote On/Off Control ➂ “N” suffi x Negative Logic, ON state ON = Ground pin -0.7 0.8 V Negative Logic, OFF state OFF = Pin open 10 15 V Control Current Open collector/drain 1 mA “P” suffi x Positive Logic, ON state ON = Pin open 10 15 V Positive Logic, OFF state OFF = Ground pin -0.7 0.7 V Control Current Open collector/drain 1 mA www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 6 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) – MODEL SPM15-033-Q48 OUTPUT Conditions ➀ ➂ Minimum Typical/Nominal Maximum Units Total Output Power 1.63 16.5 16.75 W Voltage Nominal Output Voltage No trim 3.2505 3.3 3.3495 Vdc Setting Accuracy At 50% load, no trim 1.5 % of Vnom Output Voltage Range User-adjustable -10 10 % of Vnom Overvoltage Protection Via magnetic feedback 4 5 5.6 Vdc Current Output Current Range 0.5 5 5 A Current Limit Inception 98% of Vnom., after warmup 5.9 7.3 8.4 A Short Circuit Hiccup technique, autorecovery within Short Circuit Current 0.3 A ±1.25% of Vout Short Circuit Duration (remove short for Output shorted to ground, no damage Continuous recovery) Short circuit protection method Current limiting Regulation Line Regulation Vin = min. to max., Vout = nom., Iout = nom. ±0.25 % of Vout Load Regulation Iout = min. to max., Vin = 48V ±0.25 % of Vout Ripple and Noise 20 MHz BW, Vin = 48V 30 60 mV pk-pk Temperature Coeffi cient At all outputs 0.02 % of Vnom./°C Maximum Capacitive Loading Low ESR 5000 μF MECHANICAL Outline Dimensions 1 x 1 x 0.41 Inches (Please refer to outline drawing) WxLxH 25.4 x 25.4 x 10.41 mm Weight 0.69 Ounces 19.56 Grams Through Hole Pin Diameter 0.04 Inches 1.016 mm Through Hole Pin Material Copper alloy TH Pin Plating Metal and Thickness Nickel subplate 50 μ-inches Gold overplate 5 μ-inches ENVIRONMENTAL Operating Ambient Temperature Range See derating -40 85 °C Case Material Tin plated steel with black powder coat Storage Temperature Vin = Zero (no power) -55 125 °C Thermal Protection/Shutdown Measured in center 120 130 140 °C Electromagnetic Interference External fi lter is required Conducted, EN55022/CISPR22 B Class RoHS rating RoHS-6 Notes ➀ Unless otherwise noted, all specifi cations are at nominal input voltage, nominal out- ➁ Input (back) ripple current is tested and specifi ed over 5 Hz to 20 MHz bandwidth. put voltage and full load. General conditions are +25˚ Celsius ambient temperature, Input fi ltering is Cbus=220 μF, Cin=33 μF and Lbus=12 μH. near sea level altitude, natural convection airfl ow. All models are tested and specifi ed ➂ The Remote On/Off Control is referred to -Vin. with external parallel 1 μF and 10 μF output capacitors. The external input capacitor is 100 μF, electrolytic. All capacitors are low-ESR types wired close to the converter. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 7 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-033-Q48 Effi ciency vs. Line Voltage and Load Current @ 25°C Power Dissipation 92 3 90 88 2.5 86 84 2 82 80 VIN = 18V 78 1.5 VIN = 24V 76 VIN = 48V 74 VIN = 18V VIN = 75V 1 72 VIN = 24V 70 VIN = 48V 68 0.5 VIN = 75V 66 64 0 62 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.51 11 1.51 21 2.51 31 3.51 41 4.51 52 Output Load Current (Amps) Load Current (Amps) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 18V, 24V, 36V, 48V, or 60V (air fl ow from Pin J1 to Pin J3 on PCB) Vin 75 (air fl ow from Pin J1 to Pin J3 on PCB) 6 6 5 5 .5 m/s (100 LFM) Natural Convection Natural Convection 4 4 3 3 2 2 1 1 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr P operly and r age 8 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om Output Current (Amps) Efficiency (%) Output Current (Amps) Power Dissipation (Watts) MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS – MODEL SPM15-050-Q12 ABSOLUTE MAXIMUM RATINGS Conditions ➀ Minimum Typical/Nominal Maximum Units Input Voltage, Continuous 0 36 Vdc Input Voltage, Transient 100 mS max. duration 50 Vdc Isolation Voltage Input to output 1600 Vdc On/Off Remote Control Power on, referred to -Vin 0 15 Vdc Output Power 1.48 15.23 W Output Current Current-limited, no damage, short-circuit protected 0.30 3 A Storage Temperature Range Vin = Zero (no power) -55 125 ˚C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifi cations Table is not implied or recommended. INPUT Operating Voltage Range 9 24 36 Vdc Recommended External Fuse Fast blow 4 A Start-up Threshold Rising input voltage 8 8.6 9 Vdc Start up Threshold @-40°C 9.5 10.0 10.5 Vdc Undervoltage Shutdown Falling input voltage 7.8 8.25 9 Vdc Internal Filter Type C Input Current Full Load Input Current Vin = nominal 0.71 0.73 A Low Line Input Current Vin = minimum 1.91 1.97 A 2 Inrush Transient 0.05 A -Sec. Short Circuit Input Current 50 100 mA Minimum Load Input Current Iout = minimum, unit=ON 105 135 mA Shut-Down Input Current (Off, UV, OT) 1 2 mA Refl ected (Back) Ripple Current ➁ Measured at input with specifi ed fi lter 30 mA, p-p GENERAL and SAFETY Vin = 24V, full load 85.5 88 % Effi ciency Vin = min., full load 86 87.3 % Isolation Isolation Voltage Input to output 1600 Vdc Isolation Resistance 10 MΩ Isolation Capacitance 1500 pF Certifi ed to UL-60950-1, CSA-C22.2 No. 60950- Safety Yes 1, IEC/60950-1, 2nd edition, with AM1 Per Telcordia SR332, issue 1, class 3, ground 6 Calculated MTBF 6.2 Hours x 10 fi xed, Tambient = +25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 330 350 370 KHz Startup Time Power on to Vout regulated 50 mS Startup Time Remote ON to Vout regulated 50 mS 50-75-50% load step, settling time to within Dynamic Load Response 100 150 μSec 1% of Vout Dynamic Load Peak Deviation same as above ±85 ±125 mV FEATURES and OPTIONS Remote On/Off Control ➂ “N” suffi x Negative Logic, ON state ON = Ground pin -0.7 0.8 V Negative Logic, OFF state OFF = Pin open 10 15 V Control Current Open collector/drain 1 mA “P” suffi x Positive Logic, ON state ON = Pin open 10 15 V Positive Logic, OFF state OFF = Ground pin -0.7 0.7 V Control Current Open collector/drain 1 mA www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 9 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) – MODEL SPM15-050-Q12 OUTPUT Conditions ➀ ➂ Minimum Typical/Nominal Maximum Units Total Output Power 1.48 15 15.23 W Voltage Nominal Output Voltage No trim 4.925 5 5.075 Vdc Setting Accuracy At 50% load, no trim -1.5 1.5 % of Vnom Output Voltage Range User-adjustable -10 10 % of Vnom. Overvoltage Protection Via magnetic feedback 5.75 5.9 7 Vdc Current Output Current Range 0.3 3 3 A Current Limit Inception 98% of Vnom., after warmup 3.5 4.75 6.5 A Short Circuit Hiccup technique, autorecovery within Short Circuit Current 0.3 A ±1.25% of Vout Short Circuit Duration (remove short for Output shorted to ground, no damage Continuous recovery) Short circuit protection method Current limiting Regulation Line Regulation Vin = min. to max., Vout = nom., Iout = nom. ±0.05 % of Vout Load Regulation Iout = min. to max., Vin = 24V ±0.1 % of Vout Ripple and Noise 5 Hz- 20 MHz BW, Vin=24V 40 70 mV pk-pk Temperature Coeffi cient At all outputs ±0.02 % of Vnom./°C Maximum Capacitive Loading Low ESR 1000 μF MECHANICAL Outline Dimensions 1 x 1 x 0.41 Inches (Please refer to outline drawing) WxLxH 25.4 x 25.4 x 10.41 mm Weight 0.69 Ounces 19.56 Grams Through Hole Pin Diameter 0.04 Inches 1.016 mm Through Hole Pin Material Copper alloy TH Pin Plating Metal and Thickness Nickel subplate 50 μ-inches Gold overplate 5 μ-inches ENVIRONMENTAL Operating Ambient Temperature Range See derating -40 85 °C Operating Case Temperature Range No derating -40 105 °C Case Material Tin plated steel with black powder coat Storage Temperature Vin = Zero (no power) -55 125 °C Thermal Protection/Shutdown Measured in center 110 115 120 °C Electromagnetic Interference External fi lter is required Conducted, EN55022/CISPR22 B Class RoHS rating RoHS-6 Notes ➀ Unless otherwise noted, all specifi cations are at nominal input voltage, nominal out- ➁ Input (back) ripple current is tested and specifi ed over 5 Hz to 20 MHz bandwidth. put voltage and full load. General conditions are +25˚ Celsius ambient temperature, Input fi ltering is Cbus=220 μF, Cin=33 μF and Lbus=12 μH. near sea level altitude, natural convection airfl ow. All models are tested and specifi ed ➂ The Remote On/Off Control is referred to -Vin. with external parallel 1 μF and 10 μF output capacitors. The external input capacitor is 100 μF, electrolytic. All capacitors are low-ESR types wired close to the converter. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 10 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-050-Q12 Effi ciency vs. Line Voltage and Load Current @ 25°C Power Dissipation 90 2.50 86 2.25 82 2.00 78 VIN = 36V 1.75 74 VIN = 30V VIN = 24V 1.50 70 VIN = 12V 66 1.25 VIN = 36V VIN = 9V 62 VIN = 30V 1.00 VIN = 24V 58 0.75 VIN = 12V 54 VIN = 9V 0.50 50 0.29 0.59 0.90 1.20 1.50 1.80 2.09 2.40 3.00 0.29 0.59 0.89 1.19 1.49 1.79 2.09 2.39 2.99 Output Load Current (Amps) Load Current (Amps) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 9V, 12V, or 24V (air fl ow from Pin J1 to Pin J3 on PCB) Vin 36 (air fl ow from Pin J1 to Pin J3 on PCB) 4 4 3 3 Natural Convection .5 m/s (100 LFM) Natural Convection 2 2 1 1 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr Paoperly and r ge 11 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om Output Current (Amps) Efficiency (%) Output Current (Amps) Power Dissipation (Watts) MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-050-Q12 Start-up Delay (Vin = 24V, Iout = 3A, Cload = 1μF || 10μF, Ta = +25°C) On/Off enable Delay (Vin = 24V, Iout = 3A, Cload = 1μF || 10μF, Ta = +25°C) CH1 = Vin, CH4 = Vout CH1 = Enable, CH4 = Vout Stepload Transient Response (Vin = 24V, Iout = 0.75 to 2.25A to 0.75A, Cload = 1μF || 10μF, Ta = +25°C) Ch1 = Iout, Ch4 = Vout Output Ripple and Noise (Vin = 24V, Iout = 0.30A, Cload = 1μF || 10μF, Output Ripple and Noise (Vin = 24V, Iout = 3A, Cload = 1μF || 10μF, Ta = +25°C, BW = 20Mhz) Ta = +25°C, BW = 20Mhz) www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 12 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS – MODEL SPM15-050-Q48 ABSOLUTE MAXIMUM RATINGS Conditions ➀ Minimum Typical/Nominal Maximum Units Input Voltage, Continuous 0 80 Vdc Input Voltage, Transient 100 mS max. duration 100 Vdc Isolation Voltage Input to output 1600 Vdc On/Off Remote Control Power on, referred to -Vin 0 15 Vdc Output Power 1.48 15.23 W Output Current Current-limited, no damage, short-circuit protected 0.3 3 A Storage Temperature Range Vin = Zero (no power) -55 125 ˚C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifi cations Table is not implied or recommended. INPUT Operating Voltage Range 18 48 75 Vdc Recommended External Fuse Fast blow 1.5 A Start-up Threshold Rising input voltage 16 16.9 17.9 Vdc Undervoltage Shutdown Falling input voltage 15 16 17.5 Vdc Internal Filter Type C Input Current Full Load Input Current Vin = nominal 0.35 0.37 A Low Line Input Current Vin = minimum 0.93 0.97 A 2 Inrush Transient 0.05 A -Sec. Short Circuit Input Current 0.05 0.1 mA Minimum Load Input Current Iout = minimum, unit=ON 56 90 mA Shut-Down Input Current (Off, UV, OT) 1 2 mA Refl ected (Back) Ripple Current ➁ Measured at input with specifi ed fi lter 30 mA, p-p GENERAL and SAFETY Vin = 48V, full load 86.5 88.5 % Effi ciency Vin = min., full load 87.5 89.5 % Isolation Isolation Voltage Input to output 1600 Vdc Isolation Resistance 10 MΩ Isolation Capacitance 1500 pF Certifi ed to UL-60950-1, CSA-C22.2 No. 60950- Safety Yes 1, IEC/60950-1, 2nd edition, with AM1 Per Telcordia SR332, issue 1, class 3, ground 6 Calculated MTBF 2 Hours x 10 fi xed, Tambient = +25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 320 345 375 KHz Startup Time Power on to Vout regulated 10 50 mS Startup Time Remote ON to Vout regulated 10 100 mS 50-75-50% load step, settling time to within Dynamic Load Response 60 120 μSec 1% of Vout Dynamic Load Peak Deviation same as above ±50 ±150 mV FEATURES and OPTIONS Remote On/Off Control ➂ “N” suffi x Negative Logic, ON state ON = Ground pin -0.7 0.8 V Negative Logic, OFF state OFF = Pin open 10 15 V Control Current Open collector/drain 1 mA “P” suffi x Positive Logic, ON state ON = Pin open 10 15 V Positive Logic, OFF state OFF = Ground pin -0.7 0.7 V Control Current Open collector/drain 1 mA www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 13 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) – MODEL SPM15-050-Q48 OUTPUT Conditions ➀ ➂ Minimum Typical/Nominal Maximum Units Total Output Power 1.48 15 15.23 W Voltage Nominal Output Voltage No trim 4.925 5 5.075 Vdc Setting Accuracy At 50% load, no trim -1.5 1.5 % of Vnom Output Voltage Range User-adjustable -10 10 % of Vnom. Overvoltage Protection Via magnetic feedback 6 7 8 Vdc Current Output Current Range 0.3 3 3 A Current Limit Inception 98% of Vnom., after warmup 3.75 4.5 5.5 A Short Circuit Hiccup technique, autorecovery within Short Circuit Current 0.3 A ±1.25% of Vout Short Circuit Duration (remove short for Output shorted to ground, no damage Continuous recovery) Short circuit protection method Current limiting Regulation Line Regulation Vin = min. to max., Vout = nom., Iout = nom. ±0.3 % of Vout Load Regulation Iout = min. to max., Vin = 48V ±0.2 % of Vout Ripple and Noise 5 Hz- 20 MHz BW, Vin=48V 60 95 mV pk-pk Maximum Capacitive Loading Low ESR 470 μF MECHANICAL Outline Dimensions 1 x 1 x 0.41 Inches (Please refer to outline drawing) WxLxH 25.4 x 25.4 x 10.41 mm Weight 0.69 Ounces 19.56 Grams Through Hole Pin Diameter 0.04 Inches 1.016 mm Through Hole Pin Material Copper alloy TH Pin Plating Metal and Thickness Nickel subplate 50 μ-inches Gold overplate 5 μ-inches ENVIRONMENTAL Operating Ambient Temperature Range See derating -40 85 °C Operating Case Temperature Range No derating -40 85 °C Case Material Tin plated steel with black powder coat Storage Temperature Vin = Zero (no power) -55 125 °C Thermal Protection/Shutdown Measured in center 130 135 150 °C Electromagnetic Interference External fi lter is required Conducted, EN55022/CISPR22 B Class RoHS rating RoHS-6 Notes ➀ Unless otherwise noted, all specifi cations are at nominal input voltage, nominal out- ➁ Input (back) ripple current is tested and specifi ed over 5 Hz to 20 MHz bandwidth. put voltage and full load. General conditions are +25˚ Celsius ambient temperature, Input fi ltering is Cbus=220 μF, Cin=33 μF and Lbus=12 μH. near sea level altitude, natural convection airfl ow. All models are tested and specifi ed ➂ The Remote On/Off Control is referred to -Vin. with external parallel 1 μF and 10 μF output capacitors. The external input capacitor is 100 μF, electrolytic. All capacitors are low-ESR types wired close to the converter. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 14 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-050-Q48 Effi ciency vs. Line Voltage and Load Current @ 25°C Power Dissipation 90 3.0 85 2.5 80 VIN = 75V 75 2.0 VIN = 48V 70 VIN = 36V VIN = 24V 65 1.5 VIN = 75V VIN = 18V 60 VIN = 48V VIN = 36V 55 1.0 VIN = 24V 50 VIN = 18V 0.5 45 0.35 0.68 1.02 1.35 1.69 2.02 2.35 2.68 3.02 0.35 0.68 1.02 1.35 1.69 2.02 2.35 2.68 3.02 Output Load Current (Amps) Load Current (Amps) Maximum Current Temperature Derating at sea level Vin = 18V, 24V, 36V, or 48V (air fl ow from Pin 1 to Pin 2 on PCB) 4 3 0.5 m/s (100 LFM); 1.0 m/s (200 LFM); 1.5 m/s (300 LFM); 2.0 m/s (400 LFM); Natural Convection 2 1 0 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin 60 (air fl ow from Pin 1 to Pin 2 on PCB) Vin 75 (air fl ow from Pin 1 to Pin 2 on PCB) 4 4 3 3 0.5 m/s (100 LFM); 1.0 m/s (200 LFM); 0.5 m/s (100 LFM); 1.0 m/s (200 LFM); 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) Natural Convection Natural Convection 2 2 1 1 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr Paoperly and r ge 15 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om Output Current (Amps) Efficiency (%) Output Current (Amps) Output Current (Amps) Power Dissipation (Watts) MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS – MODEL SPM15-120-Q12 ABSOLUTE MAXIMUM RATINGS Conditions ➀ Minimum Typical/Nominal Maximum Units Input Voltage, Continuous 0 36 Vdc Input Voltage, Transient 100 mS max. duration 50 Vdc Isolation Voltage Input to output 1600 Vdc On/Off Remote Control Power on, referred to -Vin 0 15 Vdc Output Power 1.54 15.76 W Output Current Current-limited, no damage, short-circuit protected 0.13 1.3 A Storage Temperature Range Vin = Zero (no power) -55 125 ˚C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifi cations Table is not implied or recommended. INPUT Operating Voltage Range 9 24 36 Vdc Recommended External Fuse Fast blow 4 A Start-up Threshold Rising input voltage 8 8.5 9 Vdc Undervoltage Shutdown Falling input voltage 7.9 8.2 8.7 Vdc Internal Filter Type C Input Current Full Load Input Current Vin = nominal 0.77 0.8 A Low Line Input Current Vin = minimum 2.05 2.11 A 2 Inrush Transient 0.05 A -Sec. Short Circuit Input Current 50 120 mA Minimum Load Input Current Iout = minimum, unit=ON 105 130 mA Shut-Down Input Current (Off, UV, OT) 1 2.5 mA Refl ected (Back) Ripple Current ➁ Measured at input with specifi ed fi lter 30 mA, p-p GENERAL and SAFETY Vin = 24V, full load 82.5 84 % Effi ciency Vin = min., full load 83 84.5 % Isolation Isolation Voltage Input to output 1600 Vdc Isolation Resistance 10 MΩ Isolation Capacitance 1500 pF Certifi ed to UL-60950-1, CSA-C22.2 No. 60950- Safety Yes 1, IEC/60950-1, 2nd edition, with AM1 Per Telcordia SR332, issue 1, class 3, ground 6 Calculated MTBF TBD Hours x 10 fi xed, Tambient = +25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 300 330 360 KHz Startup Time Power on to Vout regulated 5 50 mS Startup Time Remote ON to Vout regulated 5 50 mS 50-75-50% load step, settling time to within Dynamic Load Response 60 120 μSec 1% of Vout Dynamic Load Peak Deviation same as above ±100 ±150 mV FEATURES and OPTIONS Remote On/Off Control ➂ “N” suffi x Negative Logic, ON state ON = Ground pin -0.7 0.8 V Negative Logic, OFF state OFF = Pin open 10 15 V Control Current Open collector/drain 1 mA “P” suffi x Positive Logic, ON state ON = Pin open 10 15 V Positive Logic, OFF state OFF = Ground pin -0.7 0.7 V Control Current Open collector/drain 1 mA www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 16 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) – MODEL SPM15-120-Q12 OUTPUT Conditions ➀ ➂ Minimum Typical/Nominal Maximum Units Total Output Power 1.54 15.6 15.76 W Voltage Nominal Output Voltage No trim 11.88 12 12.12 Vdc Setting Accuracy At 50% load, no trim -1 1 % of Vnom Output Voltage Range User-adjustable -10 10 % of Vnom. Overvoltage Protection Via magnetic feedback 15.5 17.2 19.5 Vdc Current Output Current Range 0.13 1.3 1.3 A Current Limit Inception 98% of Vnom., after warmup 1.5 2.1 2.6 A Short Circuit Hiccup technique, autorecovery within Short Circuit Current 0.3 A ±1.25% of Vout Short Circuit Duration (remove short for Output shorted to ground, no damage Continuous recovery) Short circuit protection method Current limiting Regulation Line Regulation Vin = min. to max., Vout = nom., Iout = nom. ±0.05 % of Vout Load Regulation Iout = min. to max., Vin = 24V ±0.1 % of Vout Ripple and Noise 5 Hz- 20 MHz BW, Vin=24V 60 120 mV pk-pk Temperature Coeffi cient At all outputs ±0.02 % of Vnom./°C Maximum Capacitive Loading Low ESR 470 μF MECHANICAL Outline Dimensions 1 x 1 x 0.41 Inches (Please refer to outline drawing) WxLxH 25.4 x 25.4 x 10.41 mm Weight 0.69 Ounces 19.56 Grams Through Hole Pin Diameter 0.04 Inches 1.016 mm Through Hole Pin Material Copper alloy TH Pin Plating Metal and Thickness Nickel subplate 50 μ-inches Gold overplate 5 μ-inches ENVIRONMENTAL Operating Ambient Temperature Range See derating -40 85 °C Operating Case Temperature Range No derating -40 105 °C Case Material Tin plated steel with black powder coat Storage Temperature Vin = Zero (no power) -55 125 °C Thermal Protection/Shutdown Measured in center 110 115 120 °C Electromagnetic Interference External fi lter is required Conducted, EN55022/CISPR22 B Class RoHS rating RoHS-6 Notes ➀ Unless otherwise noted, all specifi cations are at nominal input voltage, nominal out- ➁ Input (back) ripple current is tested and specifi ed over 5 Hz to 20 MHz bandwidth. put voltage and full load. General conditions are +25˚ Celsius ambient temperature, Input fi ltering is Cbus=220 μF, Cin=33 μF and Lbus=12 μH. near sea level altitude, natural convection airfl ow. All models are tested and specifi ed ➂ The Remote On/Off Control is referred to -Vin. with external parallel 1 μF and 10 μF output capacitors. The external input capacitor is 100 μF, electrolytic. All capacitors are low-ESR types wired close to the converter. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 17 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-120-Q12 Effi ciency vs. Line Voltage and Load Current @ 25°C 88 86 84 82 80 78 VIN = 9V VIN = 12V 76 VIN = 24V 74 VIN = 36V 72 70 0.13 0.26 0.39 0.52 0.65 0.78 0.91 1.04 1.17 1.30 Load Current (Amps) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 9V (air fl ow from Pin 1 to Pin 2 on PCB) Vin = 12V (air fl ow from Pin 1 to Pin 2 on PCB) 2 2 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 1 1 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) 1.5 m/s (300 LFM); 2.0 m/s (400 LFM); Natural Convection Natural Convection 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 24V (air fl ow from Pin 1 to Pin 2 on PCB) Vin = 36V (air fl ow from Pin 1 to Pin 2 on PCB) 2 2 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 1 1 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) Natural Convection Natural Convection 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr Paoperly and r ge 18 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om Output Current (Amps) Output Current (Amps) Efficiency (%) Output Current (Amps) Output Current (Amps) MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-120-Q12 Output Ripple and Noise (Vin = 24V, Iout = 1.3A, Cload = 1μf || 10μF, Output Ripple and Noise (Vin = 24V, Iout = 0.13A, Cload = 1μf || 10μF, Ta = +25°C, BW = 20Mhz) Ta = +25°C, BW = 20Mhz) Start-up Delay (Vin = 24V, Iout = 1.3A, Cload = 470μF, Ta = +25°C) On/Off enable Delay (Vin = 24V, Iout = 1.3A, Cload = 470μF, Ta = +25°C) CH1 = Vout, CH3 = Vin. CH1 = enable, CH2 = Vout. Stepload Transient Response (Vin = 24V, Iout = 50-75-50% of Imax, Stepload Transient Response (Vin = 24V, Iout = 50-75-50% of Imax, Cload = 1μf || 10μF, Io = 200mA/div, Ta = +25°C) CH2 = Vout, CH4 = Iout) Cload = 470μF, Io = 200mA/div, Ta = +25°C) CH2 = Vout, CH4 = Iout) www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 19 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS – MODEL SPM15-120-Q48 ABSOLUTE MAXIMUM RATINGS Conditions ➀ Minimum Typical/Nominal Maximum Units Input Voltage, Continuous 0 80 Vdc Input Voltage, Transient 100 mS max. duration 100 Vdc Isolation Voltage Input to output 1600 Vdc On/Off Remote Control Power on, referred to -Vin 0 15 Vdc Output Power 1.54 15.76 W Output Current Current-limited, no damage, short-circuit protected 0.13 1.3 A Storage Temperature Range Vin = Zero (no power) -55 125 ˚C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifi cations Table is not implied or recommended. INPUT Operating voltage range 18 48 75 Vdc Recommended External Fuse Fast blow 1.5 A Start-up threshold Rising