Spatter-resistant Proximity Sensor E2EQ CSM_E2EQ_DS_E_9_1 Spatter-resistant Fluororesin- coated Proximity Sensor • Superior spatter resistance. Long Sensing-distance Models added for sensing distances up to 15 mm. Pre-wired Smartclick Connector Models are also available. For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Be sure to read Safety Precautions on page 6. Ordering Information Sensors [Refer to Dimensions on page 7.] Pre-wired Models Long Sensing-distance Models Appearance Sensing distance Output configuration Operation mode Model M12 E2EQ-X4X1 2M 4 mm Shielded DC 2-wire M18 NO E2EQ-X8X1 2M 8 mm (no polarity) M30 E2EQ-X15X1 2M 15 mm Standard Models Appearance Sensing distance Output configuration Operation mode Model M12 E2EQ-X3D1 2M 3 mm Shielded M18 DC 2-wire NO E2EQ-X7D1 2M 7 mm M30 E2EQ-X10D1 2M 10 mm Pre-wired Smartclick Connector Models (M12) Long Sensing-distance Models Appearance Sensing distance Output configuration Operation mode Model M12 E2EQ-X4X1-M1TJ 0.3M 4 mm DC 2-wire Shielded (no polarity) M18 NO E2EQ-X8X1-M1TJ 0.3M 8 mm (3)-(4) pin arrangement M30 E2EQ-X15X1-M1TJ 0.3M 15 mm Standard Models Standard Models Sensing distance Output configuration Operation mode Model M12 E2EQ-X3D1-M1TGJ 0.3M 3 mm DC 2-wire Shielded M18 (1)-(4) NO E2EQ-X7D1-M1TGJ 0.3M 7 mm pin arrangement M30 E2EQ-X10D1-M1TGJ 0.3M 10 mm 1 E2EQ Pre-wired Connector Models (M12) Long Sensing-distance Models Appearance Sensing distance Output configuration Operation mode Model M12 E2EQ-X4X1-M1J 0.3M 4 mm DC 2-wire Shielded (without polarity) M18 NO E2EQ-X8X1-M1J 0.3M 8 mm (3)-(4) pin arrangement M30 E2EQ-X15X1-M1J 0.3M 15 mm Standard Models Standard Models Sensing distance Output configuration Operation mode Model M12 E2EQ-X3D1-M1GJ 0.3M 3 mm DC 2-wire Shielded M18 (1)-(4) NO E2EQ-X7D1-M1GJ 0.3M 7 mm pin arrangement M30 E2EQ-X10D1-M1GJ 0.3M 10 mm Accessories (Order Separately) Sensor I/O Connectors (M12, Sockets on One Cable End) (Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) [Refer to XS2, XS5.] Appearance Cable length Sensor I/O Connector model number Applicable Proximity Sensor model number 2 m XS2F-D421-DC0-F Straight 5 m XS2F-D421-GC0-F E2EQ-X@X1-M1J 2 m XS2F-D422-DC0-F L-shape 5 m XS2F-D422-GC0-F 2 m XS2F-D421-DA0-F Straight 5 m XS2F-D421-GA0-F E2EQ-X@D1-M1GJ 2 m XS2F-D422-DA0-F L-shape 5 m XS2F-D422-GA0-F 2 m XS5F-D421-D80-F Smartclick E2EQ-X@X1-M1TJ Connector E2EQ-X@D1-M1TGJ 5 m XS5F-D421-G80-F Straight Note: Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details. Ratings and Specifications Long Sensing-distance Models Model E2EQ-X4X1 E2EQ-X8X1 E2EQ-X15X1 E2EQ-X4X1-M1(T)J E2EQ-X8X1-M1(T)J E2EQ-X15X1-M1(T)J Item Sensing distance 4 mm ±10% 8 mm ±10% 15 mm ±10% Set distance *1 0 to 3.2 mm 0 to 6.4 mm 0 to 12 mm Differential travel 15% max. of sensing distance Standard sensing object Iron, 12 × 12 × 1 mm Iron, 18 × 18 × 1 mm Iron, 30 × 30 × 1 mm Response frequency *2 1 kHz 0.5 kHz 0.25 kHz Load current 3 to 100 mA Control output Residual voltage *3 5 V max. (Load current: 100 mA, Cable length: 2 m) Operation mode (with sensing Load ON: NO; For details, refer to the timing charts on page 5. object approaching) Protection circuits Load short-circuit protection, Surge suppressor Ambient temperature range Operating: −25 to 70°C, Storage: −40 to 85°C, (with no icing or condensation) ±15% max. of sensing distance at 23°C in the temperature range of −40 to 85°C ±15% max. of sensing distance at 23°C in Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C the temperature range of −25 to 70°C Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range 2 Shock resistance Destruction: 1,000m/s 10 times each in X, Y, and Z directions Connection method Pre-wired Models (Standard cable length: 2 m), Pre-wired Connector Models Pre-wired Models Approx. 65 g Approx. 140 g Approx. 190 g Weight (packed Pre-wired Approx. 20 g Approx. 40 g Approx. 90 g state) Connector Models *1. Use the Sensor within the range in which the green indicator is ON. *2. The response frequency is an average value. *3. The residual voltage is 5 V. Make sure that the device connected to the Sensor can withstand the residual voltage. 2 E2EQ Standard Models Model E2EQ-X3D1 E2EQ-X7D1 E2EQ-X10D1 E2EQ-X3D1-M1(T)GJ E2EQ-X7D1-M1(T)GJ E2EQ-X10D1-M1(T)GJ Item Sensing distance 3 mm ±10% 7 mm ±10% 10 mm ±10% Set distance 0 to 2.4 mm 0 to 5.6 mm 0 to 8 mm Differential travel 10% max. of sensing distance Standard sensing object Iron, 12 × 12 × 1 mm Iron, 18 × 18 × 1 mm Iron, 30 × 30 × 1 mm Response frequency * 1 kHz 500 Hz 400 Hz Load current 3 to 100 mA Control output Residual voltage 3 V max. (Load current: 100 mA, Cable length: 2 m) Operation mode (with sensing Load ON: NO; For details, refer to the timing charts on page 5. object approaching) Protection circuits Load short-circuit protection, Surge suppressor Ambient temperature range Operating/Storage: −25 to 70°C (with no icing or condensation) Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C Voltage influence ±2.5% max. of sensing distance at rated voltage in the rated voltage ±15% range 2 Shock resistance Destruction: 1,000 m/s 10 times each in X, Y, and Z directions E2EQ-X@D1: Pre-wired Models (Standard cable length: 2 m) Connection method E2EQ-X@D1-M1GJ: Pre-wired Connector Models (Standard cable length: 300mm) Pre-wired Models Approx. 120 g Approx. 160 g Approx. 220 g Weight (packed Pre-wired Approx. 80 g Approx. 110 g Approx. 190 g state) Connector Models * The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. Common Ratings and Performance Model E2EQ-X4X1 E2EQ-X8X1 E2EQ-X15X1 E2EQ-X4X1-M1(T)J E2EQ-X8X1-M1(T)J E2EQ-X15X1-M1(T)J E2EQ-X3D1 E2EQ-X7D1 E2EQ-X10D1 Item E2EQ-X3D1-M1(T)GJ E2EQ-X7D1-M1(T)GJ E2EQ-X10D1-M1(T)GJ Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page Detectable object 4.) Power supply voltage 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. (operating voltage range) Leakage current 0.8 mA max. Indicators Operation indicator (red), Setting indicator (green) Ambient humidity range Operating/Storage: 35% to 95% (with no condensation) Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case Dielectric strength 1,000 VAC for 1 min between current-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Degree of protection IEC 60529 IP67, in-house standards: oil-resistant Case Fluororesin coating (Base material: brass) Sensing surface Fluororesin Materials Clamping nuts Fluororesin coating (Base material: brass) Toothed washer Zinc-plated iron Accessories Instruction manual 3 E2EQ Engineering