Floatless Level Switch (Ultra High-sensitivity Type) 61F-UHS/-HSL CSM_61F-UHS_-HSL_DS_E_3_3 Ideal for Detecting Ice, Pure Water, or Humidity • Applicable for detecting ice, pure water steam, humidity, or other substances that conduct electricity poorly. Two types of model available: Ul tra high-sensitivity and variable ultra high-sensitivity. Refer to Safety Precautions for Floatless Level Controllers. ■ Ordering Information Type Ultra high-sensitivity Variable ultra high- sensitivity Model Model Ultra high- 61F-UHS 61F-HSL sensitivity Note: When ordering, specify the desired operating voltage at the end of the model number. Example: 61F-UHS [220VAC] Desired supply voltage ■ Ultra High-sensitivity Models Use these models for sensing objects such as ice, high-purity distilled water, moisture, or other objects with low electrical conductivity. Specifications Item High-sensitivity 61F-UHS Variable high-sensitivity 61F-HSL Supply voltage 100, 200, or 220 VAC; 50/60 Hz 24, 100, 110, 200, or 220 VAC; 50/60 Hz Operating voltage range 85% to 110% of rated voltage Interelectrode voltage 24 VAC 13 VDC max. Interelectrode current Approx. 1 mA AC max. Approx. 1 mA DC max. Power consumption 3.2 VA max. Interelectrode operate resistance 0 to approx. 1 MΩ (see note 1) 0 to approx. 5 MΩ (variable) Interelectrode release resistance Approx. 5 M to ∞Ω Operate resistance + 2.5 MΩ max. Cable length 5 m (see note 2) (see note 3) Control output 0.3 A, 220 VAC (Inductive load: cosφ = 0.4) 2 A, 220 VAC (Inductive load: cosφ = 0.4) 1 A, 220 VAC (Resistive load) 5 A, 220 VAC (Resistive load) Ambient temperature Operating:–10 to 55°C Ambient humidity Operating:45% to 85% RH Insulation resistance 100 MΩ max. (at 500 VDC) Dielectric strength 2,000 VAC, 50/60 Hz for 1 min Life expectancy Electrical: 50,000 operations min. Electrical: 500,000 operations min. Mechanical: 5,000,000 operations min. Mechanical: 5,000,000 operations min. Weight Approx. 380 g Approx. 240 g Note: 1. Use 61F-UHS for detecting water leakage with high specific resistance. Connect a sensor cable between terminals 1 and 7. 2. Two Electrodes can be connected to the 61F-HSL. Use them for an alarm, not for creating a self-holding circuit. 2 3. The length when using completely-insulated, 600-V, 3-conductor (0.75 mm ) cabtire cables. Usable cable lengths will become shorter as the cable diameter or number of conductors becomes larger. For more details, refer to Safety Precautions for Floatless Level Controllers. 4. It is recommended that the cable length be kept as short as possible since the Electrode circuit current is at DC micro-current level. More- over, the Electrodes will corrode rapidly if the current is allowed to constantly flow between the Electrodes. Be careful with the electrode polarity and grounding when wiring. 1 61F-UHS/-HSL Internal Circuit Diagrams 61F-UHS 61F-HSL S S1 1 66 Relay Rectification/ S1 5 smoothing To each circuit circuit Power supply To each circuit Power supply S S2 2 55 Rela Relay y S2 6 11 E E3 3 7 77 E E1 1 1 Relay 88 E E2 2 X/a X/a 8 Ground 22 T Tbb Tb 2 Tc 44 X/c X/c Tc 4 X/c 33 T Ta a 3 Ta External Circuit Diagrams (Example) 61F-UHS 61F-HSL Power Power 4 4 5 5 source source 3 6 3 6 2 7 2 7 8 8 1 1 E3 E2 E1 (+) (-) Socket: 8PFA1 (track mounted)/ Socket: 8PFA (track mounted)/ PL08 (back connecting) PL08 (back connecting) 2 Operation power supply Rectification Level detection circuit Power circuit Operation power supply Surge-absorbing Rectification circuit Level detection Constant voltage circuit circuit Power circuit smoothing circuit smoothing circuit 61F-UHS/-HSL ■ Connections Automatic Water Supply and Drainage Control Ultra High-sensitivity Type Dimensions: Page 4 Automatic Water Supply Control Automatic Drainage Control Connections Connections Commercial Voltage Commercial Voltage RS T RS T 61F-UHS 61F-UHS 65 4 3 654 3 MCCB MCCB 0 V 0 V U U Control Control 24 V U 24 V U circuit circuit 24 V 24 V Power Power U U supply supply 71 8 2 71 8 2 (See Contac- Contac- (See note.) note.) tor tor PS-3S Motor Motor protection PS-3S Stop protection Water supply Water relay relay E1 Start source tank E2 Start Wastewater E1 E3 E2 Stop tank E3 M P M P Reservoir Note: Be sure to ground the common Electrode E3 (the Note: Be sure to ground the common Electrode E (the 3 longest Electrode). longest Electrode). Connection Sockets Connection Sockets 8PFA1 (Front-connecting) 8PFA1 (Front-connecting) PL08 (Read-connecting) PL08 (Read-connecting) Connect terminal 2 to the contactor coil terminal. Connect terminal 3 to the contactor coil terminal. Principles of Operation Principles of Operation Water supply P Indicator ON Indicator ON Pump OFF Pump ON E1 E1 Pump ON Pump OFF Indicator OFF Indicator OFF E2 E2 P E3 E3 Water drainage • When the water level reaches E , the pump stops and, When the water level reaches E , the pump starts and, 1 1 when the water level reaches E or below, the pump when the water level reaches E or below, the pump 2 2 starts. stops. 