input voltage 16 16.75 17.5 Vdc Undervoltage shutdown Falling input voltage 15 16 17 Vdc Turn-On/Turn-Off Hysteresis 1.5 Vdc Internal Filter Type LC Input current Full Load Input Current Vin = 24V 0.76 0.782 A Full Load Input Current Vin = 48V 0.387 0.400 A Low Line Input Current Vin = minimum 1.032 1.042 2 Inrush Transient 0.05 A -Sec. Short Circuit Input Current 50 100 mA Minimum Load Input Current Iout = minimum, unit = ON 56 90 mA Shut-Down Input Current (Off, UV, OT) 1 2 mA Measured at input with specifi ed fi lter 30 mA, p-p Refl ected (back) ripple current ➁ GENERAL and SAFETY Vin = 48V, full load 82 85.5 % Effi ciency Vin = 24V., full load 84 84 % Isolation Isolation Voltage Input to output 1600 Vdc Isolation Resistance 10 MΩ Isolation Capacitance 1500 pF Certifi ed to UL-60950-1, CSA-C22.2 No. 60950- Safety Yes 1, IEC/60950-1, 2nd edition, with AM1 Per Telcordia SR332, issue 1, class 3, ground 6 Calculated MTBF 6.4 Hours x 10 fi xed, Tambient = +25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 300 335 370 KHz Startup Time Power on to Vout regulated 10 50 mS Startup Time Remote ON to Vout regulated 10 50 mS 50-75-50% load step, settling time to within Dynamic Load Response 50 100 μSec 1% of Vout Dynamic Load Peak Deviation same as above ±125 ±200 mV FEATURES and OPTIONS Remote On/Off Control ➂ “N” suffi x Negative Logic, ON state ON = Ground pin -0.7 0.8 V Negative Logic, OFF state OFF = Pin open 10 15 V Control Current Open collector/drain 1 mA “P” suffi x Positive Logic, ON state ON = Pin open 10 15 V Positive Logic, OFF state OFF = Ground pin -0.7 0.7 V Control Current Open collector/drain 1 mA www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 20 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) – MODEL SPM15-120-Q48 OUTPUT Conditions ➀ ➂ Minimum Typical/Nominal Maximum Units Total Output Power 1.54 15.6 15.76 W Voltage Nominal Output Voltage No trim 11.88 12 12.12 Vdc Setting Accuracy At 50% load, no trim -1 1 % of Vnom Output Voltage Range User-adjustable -10 10 % of Vnom. Overvoltage Protection Via magnetic feedback 14.5 16.5 17.5 Vdc Current Output Current Range 0.13 1.3 1.3 A Current Limit Inception 98% of Vnom., after warmup 1.5 1.9 2.3 A Short Circuit Hiccup technique, autorecovery within Short Circuit Current TBD A ±1.25% of Vout Short Circuit Duration (remove short for Output shorted to ground, no damage Continuous recovery) Short circuit protection method Current limiting Regulation Line Regulation Vin = min. to max., Vout = nom., Iout = nom. ±0.075 % of Vout Load Regulation Iout = min. to max., Vin = 48V ±0.05 % of Vout Ripple and Noise 5 Hz- 20 MHz BW, Vin=48V 85 120 mV pk-pk Temperature Coeffi cient At all outputs ±0.02 % of Vnom./°C Maximum Capacitive Loading Low ESR 470 μF MECHANICAL Outline Dimensions 1 x 1 x 0.41 Inches (Please refer to outline drawing) WxLxH 25.4 x 25.4 x 10.41 mm Weight 0.69 Ounces 19.56 Grams Through Hole Pin Diameter 0.04 Inches 1.016 mm Through Hole Pin Material Copper alloy TH Pin Plating Metal and Thickness Nickel subplate 50 μ-inches Gold overplate 5 μ-inches ENVIRONMENTAL Operating Ambient Temperature Range See Derating -40 85 °C Operating Case Temperature Range No derating -40 105 °C Case Material Tin plated steel with black powder coat Storage Temperature Vin = Zero (no power) -55 125 °C Thermal Protection/Shutdown Measured in center 130 135 150 °C Electromagnetic Interference External fi lter is required Conducted, EN55022/CISPR22 B Class RoHS rating RoHS-6 Notes ➀ Unless otherwise noted, all specifi cations are at nominal input voltage, nominal out- ➁ Input (back) ripple current is tested and specifi ed over 5 Hz to 20 MHz bandwidth. put voltage and full load. General conditions are +25˚ Celsius ambient temperature, Input fi ltering is Cbus=220 μF, Cin=33 μF and Lbus=12 μH. near sea level altitude, natural convection airfl ow. All models are tested and specifi ed ➂ The Remote On/Off Control is referred to -Vin. with external parallel 1 μF and 10 μF output capacitors. The external input capacitor is 4.7 μF. All capacitors are low-ESR types wired close to the converter. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 21 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-120-Q48 Effi ciency vs. Line Voltage and Load Current @ 25°C 2 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 1 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) Natural Convection 0 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 18V (air fl ow from Pin 1 to Pin 2 on PCB) Vin = 24V (air fl ow from Pin 1 to Pin 2 on PCB) 2 2 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 1 1 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) Natural Convection Natural Convection 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 48V (air fl ow from Pin 1 to Pin 2 on PCB) Vin = 75V (air fl ow from Pin 1 to Pin 2 on PCB) 2 2 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 0.33 m/s (65 LFM); 1.0 m/s (200 LFM); 1 1 1.5 m/s (300 LFM); 2.0 m/s (400 LFM); 1.5 m/s (300 LFM); 2.0 m/s (400 LFM) Natural Convection Natural Convection 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr Paoperly and r ge 22 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om Output Current (Amps) Output Current (Amps) Output Current (Amps) Output Current (Amps) Output Current (Amps) MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS – MODEL SPM15-150-Q12 ABSOLUTE MAXIMUM RATINGS Conditions ➀ Minimum Typical/Nominal Maximum Units Input Voltage, Continuous 0 36 Vdc Input Voltage, Transient 100 mS max. duration 50 Vdc Isolation Voltage Input to output 1600 Vdc On/Off Remote Control Power on, referred to -Vin 0 15 Vdc Output Power 1.63 16.67 W Output Current Current-limited, no damage, short-circuit protected 0.11 1.1 A Storage Temperature Range Vin = Zero (no power) -55 125 ˚C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifi cations Table is not implied or recommended. INPUT Operating voltage range 9 24 36 Vdc Recommended External Fuse Fast blow 4 A Start-up threshold (@+25°C and -40°C) Rising input voltage 8 8.5 9 Vdc Undervoltage shutdown Falling input voltage 7.8 8.25 9 Vdc Internal Filter Type C Input current Full Load Input Current Vin = nominal 0.82 0.84 A Low Line Input Current Vin = minimum 2.13 2.19 A 2 Inrush Transient 0.05 A -Sec. Short Circuit Input Current 50 100 mA Minimum Load Input Current Iout = minimum, unit = ON 130 150 mA Shut-Down Input Current (Off, UV, OT) 1 2.5 mA Measured at input with specifi ed fi lter 30 mA, p-p Refl ected (back) ripple current ➁ GENERAL and SAFETY Vin = 24V, full load 82.5 84 % Effi ciency Vin = min., full load 84.5 86 % Isolation Isolation Voltage Input to output 1600 Vdc Insulation Safety Rating basic Isolation Resistance 10 MΩ Isolation Capacitance 1500 pF Certifi ed to UL-60950-1, CSA-C22.2 No. 60950- Safety Yes 1, IEC/60950-1, 2nd edition, with AM1 Per Telcordia SR332, issue 1, class 3, ground 6 Calculated MTBF TBD Hours x 10 fi xed, Tambient = +25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 300 330 360 KHz Startup Time Power on to Vout regulated 50 mS Startup Time Remote on to Vout regulated 50 mS 50-75-50% load step, settling time to within Dynamic Load Response 100 150 μSec 1% of Vout Dynamic Load Peak Deviation same as above ±150 ±250 mV FEATURES and OPTIONS Remote On/Off Control ➂ “N” suffi x Negative Logic, ON state ON = Ground pin -0.7 0.8 V Negative Logic, OFF state OFF = Pin open 10 15 V Control Current Open collector/drain 1 mA “P” suffi x Positive Logic, ON state ON = Pin open 10 15 V Positive Logic, OFF state OFF = Ground pin -0.7 0.7 V Control Current Open collector/drain 1 mA www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 23 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) – MODEL SPM15-150-Q12 OUTPUT Conditions ➀ ➂ Minimum