OHMITE OD361J

OD/OF Series ® Little Demon Carbon Composition Molded 5% & 10% Tolerance FeatureS Ohmite’s Little Demons are small, reliable carbon composition resistors with exceptional strength. • Molded insulation for high dielectric strength They are made tough by a molding process that • Rugged construction combines the terminals, insulation and resistive ele- • High surge capabilities ment into an integrated unit. Along with their small size, Little Demons perform with low noise, dissipate • Comparable to “Mil” RC07, RC20, and RC32 types heat rapidly and offer high temperature stability. • OD/OF Series available in E24 values; E12 values Color codes are readable even after prolonged use above 100KΩ thanks to a very durable coating that resists abra- sions and chipping normally associated with auto- matic insertion equipment. SerieS SpeciFicatiOnS Series Mil-R-11 Type Wattage Ohms Tolerance Max. Voltage Dielectric VAC OD RC07 0.25 2.2Ω - <100K ±5% 250 500 100K - 5.6M ±10% OF RC20 0.50 2.2Ω - <100K ±5% 350 700 100K - 20M ±10% characteriSticS 100,000 Terminals Solder-coated copper terminal. Single Pulse Power Capability Molded Phenolic Body 10,000 Tolerance ±5% (<100KΩ); OF 1,000 ±10% (>100KΩ) OD Derating Linearly from 100% @ +70°C to 0% @ 130°C 100 10 1 -7 -6 -5 -4 -3 -2 -1 10 10 10 10 10 10 10 1 Pulse width (s) DimenSiOnS Series Length max. Diam. max. Lead Dia. 1.135" ±0.12 D L OD 0.276 / 7.0 0.098 / 2.5 0.024/0.60 28.83mm ±3 OF 0.406 /10.3 0.150 / 3.8 0.028/0.70 (continued) 92 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com Pulse Power (W) 75mm ±5 OD/OF Series ® Little Demon Carbon Composition Molded 5% & 10% Tolerance packaging All resistors are packaged in sealed poly bags with desiccant Storage: Ohmite recommends storing carbon composition to maintain a consistent humidity during storage. If parts are resistors in a controlled environment at a temperature of 5° to removed from the protective plastic bag they should be used 35°C and relative humidity of less than 60%. Inventory should as soon as possible or resealed in the plastic bag. always be used on a first-in-first-out basis. Tape/Reel OD OF 0.5mm max. 6mm ±.5 Qty./reel 5000 3000 +1.6 52.4mm Reel size (mm) 260 260 -1.4 Qty./carton 40,000 24,000 260mm Gross carton wt. (kg) 12 13 ±5 3 Carton size (m ) 0.04 0.04 275mm ±5 (OD) 5.08mm ±.38 455mm ±5 (OF) Ammo Box OD OF 1mm max. Tape width (mm) 52 52 Qty./box 2000 2000 60mm ±5 (OD) 14.5mm ±.5 Qty./carton 30,000 30,000 65mm ±5 (OF) Gross carton wt. (kg) 10 16 Carton size (m3) 0.03 0.05 L L 3.2mm min. 3mm 1 2 75mm ±5 L – L = 1mm max. 1 2 60.4mm±1 60.4mm ±1 reSiStOr uSe guiDelineS Carbon composition resistors are manufactured by extruding moisture and, therefore, storage recommendations should be a blend of carbon and organic binders inside a phenolic outer adhered to. Generally, any moisture absorbed during storage body. The extrusion is cut to length, leads inserted, cured, will be "baked out" during the soldering operation. If the prod- and marked to form a finished resistor. The carbon and binder uct is stored properly the resistance shift during the soldering mixture is adjusted to produce different resistance values. The operation will be minimal, less than 2% or 3%. resistors are sorted for 5%, 10%, and 20% tolerance values. Carbon composition resistors are highly hygroscopic and Carbon composition resistors are able to withstand larger changes in resistance value can occur if too much moisture is short-term pulses and higher voltages than film resistors and absorbed. For this reason, it is recommended not to use water are virtually impervious to ESD events (Electro-static dis- or water-soluble solvents to clean these components. Alcohol charge). Carbon composition resistors are also sensitive to or hydrocarbon solvents are recommended for rinsing. bake prOceDure A. Heat Treatment C. Solder heat test after treatment D. Cautions 110°C ±10°C Solder Dip Solderability: may be affected due to oxidization of lead wire 15 hours Type Temp. Time Evaluation Resistance value: some units may not completely recover to B. Frequency of OD 300°C 3 sec within ±3% original value. heat treatment OF 350°C 3 sec within ±3% Soldering heat: some treated product may have substantial 1 time only resistance change during soldering operation. It is recom- *Depth of Immersion: 3mm from the resistor mended that parts be tested to evaluate soldering heat body effects. OrDering inFOrmatiOn • OD/OF Series available in E24 values RoHS compliant OD683JE -TR Series Ohms Tolerance Packaging OD 68G= 6.8 None = cut reel, 100/bag (std.) <100KΩ : J = 5% OF -TR = taped and reeled 680 = 68 >100KΩ : K = 10% -A = ammo pack 681 = 680 -B = bulk (loose) 682 = 6,800 683 = 68,000 684 = 680,000 rev 5/18-2 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com 93 280mm (ref.)