Data (Reference Value) Sensing Area E2EQ-X@X@(-M1(T)J) Shielded Models E2EQ-X@D@(-M1(T)GJ) 18 16 E2EQ-X15X 10 14 E2EQ-X10D1 8 12 E2EQ-X8X 10 6 E2EQ-X4X E2EQ-X7D1 E2EQ-X3D1 8 4 6 Y X 4 2 2 0 −20 −16 −12 −8 −4 0 4 8 12 16 20 −20 −15 −10 −5 0 5 10 15 20 Distance Y Distance Y (mm) E2EQ-X3D1 Sensing Head (mm) E2EQ-X7D1 Sensing Head E2EQ-X10D1 Sensing Head Influence of Sensing Object Size and Material E2EQ-X4X1(-M1(T)J) E2EQ-X8X1(-M1(T)J) E2EQ-X15X1(-M1(T)J) 5 10 20 d × d × d × d d d t = 1 mm t = 1 mm t = 1 mm X X X 4 Iron 8 Iron 16 Stainless steel Iron (SUS304) 3 6 12 Stainless steel Stainless steel (SUS304) (SUS304) Brass 2 4 Brass 8 Copper Brass Copper Aluminum 1 2 4 Copper 0 5 10 15 20 25 30 35 0 10 20 30 40 50 0 10 20 30 40 50 60 70 80 Side length of sensing object: d (mm) Side length of sensing object: d (mm) Side length of sensing object: d (mm) E2EQ-X3D1(-M1(T)GJ) E2EQ-X7D1(-M1(T)GJ) E2EQ-X10D1(-M1(T)GJ) 4.0 10 14 d × d × d × d 9 d d t = 1 mm t = 1 mm 3.5 t = 1 mm 12 X X X 8 3.0 10 Iron Iron 7 Iron Stainless steel 2.5 (SUS304) 6 8 Stainless steel 2.0 5 (SUS304) Aluminum Stainless steel 6 4 (SUS304) 1.5 Brass Brass Brass 3 4 Aluminum 1.0 Copper 2 Copper Copper Aluminum 2 0.5 1 0 5 10 15 20 25 30 35 0 510 15 20 25 30 35 40 45 0 5 10 15 20 25 30 35 40 45 50 55 Side length of sensing object: d (mm) Side length of sensing object: d (mm) Side length of sensing object: d (mm) 4 Distance X (mm) Distance X (mm) Distance X (mm) Distance X (mm) Distance X (mm) Distance X (mm) Distance X (mm) Distance X (mm) X Y E2EQ Residual Output Voltage Leakage Current E2EQ-X@X@(-M1(T)J) E2EQ-X@D@(-M1(T)GJ) E2EQ-X@D 5 1.5 5 4 4 1.0 3 3 E2EQ-X3D1 2 2 0.5 1 1 E2EQ-X10D1 E2EQ-X7D1 0 0 1 3 5 10 30 50 100 1 3 5 10 30 50 100 300 500 1,000 0 10 20 30 40 Load current (mA) Load current (mA) Power supply voltage (V) I/O Circuit Diagrams Long Sensing-distance Models Operation Model Timing Chart Output circuit mode Brown 4 Load +V Set position Unstable Proximity Sensor sensing main Non-sensing area Stable sensing area area circuit Blue 3 0 V Sensing E2EQ-X4X1 object E2EQ-X8X1 Note 1. The load can be connected to either the +V or E2EQ-X15X1 100 80 (TYP) 0 (%) 0 V side. NO Rated E2EQ-X4X1-M1(T)J Note 2. There is no polarity. Therefore, the brown and sensing ON Setting indicator E2EQ-X8X1-M1(T)J blue lines have no polarity. distance (green) OFF E2EQ-X15X1-M1(T)J Operation indicator Connector Pin Arrangement ON (red) OFF 1 ON Control output 2 4 OFF 3 Note: Pins 1 and 2 are not used. Standard Models Operation Model Timing Chart Output circuit mode Brown Set position Unstable 1 Load +V sensing Non-sensing area area Stable sensing area Proximity Sensor Proximity Sensor main Sensing circuit object Blue E2EQ-X3D1 4 0 V E2EQ-X7D1 (%) 100 80 (TYP) 0 Note: The load can be connected to either the +V E2EQ-X10D1 NO Rated or 0 V side. E2EQ-X3D1-M1(T)GJ sensing ON Setting indicator E2EQ-X7D1-M1(T)GJ distance (green) OFF E2EQ-X10D1-M1(T)GJ Connector Pin Arrangement ON Operation 1 indicator (red) OFF 2 4 ON 3 Control output OFF Note: Pins 2 and 3 are not used. 5 Residual output voltage (V) Residual output voltage (V) Leakage current (mA) Main Main circuit circuit Main Main circuit circuit E2EQ Pre-wired Connector Model Connections Model E2EQ-X@X1-M1(T)J E2EQ-X@D1-M1(T)GJ Pre-wired Connector Sensor I/O Connector Pre-wired Connector Sensor I/O Connector Model XS2F-D42@-@C0-F Model XS2F-D42@-@A0-F E2EQ-X@D1-M1GJ E2EQ-X@X1-M1J 1 1 1 1 Brown Brown (+) 2 2 (not used) 2 2 3 3 Blue (−) 3 3 4 4 4 4 Black (+) Blue (−) Connections Pre-wired Connector Pre-wired Connector Sensor I/O Connector Sensor I/O Connector Model Model XS5F-D421-@80-F XS5F-D421-@80-F E2EQ-X@X1-M1TJ E2EQ-X@D1-M1TGJ 1 1 Brown (not used) 1 1 Brown (+) 2 2 White (not used) 2 2 White (not used) 3 3 3 3 Blue (−) Blue (not used) 4 4 Black (+) 4 4 Black (−) Safety Precautions Refer to Warranty and Limitations of Liability. Mutual Interference WARNING When installing two or more Sensors face-to-face or side-by-side, This product is not designed or rated for ensuring ensure that the minimum distances given in the following table are safety of persons either directly or indirectly. maintained. Do not use it for such purposes. B A Precautions for Correct Use Do not use this product under ambient conditions that exceed the Mutual Interference (Unit: mm) ratings. Model Item A B E2EQ-X4X1(-M1(T)J) 30 20 ● Design E2EQ-X8X1(-M1(T)J) 60 35 Influence of Surrounding Metal E2EQ-X15X1(-M1(T)J) 110 90 When mounting the Sensor within a metal panel, ensure that the E2EQ-X3D1(-M1(T)GJ) 30 20 clearances given in the following table are maintained. Failure to E2EQ-X7D1(-M1(T)GJ) 50 35 maintain these distances may cause deterioration in the performance E2EQ-X10D1(-M1(T)GJ) 100 70 of the Sensor. ● Mounting l Do not tighten the nut with excessive force. A washer must be used with the nut. n d dia. m Shielded Model D m l Influence of Surrounding Metal (Unit: mm) Model Item l d D m n Part B Part A E2EQ-X4X1(-M1(T)J) 2.4 18 2.4 12 18 E2EQ-X8X1(-M1(T)J) 3.6 27 3.6 24 27 Note: 1. The allowable tightening strength depends on the distance from the edge of the head, as shown in the following table. (A is the distance E2EQ-X15X1(-M1(T)J) 6 45645 45 from the edge of the head. B includes the nut on the head side. If the E2EQ-X3D1(-M1(T)GJ) 12 818 edge of the nut is in part A, the tightening torque for part A applies E2EQ-X7D1(-M1(T)GJ) 0 18 0 20 27 instead.) 2. The following torque assume washers are being used. E2EQ-X10D1(-M1(T)GJ) 30 40 45 Torque Part A Part B Dimension Model Torque Torque (mm) E2EQ-X4X1(-M1(T)J) 30 N·m E2EQ-X8X1(-M1(T)J) --- 70 N·m E2EQ-X15X1(-M1(T)J) 180 N·m E2EQ-X3D1(-M1(T)GJ) 24 15 N·m --- E2EQ-X7D1(-M1(T)GJ) 29 E2EQ-X10D1(-M1(T)GJ) 26 39 N·m 78 N·m 6 E2EQ (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified. Pre-wired Models Long Sensing-distance Models E2EQ-X4X1 38 9 21 dia. 33 17 4 10 2 *1 Indicators *2 M12 × 1 Two clamping nuts Toothed washer *1. 4-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, 2 Conductor cross section: 0.3 mm , Insulator diameter: 1.3 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) E2EQ-X8X1 E2EQ-X15X1 48 12 42 dia. 43 43 12 38 36 5 10 29 dia. 4 10 3 24 2 *1 *1 Indicators *2 Indicators *2 M18 × 1 Two clamping nuts M30 × 1.5 Two clamping nuts Toothed washer Toothed washer *1. 