Proximity Sensor with All-stainless Housing E2FM CSM_E2FM_DS_E_4_8 Highly Durable Proximity Sensor for Tough Environments • Completely stainless-steel housing • Aluminum chip immunity • Embedding installation to metal (steel) fittings • Chemical resistance certified by Ecolab Europe • Lineup includes pre-wire models and DC 3-wire NPN output models with fluororesin coating. Be sure to read Safety Precautions on page 9. For the most recent information on models that have been certified for Note: Models with a fluororesin coating also use vinyl chloride for the cable material safety standards, refer to your OMRON website. and require separate protection. Features One-piece completely stainless-steel housing with a face thickness of 0.8 mm The face thickness is approximately 4 times that of previous models (E2ES) to enable sensing in even more 0.8 mm severe conditions than ever. Brush Test Continuous Impact Test Chemical and Detergent Proof The one-piece completely stainless- steel housing of the sensing section withstands the following chemicals better. • Sodium chloride • Gasoline After 3 Minutes • Dilute sodium hydroxide • Dilute hydrochloric acid • Mineral oil • Barium hydroxide E2ES E2FM Any many others The E2FM was The E2ES with a top wall thickness not penetrated Note: Cannot be used for explosion-proof after 250,000 of 0.2 mm was applications. penetrated after impacts (depth: E2FM E2EQ 0.26 mm). 10,000 impacts. (Spatter-resistant) More than 20 times the The stainless-steel head durability of the E2ES! means almost no wear when cleaned with a metal brush. 1 E2FM Built-in Chip Immunity Chip immunity performance has been provided to greatly reduce false signals caused by spatter accumulation and other causes, almost eliminating the needs for cleaning, e.g., with metal brushes. Flush Mounting Extension distance Not influenced by surrounding installation environment. E2ES E2FM Note: When mounted in steel. Main Performance Comparison to Previous OMRON Products Face thickness Sensing distance Response frequency Ambient operating temperature E2FM E2ES E2FM E2ES E2FM E2ES E2FM E2ES M8 0.4 mm --- M8 1.5 mm --- M8 200 Hz --- −25 to 70°C 0 to 50°C M12 0.8 mm --- M12 2.0 mm --- M12 100 Hz --- M18 0.8 mm 0.2 mm M18 5.0 mm 4.0 mm M18 100 Hz 12 Hz M30 0.8 mm 0.2 mm M30 10.0 mm 8.0 mm M30 50 Hz 8 Hz The chemical resistance has been certified by Ecolab Europe Ecolab GmbH & Co. OHG This certificate is based on: P.O. Box 13 04 06 D-40551 Düsseldorf documented test procedures (test no.: F&E/P3-E Nr. 40-1) according to material resistance defined product descriptions certifies that for standardized cleaning procedure Test procedure Ecolab-test F&E Nr. 40-1 Product specifications: OMRON Manufacturing of Germany GmbH Carl-Benz-Strasse 4 Dipping test: P3-topax 56: 71154 Nufringen Complete immersion in solutions/liquid Acid foam cleaning substance for food and beverage industry Test period: P3-topax 66: 14 days Alkaline foam cleaning detergent with active material resistance tests Temperature: chlorine for machine cleaning in food and beverage industry room temperature (constant) P3-topax 91: Analysis: were performed with cleaning substances P3-topax 56, P3-topax 66, P3-topax 91 and Visual judgement like swelling, brittleness, Neutral disinfection agent based on demineralized water as a zero reference factor. discoloring quaternary ammonium compounds (QAV) for the food industry compared to zero-reference factor The material resistance of the tested series (demineralized water) Photometric documentation Inductive