Typical/Nominal Maximum Units Total Output Power 1.63 16.5 16.67 W Voltage Nominal Output Voltage No trim 14.85 15 15.15 Vdc Setting Accuracy At 50% load, no trim 1 1 % of Vnom Output Voltage Range User-adjustable -10 10 % of Vnom. Overvoltage Protection Via magnetic feedback 17 19.5 22.5 Vdc Current Output Current Range 0.11 1.1 1.1 A Current Limit Inception 98% of Vnom., after warmup 1.2 1.6 2 A Short Circuit Hiccup technique, autorecovery within Short Circuit Current 0.3 A ±1.25% of Vout Short Circuit Duration (remove short for Output shorted to ground, no damage Continuous recovery) Short circuit protection method Current limiting Regulation Line Regulation Vin = min. to max., Vout = nom., Iout = nom. ±0.1 % of Vout Load Regulation Iout = min. to max., Vin = 24V ±0.1 % of Vout Ripple and Noise 5 Hz- 20 MHz BW, Vin=24V 130 175 mV pk-pk Temperature Coeffi cient At all outputs ±0.02 % of Vnom./°C Maximum Capacitive Loading Low ESR 470 μF MECHANICAL Outline Dimensions 1 x 1 x 0.41 Inches (Please refer to outline drawing) WxLxH 25.4 x 25.4 x 10.41 mm Weight 0.69 Ounces 19.56 Grams Through Hole Pin Diameter 0.04 Inches 1.016 mm Through Hole Pin Material Copper alloy TH Pin Plating Metal and Thickness Nickel subplate 50 μ-inches Gold overplate 5 μ-inches ENVIRONMENTAL Operating Ambient Temperature Range See Derating -40 85 °C Operating Case Temperature Range No derating -40 105 °C Case Material Tin plated steel with black powder coat Storage Temperature Vin = Zero (no power) -55 125 °C Thermal Protection/Shutdown Measured in center 110 115 120 °C Electromagnetic Interference External fi lter is required Conducted, EN55022/CISPR22 B Class RoHS rating RoHS-6 Notes ➀ Unless otherwise noted, all specifi cations are at nominal input voltage, nominal out- ➁ Input (back) ripple current is tested and specifi ed over 5 Hz to 20 MHz bandwidth. put voltage and full load. General conditions are +25˚ Celsius ambient temperature, Input fi ltering is Cbus=220 μF, Cin=33 μF and Lbus=12 μH. near sea level altitude, natural convection airfl ow. All models are tested and specifi ed ➂ The Remote On/Off Control is referred to -Vin. with external parallel 1 μF and 10 μF output capacitors. The external input capacitor is 100 μF, electrolytic. All capacitors are low-ESR types wired close to the converter. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 24 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-150-Q12 Effi ciency vs. Line Voltage and Load Current @ 25°C 90 85 80 75 VIN = 9V VIN = 12V 70 VIN = 24V VIN = 36V 65 60 0.11 0.22 0.33 0.44 0.55 0.66 0.77 0.88 0.99 1.1 Load Current (Amps) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 9, 12, or 24V (unit monuted on PCB)* Vin = 36V (air fl ow is from J1 to J3 on PCB* 2 2 1 1 Natural Convection 0.33 m/s (65 LFM) Natural Convection 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) *Using Burn in board, connection with solder www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr Paoperly and r ge 25 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om Output Current (Amps) Efficiency (%) Output Current (Amps) MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-150-Q12 Output Ripple and Noise(Vin = 24V, Iout = 0.11A, Cload = 1μF || 10μF, Output Ripple and Noise(Vin = 24V, Iout = 1.1A, Cload = 1μF || 10μF, Ta = +25°C, BW = 20Mhz) Ta = +25°C, BW = 20Mhz) Start-up Delay (Vin = 24V, Iout = 1.1A, Cload = 1μF || 10μF, On/Off enable Delay (Vin = 24V, Iout = 1.1A, Cload = 1μF || 10μF, Ta = +25°C) CH1 = Vout, CH3 = Vin Ta = +25°C) CH1 = Vout, CH3 = Enable Stepload Transient Response (Vin = 24V, Iout = 50% to 75%, Cload = 1μF || 10μF, Ta = +25°C) Ch1 = Vout, Ch4 = Iout www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 26 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS – MODEL SPM15-150-Q48 ABSOLUTE MAXIMUM RATINGS Conditions ➀ Minimum Typical/Nominal Maximum Units Input Voltage, Continuous 0 80 Vdc Input Voltage, Transient 100 mS max. duration 100 Vdc Isolation Voltage Input to output 1600 Vdc On/Off Remote Control Power on, referred to -Vin 0 15 Vdc Output Power 1.63 16.67 W Output Current Current-limited, no damage, short-circuit protected 0.11 1.1 A Storage Temperature Range Vin = Zero (no power) -55 125 ˚C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifi cations Table is not implied or recommended. INPUT Operating voltage range 18 48 75 Vdc Recommended External Fuse Fast blow 2 A Start-up threshold Rising input voltage 16 16.7 17.9 Vdc Undervoltage shutdown Falling input voltage 15 16.2 17.5 Vdc Internal Filter Type C Input current Full Load Input Current Vin = nominal 0.41 0.42 A Low Line Input Current Vin = minimum 1.06 1.09 A 2 Inrush Transient 0.05 A -Sec. Short Circuit Input Current 50 100 mA Minimum Load Input Current Iout = minimum, unit = ON 60 85 mA Shut-Down Input Current (Off, UV, OT) 1 2 mA Refl ected (back) ripple current ➁ Measured at input with specifi ed fi lter 30 mA, p-p GENERAL and SAFETY Vin = 48V, full load 83 85.5 % Effi ciency Vin = min., full load 85 86.5 % Isolation Isolation Voltage Input to output 1600 Vdc Insulation Safety Rating basic Isolation Resistance 10 MΩ Isolation Capacitance 1500 pF Certifi ed to UL-60950-1, CSA-C22.2 No. 60950- Safety Yes 1, IEC/60950-1, 2nd edition, with AM1 Per Telcordia SR332, issue 1, class 3, ground 6 Calculated MTBF TBD Hours x 10 fi xed, Tambient = +25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 300 330 360 KHz Startup Time Power on to Vout regulated 50 mS Startup Time Remote on to Vout regulated 50 mS 50-75-50% load step, settling time to within Dynamic Load Response 60 120 μSec 1% of Vout Dynamic Load Peak Deviation same as above ±150 ±250 mV FEATURES and OPTIONS Remote On/Off Control ➂ “N” suffi x Negative Logic, ON state ON = Ground pin -0.7 0.8 V Negative Logic, OFF state OFF = Pin open 10 15 V Control Current Open collector/drain 1 mA “P” suffi x Positive Logic, ON state ON = Pin open 10 15 V Positive Logic, OFF state OFF = Ground pin -0.7 0.7 V Control Current Open collector/drain 1 mA www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 27 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) – MODEL SPM15-150-Q48 OUTPUT Conditions ➀ ➂ Minimum Typical/Nominal Maximum Units Total Output Power 1.63 16.5 16.67 W Voltage Nominal Output Voltage No trim 14.85 15 15.15 Vdc Setting Accuracy At 50% load, no trim 1 1 % of Vnom Output Voltage Range User-adjustable -10 10 % of Vnom. Overvoltage Protection Via magnetic feedback 19 20 21.5 Vdc Current Output Current Range 0.11 1.1 1.1 A Current Limit Inception 98% of Vnom., after warmup 1.3 1.7 2.2 A Short Circuit Hiccup technique, autorecovery within Short Circuit Current 0.3 A ±1.25% of Vout Short Circuit Duration (remove short for Output shorted to ground, no damage Continuous recovery) Short circuit protection method Current limiting Regulation Line Regulation Vin = min. to max., Vout = nom., Iout = nom. ±0.1 % of Vout Load Regulation Iout = min. to max., Vin = 48V ±0.075 % of Vout Ripple and Noise 5 Hz- 20 MHz BW, Vin=24V 80 150 mV pk-pk Temperature Coeffi cient At all outputs ±0.02 % of Vnom./°C Maximum Capacitive Loading Low ESR 470 μF MECHANICAL Outline Dimensions 1 x 1 x 0.41 Inches (Please refer to outline drawing) WxLxH 25.4 x 25.4 x 10.41 mm Weight 0.69 Ounces 19.56 Grams Through Hole Pin Diameter 0.04 Inches 1.016 mm Through Hole Pin Material Copper alloy TH Pin Plating Metal and Thickness Nickel subplate 50 μ-inches Gold overplate 5 μ-inches ENVIRONMENTAL Operating Ambient Temperature Range See Derating -40 85 °C Operating Case Temperature Range No derating -40 105 °C Case Material Tin plated steel with black powder coat Storage Temperature Vin = Zero (no power) -55 125 °C Thermal Protection/Shutdown Measured in center 110 115 120 °C Electromagnetic Interference External fi lter is required Conducted, EN55022/CISPR22 B Class RoHS rating RoHS-6 Notes ➀ Unless otherwise noted, all specifi cations are at nominal input voltage, nominal out- ➁ Input (back) ripple current is tested and specifi ed over 5 Hz to 20 MHz bandwidth. put voltage and full load. General conditions are +25˚ Celsius ambient temperature, Input fi ltering is Cbus=220 μF, Cin=33 μF and Lbus=12 μH. near sea level altitude, natural convection airfl ow. All models are tested and specifi ed ➂ The Remote On/Off Control is referred to -Vin. with external parallel 1 μF and 10 μF output capacitors. The external input capacitor is 4.7 μF. All capacitors are low-ESR types wired close to the converter. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 28 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-150-Q48 Effi ciency vs. Line Voltage and Load Current @ 25°C 90 85 80 75 VIN = 9V 70 VIN = 12V VIN = 24V 65 VIN = 36V 60 0.11 0.22 0.33 0.44 0.55 0.66 0.77 0.88 0.99 1.1 Load Current (Amps) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 18, 24, or 36V (air fl ow from J 1 to J3 on PCB)* Vin = 48V (air fl ow from J 1 to J3 on PCB)* 2 2 1 1 Natural Convection 0.33 m/s (65 LFM) Natural Convection 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) Maximum Current Temperature Derating at sea level Maximum Current Temperature Derating at sea level Vin = 60V (air fl ow from J 1 to J3 on PCB)* Vin = 75V (air fl ow from J 1 to J3 on PCB)* 2 2 1 1 0.33 m/s (65 LFM) 0.33 m/s (65 LFM) Natural Convection Natural Convection 0 0 30 35 40 45 50 55 60 65 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (°C) Ambient Temperature (°C) *Using Burn in board, connection with solder www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr Paoperly and r ge 29 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om Output Current (Amps) Output Current (Amps) Efficiency (%) Output Current (Amps) Output Current (Amps) MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters TYPICAL PERFORMANCE DATA, SPM15-150-Q48 Output Ripple and Noise(Vin = 48V, Iout = 0.11A, Cload = 1μF || 10μF, Output Ripple and Noise(Vin = 48V, Iout = 1.1A, Cload = 1μF || 10μF, Ta = +25°C, BW = 20Mhz) Ta = +25°C, BW = 20Mhz) Start-up Delay (Vin = 48V, Iout = 1.1A, Cload = 1μF || 10μF, On/Off enable Delay (Vin = 48V, Iout = 1.1A, Cload = 1μF || 10μF, Ta = +25°C) CH1 = Vout, CH3 = Vin Ta = +25°C) CH1 = Vout, CH3 = Enable Stepload Transient Response (Vin = 48V, Iout = 50% to 75%, Cload = 1μF || 10μF, Ta = +25°C) Ch1 = Vout, Ch4 = Iout www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 30 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters MECHANICAL SPECIFICATIONS BOTTOM VIEW SIDE VIEW 0.800 0.41 (20.32) (10.41) 3 1 0.800 4 1.00 (25.4) 2 C L 0.500 (20.32) 0.400 0.300 (12.7) (10.16) (7.62) 6 5 0.400 (10.16) 0.02 (0.508) REF C L 0.15 4x 0.060-0.100 (3.81) x 0.015-0.025 HIGH NON-METALLIC STANDOFFS (DIMPLES) INSULATING HEADER END VIEW PIN #1 ISOMETRIC VIEW 6 5 (FOR REF ONLY) 2 4 PIN #1 1 INPUT/OUTPUT CONNECTIONS INDICATOR SPM Function Pin 3 (Single Output) Dimensions are in inches (mm shown for ref. only). 1 +Vin TOP VIEW 2 -Vin Third Angle Projection 3 +Vout MATERIAL: 4 Output Trim* .040 PINS: COPPER ALLOY 5 -Vout 6 On/Off Control* FINISH: (ALL PINS) * The Output Trim and On/Off Control GOLD (5μ"MIN) OVER NICKEL (50μ" MIN) Tolerances (unless otherwise specified): pins are optional. Also, the Remote .XX ± 0.02 (0.5) On/Off can be provided with either .XXX ± 0.010 (0.25) positive (P suffi x) or negative Angles ± 2˚ (N suffi x) logic. Please see the Part Number Structure on Page 2. Components are shown for reference only. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensur MDC_SPM15.C02 e a product will work pr Paoperly and r ge 31 of 36 eliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters RECOMMENDED FOOTPRINT (VIEW THROUGH CONVERTER) TOP VIEW 0.800 (20.32) 0.400 (10.16) 65 0.100 1.02 (25.91) MIN 0.400 0.275 COURTYARD (10.16) (6.99) 2 4 0.55 0.800 C C L L (13.97) (20.32) 1 0.51 (12.95) 0.100 3 0.51 4x 0.100 'LANDING (12.95) FINISHED HOLE SIZES C L ZONES' FOR NON-METALLIC @ PINS 1 THRU 6 STANDOFFS (PER IPC-D-275, LEVEL C) 1.02 (25.91) MIN (KEEP FREE OF COMPS) 0.048-0.062 COURTYARD STANDARD PACKAGING EACH STATIC DISSIPATIVE PLASTIC TUBE HOLDS 16 CONVERTERS 21.88 0.91 (23.11) REF (555.75) REF 16 UNITS PER TUBE 6 TUBES PER CARTON 1.16 (29.46) REF www.murata-ps.com/support MDC_SPM15.C02 Page 32 of 36 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters Because of the switching nature of DC/DC converters, the input of these TECHNICAL NOTES converters must be driven from a source with both low AC impedance and Input Fusing adequate DC input regulation. Performance will degrade with increasing input Certain applications and/or safety agencies may require fuses at the inputs of inductance. Excessive input inductance may inhibit operation. The DC input power conversion components. Fuses should also be used when there is the regulation specifi es that the input voltage, once operating, must never degrade possibility of sustained input voltage reversal which is not current-limited. For below the Shut-Down Threshold under all load conditions. Be sure to use greatest safety, we recommend a fast blow fuse installed in the ungrounded adequate trace sizes and mount components close to the converter. input supply line. I/O Filtering, Input Ripple Current and Output Noise The installer must observe all relevant safety standards and regulations. For All models in this converter series are tested and specifi ed for input refl ected safety agency approvals, install the converter in compliance with the end-user ripple current and output noise using designated external input/output compo- safety standard. nents, circuits and layout as shown in the fi gures below. External input capaci- Input Under-Voltage Shutdown and Start-Up Threshold tors (CIN in the fi gure) serve primarily as energy storage elements, minimizing line voltage variations caused by transient IR drops in the input conductors. Under normal start-up conditions, converters will not begin to regulate properly Users should select input capacitors for bulk capacitance (at appropriate until the rising input voltage exceeds and remains at the Start-Up Threshold frequencies), low ESR and high RMS ripple current ratings. In the fi gure below, Voltage (see Specifi cations). Once operating, converters will not turn off until the CBUS and LBUS components simulate a typical DC voltage bus. Your specifi c the input voltage drops below the Under-Voltage Shutdown Limit. Subsequent system confi guration may require additional considerations. Please note that the restart will not occur until the input voltage rises again above the Start-Up values of CIN, LBUS and CBUS may vary according to the specifi c converter model. Threshold. This built-in hysteresis prevents any unstable on/off operation at a single input voltage. TO Users should be aware however of input sources near the Under-Voltage CURRENT OSCILLOSCOPE PROBE Shutdown whose voltage decays as input current is consumed (such as capacitor 1 +VIN inputs), the converter shuts off and then restarts as the external capacitor re- LBUS + charges. Such situations could oscillate. To prevent this, make sure the operating – VIN input voltage is well above the UV Shutdown voltage AT ALL TIMES. CBUS CIN + – Start-Up Delay 2 −VIN Assuming that the output current is set at the rated maximum, the Vin to Vout Start- Up Delay (see Specifi cations) is the time interval between the point when the rising CIN = 33μF, ESR < 700mΩ @ 100kHz CBUS = 220μF, ESR < 100mΩ @ 100kHz input voltage crosses the Start-Up Threshold and the fully loaded regulated output LBUS = 12μH voltage enters and remains within its specifi ed regulation band. Actual