3 61F-UHS/-HSL Dimensions Note: All units are in millimeters unless otherwise indicated. 61F-UHS 5 91 72 71.2 61F-UHS 101 3.5 82 7 8PFA1 24 97.5 60 61F-HSL 5 5.6 80 62 61 61F-HSL 113 3.5 72.6 7 49 91 8PFA 99.3 ■ Electrode Holders PS-3S/-4S/-5S PS-3SR/-4SR/-5SR Mounting Holes (see note) PF2 parallel thread Used with (effective dia.: 58.135) 9-dia. rubber coupling bushing (inner) 34 dia. With Mounting Bracket 65 dia. hole PS-3S (approx. 150 g) PS-4S (approx. 170 g) PS-5S (approx. 185 g) PS-3SR (approx. 155 g) PS-4SR (approx. 175 g) PS-5SR (approx. 190 g) Mounting Screw Holes Note: The PS-3SR, PS-4SR, and PS-5SR have built-in resistor of 6.8 kΩ and used for the two-wire 61F models. PS-31 PF1/2 Parallel thread Mounting Holes 11 dia. Weight: approx. 325 g Electrode Rubber SUS304 packing 3 M3 29.5 dia. F03-31 Dust-preventive rubber cap (optional) Weight: approx. 20 g Note: Standard holder construction includes three integral 300-mm-long Electrodes. However, a model having 1,000-mm-long Electrodes is available on request. 4 61F-UHS/-HSL (72) BF-1 Two, M5 × 25 23 8 22 mounting screws Mounting Holes 26-dia. 60 (48) 33 dia. (20 dia.) 48 hole Terminal bolt, SUS304 (M6) Weight: approx. 75 g Nuts (M6) Two, 6-dia. holes (18) 40±2.0 (47) BF-3/-3R BF-3(R) Weight BF-5/-5R BF-3: approx. 210 g BF-3R: approx. 215 g Two, 6-dia. holes Mounting Holes R19 64-dia. hole 1 1 Three, 26-dia. holes 120° 110 (90) 90 90 120° Two, 6-dia. holes Two, M5 × 25 mounting screws Nut 74 Terminal (M6) bolt, SUS304 (M6) BF-5(R) Weight BF-5: approx. 360 g 20 dia. BF-5R: approx. 365 g Mounting Holes Two, 6-dia. hole Five, 26-dia. hole R13 Spring washer 110 dia.(90) 50 90 76 90 (18) 23 8 22 ±2.0 (49) 40 50 76 (47) (72) BS-1 BS-1(S) Weight: approx. 70 g Width across flats: 20 Terminal bolt Two, M4 P=0.7 M18 Mounting Holes SUS304 (M4) P=0.7 P=1.5 24 Nut (iron) 12 39 50 51 101 M18 P=1.5 (fine screw thread) BS-1S Width across flats: 20 BS-1S-1 Terminal bolt M18 Two, M4 P=0.7 BS-1S2 SUS304 (M4) P=0.7 P=1.5 24 dia. 12 39 50 51 M18 P=1.5 101 (fine screw thread) 5 61F-UHS/-HSL Terminal bolt SUS304 BS-1T SUS316 Mounting Holes Titanium HAS B HAS C M4 nut Width between SUS304 Two, M4** flats: 20.5 24 dia. M18 P=1.5 (fine screw thread) HAS titanium *This nut is made of Fluorine Resin **A connecting nut made of HAS B, HAS C, or titanium is not supplied with two M4 screws and thus has no holes for such screws. Material SUS304 SUS316 Titanium HAS B HAS C Weight Approx. 55 g Approx. 55 g Approx. 45 g Approx. 65 g Approx. 60 g PH-1 PH-2 (Approx. 140 g with a 1-m cord) (Approx. 235 g with a 1-m cord) Two, 6-dia. holes PVC resin (black) Resin 26 dia. 27 dia. 5 dia. 19 dia. Two-core cable Single-core cable Cable OD: Vinyl, Hypalon 6.8 dia. Cable OD: Vinyl 5.0 dia., Hypalon 6.5 dia. Note: Cable is supplied in lengths of 1, 5, 10, 15, 20, 30, 40, 50, 60, 70, 80, 90, or 100 meters. ■ Electrode Separators F03-14 1P for one pole F03-14 3P for three poles F03-14 5P for five poles Five, 7 dia. Three, 7 dia. 6.5 dia. 20 20 28 dia. 41 46 Weight: Approx. 15 g Weight: Approx. 30 g Weight: Approx. 30 g ■ Safety Precautions Refer to Safety Precautions for All Level Controllers. Precautions for Correct Use Short Wiring in Electrode Circuit • Keep the wires connecting the Controller to Electrode Holders as short as possible. If long leads are used, the floating capacity of the leads, and abnormal surges or noise in the Electrode circuit can cause malfunctions. The thicker the cables, the shorter the permitted wiring length. The length of the cable connecting the Controller and Electrode is specified in the Controller datasheet as a guideline assuming that a 2 600-V VCT 0.75-mm , 3-core cabtire cable is used. Test results 2 indicate that the actual wiring length using VCT 3.5-mm , 3-core cable laid over the ground is 50% of the specified length for general-purpose applications and 80% of the specified length for long-distance applications. When selecting cable specifications, remember that the wiring length is further decreased for underground cables and larger diameter cables because of the increased floating capacity with the ground. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. In the interest of product improvement, specifications are subject to change without notice. 6 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2015.10 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2015 All Right Reserved.