6-dia. vinyl-insulated round cable with 2 conductors 2 (Flame-resistant, Conductor cross section: 0.5 mm , *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, 2 Insulator diameter: 1.9 mm), Standard length: 2 m Conductor cross section: 0.5 mm , Insulator diameter: 1.9 mm), The cable can be extended up to 200 m (separate Standard length: 2 m metal conduit). The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) *2. Operation indicator (red), Setting indicator (green) Standard Models E2EQ-X3D1 38 27.6 21 dia. 24 17 5 *1 Indicators *2 M12 × 1 4 Two clamping nuts (fluororesin coated) Two toothed washers *1. 6-dia. vinyl-insulated round cable with 2 conductors 2 (Flame-resistant, Conductor cross section: 0.5 mm , Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) E2EQ-X7D1 E2EQ-X10D1 47 56 29 dia. 32 42 dia. 42 24 29 36 38 10 6 *1 Indicators *2 *1 M18 × 1 Two clamping nuts (fluororesin coated) 4 Indicators *2 Two toothed washers Two clamping nuts (fluororesin coated) *1. 6-dia. vinyl-insulated round cable with 2 conductors 5 M30 × 1.5 Two toothed washers 2 (Flame-resistant, Conductor cross section: 0.5 mm , Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, 2 conduit). Conductor cross section: 0.5 mm , Insulator diameter: 1.9 mm), Standard length: 2 m *2. Operation indicator (red), Setting indicator (green) The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) 7 E2EQ Pre-wired Connector Models Long Sensing-distance Models E2EQ-X4X1-M1(T)J 38 9 21 dia. 33 17 4 10 2 Indicators *2 1* M12 × 1 M12 × 1 Toothed Two clamping nuts washer *1. 4-dia. vinyl-insulated round cable (Flame-resistant, 2 Conductor cross section: 0.3 mm , Insulator diameter: 1.3 mm), Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) E2EQ-X8X1-M1(T)J E2EQ-X15X1-M1(T)J 48 12 42 dia. 43 43 12 36 5 10 29 dia. 38 3 24 4 10 2 1* *1 M12 × 1 Indicators *2 Indicators *2 M12 × 1 M18 × 1 M30 × 1.5 Two clamping nuts Toothed Toothed Two clamping nuts washer *1. 6-dia. vinyl-insulated round cable (Flame-resistant, washer *1. 6-dia. vinyl-insulated round cable (Flame-resistant, 2 Conductor cross section: 0.5 mm , Insulator diameter: 2 Conductor cross section: 0.5 mm , Insulator 1.9 mm), Standard length: 300 mm diameter: 1.9 mm), Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) *2. Operation indicator (red), Setting indicator (green) Standard Models E2EQ-X3D1-M1(T)GJ 38 *1. 6-dia. vinyl-insulated round cable (flame-resistant), Standard length: 300 mm 21 dia. 27.6 *2. Operation indicator (red), Setting indicator (green) 17 24 5 Indicators *2 *1 M12 × 1 M12 1 4 × Two clamping nuts (fluororesin coated) (aluminum) Two toothed washers E2EQ-X7D1-M1(T)GJ E2EQ-X10D1-M1(T)GJ 56 *1. 6-dia. vinyl-insulated round cable *1. 6-dia. vinyl-insulated round cable (flame- (flame-resistant), Standard 47 42 dia. 42 resistant), Standard length: 300 mm length: 300 mm *2. Operation indicator (red), Setting 36 29 dia. 32 38 *2. Operation indicator (red), Setting indicator (green) 24 29 10 indicator (green) 6 M12 × 1 (aluminum) M12 × 1 (aluminum) *1 *1 Indicators*2 Indicators *2 Two clamping nuts (fluororesin coated) M18 × 1 4 Two clamping nuts (fluororesin coated) M30 × 1.5 5 Two toothed washers Two toothed washers Mounting Hole Dimensions E2EQ-X4X@ E2EQ-X8X@ E2EQ-X15X@ Model E2EQ-X3@ E2EQ-X7@ E2EQ-X10@ +0.5 +0.5 +0.5 F (mm) 12.5 dia. 18.5 dia. 30.5 dia. 0 0 0 F 8 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2015.1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2015 All Right Reserved.