measured times will vary with input source impedance, external input capacitance, input volt- Figure 1. Measuring Input Ripple Current age slew rate and fi nal value of the input voltage as it appears at the converter. In critical applications, output ripple and noise (also referred to as periodic These converters include a soft start circuit to moderate the duty cycle of the and random deviations or PARD) may be reduced by adding fi lter elements PWM controller at power up, thereby limiting the input inrush current. such as multiple external capacitors. Be sure to calculate component tempera- The On/Off Remote Control interval from inception to VOUT regulated as- ture rise from refl ected AC current dissipated inside capacitor ESR. sumes that the converter already has its input voltage stabilized above the Floating Outputs Start-Up Threshold before the On command. The interval is measured from the Since these are isolated DC/DC converters, their outputs are “fl oating” with On command until the output enters and remains within its specifi ed regulation respect to their input. The essential feature of such isolation is ideal ZERO band. The specifi cation assumes that the output is fully loaded at maximum CURRENT FLOW between input and output. Real-world converters however do rated current. exhibit tiny leakage currents between input and output (see Specifi cations). Input Source Impedance These leakages consist of both an AC stray capacitance coupling component These converters will operate to specifi cations without external components, and a DC leakage resistance. When using the isolation feature, do not allow assuming that the source voltage has very low impedance and reasonable in- the isolation voltage to exceed specifi cations. Otherwise the converter may put voltage regulation. Since real-world voltage sources have fi nite impedance, be damaged. Designers will normally use the negative output (-Output) as performance is improved by adding external fi lter components. Sometimes only the ground return of the load circuit. You can however use the positive output a small ceramic capacitor is suffi cient. Since it is diffi cult to totally characterize (+Output) as the ground return to effectively reverse the output polarity. all applications, some experimentation may be needed. Note that external input capacitors must accept high speed switching currents. www.murata-ps.com/support MDC_SPM15.C02 Page 33 of 36 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters Output Overvoltage Protection (OVP) This converter monitors its output voltage for an over-voltage condition using an on-board electronic comparator. The signal is optically coupled to the pri- +VOUT mary side PWM controller. If the output exceeds OVP limits, the sensing circuit will power down the unit, and the output voltage will decrease. After a time-out RLOAD C1 SCOPE C2 period, the PWM will automatically attempt to restart, causing the output volt- age to ramp up to its rated value. It is not necessary to power down and reset −VOUT the converter for this automatic OVP-recovery restart. If the fault condition persists and the output voltage climbs to excessive levels, the OVP circuitry will initiate another shutdown cycle. This on/off cycling C1 = 1μF is referred to as “hiccup” mode. C2 = 10μF LOAD 2-3 INCHES (51-76mm) FROM MODULE Output Fusing Figure 2. Measuring Output Ripple and Noise (PARD) The converter is extensively protected against current, voltage and temperature extremes. However, your application circuit may need additional protection. In the Minimum Output Loading Requirements extremely unlikely event of output circuit failure, excessive voltage could be applied These converters employ a synchronous rectifi er design topology. All models to your circuit. Consider using an appropriate external protection. regulate within specifi cation and are stable from 0% load to full load conditions, Output Current Limiting unless otherwise specifi ed. Operation under no load will not damage the con- As soon as the output current increases to approximately its overcurrent limit, verter but might, however, slightly increase regulation, output ripple, and noise. the DC/DC converter will enter a current-limiting mode. The output voltage will Thermal Shutdown decrease proportionally with increases in output current, thereby maintaining a To protect against thermal over-stress, these converters include thermal shut- somewhat constant power output. This is commonly referred to as power limiting. down circuitry. If environmental conditions cause the temperature of the DC/ Current limiting inception is defi ned as the point at which full power falls DC’s to rise above the Operating Temperature Range up to the shutdown tem- below the rated tolerance. See the Performance/Functional Specifi cations. perature, an on-board electronic temperature sensor will power down the unit. Note particularly that the output current may briefl y rise above its rated value. When the temperature decreases below the turn-on threshold, the converter This enhances reliability and continued operation of your application. If the will automatically restart. There is a small amount of hysteresis to prevent output current is too high, the converter will enter the short circuit condition. rapid on/off cycling. CAUTION: If you operate too close to the thermal limits, the converter may shut down suddenly without warning. Be sure to thoroughly test Output Short Circuit Condition your application to avoid unplanned thermal shutdown. When a converter is in current-limit mode, the output voltage will drop as the output current demand increases. If the output voltage drops too low, the Temperature Derating Curves magnetically coupled voltage used to develop PWM bias voltage will also drop, The graphs in the performance data section illustrate typical operation under a thereby shutting down the PWM controller. Following a time-out period, the variety of conditions. The Derating curves show the maximum continuous ambient PWM will restart, causing the output voltage to begin rising to its appropriate air temperature and decreasing maximum output current which is acceptable under value. If the short-circuit condition persists, another shutdown cycle will initi- increasing forced airfl ow measured in Linear Feet per Minute (“LFM”). Note that ate. This on/off cycling is called “hiccup mode.” The hiccup cycling reduces the these are AVERAGE measurements. The converter will accept brief increases in tem- average output current, thereby preventing excessive internal temperatures. perature and/or current or reduced airfl ow as long as the average is not exceeded. Trimming the Output Voltage Note that the temperatures are of the ambient airfl ow, not the converter it- The Trim input to the converter allows the user to adjust the output voltage over self which is obviously running at higher temperature than the outside air. Also the rated trim range (please refer to the Specifi cations). In the trim equations note that “natural convection” is defi ned as very low fl ow rates which are not and circuit diagrams that follow, trim adjustments use a single fi xed resistor using fan-forced airfl ow. Depending on the application, “natural convection” is connected between the Trim input and either Vout pin. Trimming resistors should usually about 30-65 LFM but is not equal to still air (0 LFM). have a low temperature coeffi cient (±100 ppm/°C or less) and be mounted close Murata Power Solutions makes Characterization measurements in a closed to the converter. Keep leads short. If the trim function is not used, leave the trim cycle wind tunnel with calibrated airfl ow. We use both thermocouples and an unconnected. With no trim, the converter will exhibit its specifi ed output voltage infrared camera system to observe thermal performance. As a practical matter, accuracy. it is quite diffi cult to insert an anemometer to precisely measure airfl ow in There are two CAUTIONs to observe for the Trim input: most applications. Sometimes it is possible to estimate the effective airfl ow if you thoroughly understand the enclosure geometry, entry/exit orifi ce areas and CAUTION: To avoid unplanned power down cycles, do not exceed EITHER the fan fl owrate specifi cations. the maximum output voltage OR the maximum output power when setting the trim. If the output voltage is excessive, the OVP circuit may inadvertantly shut CAUTION: If you exceed these Derating guidelines, the converter may have down the converter. If the maximum power is exceeded, the converter may an unplanned Over Temperature shut down. Also, these graphs are all collected near Sea Level altitude. Be sure to reduce the derating for higher altitude. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 34 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters enter current limiting. If the power is exceeded for an extended period, the con- There are two CAUTIONs for the On/Off Control: verter may overheat and encounter overtemperature shut down. CAUTION: While it is possible to control the On/Off with external logic if you CAUTION: Be careful of external electrical noise. The Trim input is a senstive carefully observe the voltage levels, the preferred circuit is either an open input to the converter’s feedback control loop. Excessive electrical noise may drain/open collector transistor or a relay (which can thereupon be controlled by cause instability or oscillation. Keep external connections short to the Trim logic). The On/Off prefers to be set at approx. +15V (open pin) for the ON state, input. Use shielding if needed. assuming positive logic. CAUTION: Do not apply voltages to the On/Off pin when there is no input Trim Equations power voltage. Otherwise the converter may be permanently damaged. Trim Up Trim Down between Trim and +Vout> +VOUT +VIN SPM15-033-Q12, Q48 12775 5110 (Vo - 2.5) RT (Ω) = – 2050 RT (Ω) = – 2050 UP DOWN VO – 3.3 3.3 – VO ON/OFF TRIM LOAD SPM15-050-Q12, Q48 CONTROL RTRIM DOWN 12775 5110 x (Vo –2.5) – 2050 RT (Ω) = – 2050 RT (Ω) = UP DOWN 5 – VO VO – 5 SPM15-120-Q12, Q48 −VIN −VOUT 10000 (Vo-2.5) 25000 – 5110 – 5110 RT (Ω) = RT (Ω) = UP DOWN 12 – VO VO – 12 Figure 3. Trim adjustments to decrease Output Voltage using a Fixed Resistor SPM15-150-Q12, Q48 25000 10000 (Vo-2.5) – 5110 RT (Ω) = – 5110 RT (Ω) = UP DOWN +VOUT +VIN 15 – VO VO – 15 Where Vo = Desired output voltage. Adjustment accuracy is subject to resis- tor tolerances and factory-adjusted output accuracy. Mount trim resistor close ON/OFF TRIM LOAD to converter. Use short leads. CONTROL R TRIM UP Remote On/Off Control On the input side, a remote On/Off Control can be specifi ed with either positive −VIN −VOUT or negative logic as follows: Positive: Models equipped with Positive Logic are enabled when the On/Off Figure 4. Trim adjustments to increase Output Voltage using a Fixed Resistor pin is left open or is pulled high to +15VDC with respect to –VIN. An internal bias current causes the open pin to rise to +VIN. Positive-logic devices are disabled when the On/Off is grounded or brought to within a low voltage (see Specifi ca- +VCC tions) with respect to –VIN. Negative: Models with negative logic are on (enabled) when the On/Off is grounded or brought to within a low voltage (see Specifi cations) with respect to ON/OFF CONTROL –VIN. The device is off (disabled) when the On/Off is left open or is pulled high to +15VDC Max. with respect to –VIN. -VIN Dynamic control of the On/Off function should be able to sink the specifi ed signal current when brought low and withstand specifi ed voltage when brought high. Be aware too that there is a fi nite time in milliseconds (see Specifi cations) between the time of On/Off Control activation and stable, regulated output. This Figure 5. Driving the On/Off Control Pin (suggested circuit) time will vary slightly with output load type and current and input conditions. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 35 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om MURATA SPM15 Series SPM15 SERIES 15 Watt Ultra-Wide 4:1 Input Range DC-DC Converter Single Output Potted Metal Package Measures: 1.00 x 1.00 x 0.41” Isolated 15-Watt DC-DC Converters Vertical Wind Tunnel Murata Power Solutions employs a computer controlled custom-designed closed loop vertical wind tunnel, infrared video camera system, and test instrumentation for accurate airfl ow and heat dissipation analysis of power products. IR Transparent The system includes a precision low fl ow-rate anemometer, optical window Variable variable speed fan, power supply input and load controls, Unit under speed fan temperature gauges, and adjustable heating element. test (UUT) The IR camera monitors the thermal performance of the IR Video Unit Under Test (UUT) under static steady-state conditions. A Camera special optical port is used which is transparent to infrared wavelengths. Both through-hole and surface mount converters are soldered down to a 10˝ X10˝ host carrier board for realistic heat absorption and spreading. Both longitudinal and trans- Heating verse airfl ow studies are possible by rotation of this carrier element board since there are often signifi cant differences in the heat Precision dissipation in the two airfl ow directions. The combination of low-rate adjustable airfl ow, adjustable ambient heat, and adjustable anemometer Input/Output currents and voltages mean that a very wide 3” below UUT range of measurement conditions can be studied. The collimator reduces the amount of turbulence adjacent Ambient to the UUT by minimizing airfl ow turbulence. Such turbu- temperature lence infl uences the effective heat transfer characteristics sensor and gives false readings. Excess turbulence removes more heat from some surfaces and less heat from others, possibly Airflow causing uneven overheating. collimator Both sides of the UUT are studied since there are different thermal gradients on each side. The adjustable heating element and fan, built-in temperature gauges, and no-contact IR camera mean Figure 6. Vertical Wind Tunnel that power supplies are tested in real-world conditions. Soldering Guidelines Murata Power Solutions recommends the specifi cations below when installing these converters. These specifi cations vary depending on the solder type. Exceeding these specifi ca- tions may cause damage to the product. Be cautious when there is high atmospheric humidity. We strongly recommend a mild pre-bake (100° C. for 30 minutes). Your production environment may differ; therefore please thoroughly review these guidelines with your process engineers. Wave Solder Operations for through-hole mounted products (THMT) For Sn/Ag/Cu based solders: For Sn/Pb based solders: Maximum Preheat Temperature 115° C. Maximum Preheat Temperature 105° C. Maximum Pot Temperature 270° C. Maximum Pot Temperature 250° C. Maximum Solder Dwell Time 7 seconds Maximum Solder Dwell Time 6 seconds This product is subject to the following operating requirements Murata Power Solutions, Inc. and the Life and Safety Critical Application Sales Policy: 11 Cabot Boulevard, Mansfi eld, MA 02048-1151 U.S.A. Refer to: http://www.murata-ps.com/requirements/ ISO 9001 and 14001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi cations are subject to change without notice. © 2015 Murata Power Solutions, Inc. www.murata-ps.com/support Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. MDC_SPM15.C02 Page 36 of 36 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/murata-spm15-dc-dc-converter.html h t t p: / / pow e r. sa ge r. c om