Proximity Sensor E2FM to the P3 products used in the test can be considered to be positive according to the cleaning procedure mentioned overleaf. Cleaning plan for food and beverage industry* Rinsing with water 40 – 50°C Düsseldorf, 14th February 2006 Rinsing with low pressure. Rinsing from top to bottom in the direction of the drains. Cleaning of the drains. Foaming from bottom to top Ecolab GmbH & Co. OHG alkaline: P3-topax 66 2 – 5 % daily acid: P3-topax 56 2 % on demand i.V. i. V. temperature: cold up to 40°C contact time: 15 min. recommended Thomas Tyborski Reimund Laaff Rinsing with water 40 – 50°C Rinsing from top to bottom with low pressure Spray disinfection P3-topax 91 1-2 %, 30 -60 minutes *short description 2 Workpiece Workpiece E2FM Ordering Information Sensors [Refer to Dimensions on page 10.] DC 2-Wire, Pre-wired Models Size Sensing distance Output Operation mode Model M8 E2FM-X1R5D1 2M * 1.5 mm Shielded M12 E2FM-X2D1 2M * 2 mm DC 2-Wire NO (polarity) M18 E2FM-X5D1 2M * 5 mm M30 E2FM-X10D1 2M * 10 mm Note: Models with NC operation are also available. Ask your OMRON representative for details. * Fluororesin-coated models are also available. The model numbers are E2FM-QX@D1. The cable material, however, is vinyl chloride and requires separate protection. DC 2-wire Pre-wired Smartclick Connector Models (M12) Size Sensing distance Output Operation mode Model M8 Polarity Pin allocations: 1-4 E2FM-X1R5D1-M1TGJ 0.3M 1.5 mm Polarity Pin allocations: 1-4 E2FM-X2D1-M1TGJ 0.3M M12 2 mm Shielded No polarity Pin allocations: 3-4 E2FM-X2D1-M1TGJ-T 0.3M Polarity Pin allocations: 1-4 NO E2FM-X5D1-M1TGJ 0.3M M18 5 mm No polarity Pin allocations: 3-4 E2FM-X5D1-M1TGJ-T 0.3M Polarity Pin allocations: 1-4 E2FM-X10D1-M1TGJ 0.3M M30 10 mm No polarity Pin allocations: 3-4 E2FM-X10D1-M1TGJ-T 0.3M DC 3-Wire, Pre-wired Models Model Size Sensing distance Output configuration: NPN NO Output configuration: PNP NO M8 E2FM-X1R5C1 2M E2FM-X1R5B1 2M Shielded 1.5 mm M12 E2FM-X2C1 2M E2FM-X2B1 2M 2 mm M18 E2FM-X5C1 2M E2FM-X5B1 2M 5 mm M30 E2FM-X10C1 2M E2FM-X10B1 2M 10 mm Note: Models with NC operation are also available. Ask your OMRON representative for details. DC 3-Wire, M12 Connector Models Model Size Sensing distance Output configuration: NPN NO Output configuration: PNP NO M8 E2FM-X1R5C1-M1 E2FM-X1R5B1-M1 * 1.5 mm Shielded M12 E2FM-X2C1-M1 E2FM-X2B1-M1 * 2 mm M18 E2FM-X5C1-M1 E2FM-X5B1-M1 * 5 mm M30 E2FM-X10C1-M1 E2FM-X10B1-M1 * 10 mm * Fluororesin-coated models are also available. The model numbers are E2FM-QX@B1-M1. The cable material, however, is vinyl chloride and requires separate protection. 3 E2FM Accessories (Order Separately) Sensor I/O Connectors (M12, Sockets on One Cable End) (Models for Connectors and with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) [Refer to XS2, XS5.] Appearance Cable length Sensor I/O Connector model number Applicable Proximity Sensor model number Straight 2m XS2F-D421-DC0-F 5m XS2F-D421-GC0-F E2FM-X@C1-M1 E2FM-X@B1-M1 L-shape 2m XS2F-D422-DC0-F 5m XS2F-D422-GC0-F Smartclick 2m XS5F-D421-D80-F Connector Relay E2FM-X@D1-M1TGJ Models (M12) E2FM-X@D1-M1TGJ-T 5m XS5F-D421-G80-F Note: Refer to Introduction to Sensor I/O Connectors for details. Ratings and Specifications DC 2-Wire (E2FM-X@D@) Size M8 M12 M18 M30 M12 M18 M30 Shielded Shielded E2FM-X2D1- E2FM-X5D1- E2FM-X10D1- Model E2FM-X1R5D1-@ E2FM-X2D1-@ E2FM-X5D1-@ E2FM-X10D1-@ Item M1T1GJ-T M1T1GJ-T M1T1GJ-T Sensing distance 1.5 mm±10% 2 mm±10% 5 mm±10% 10 mm±10% 2 mm±10% 5 mm±10% 10 mm±10% Set distance 0 to 1.05 mm 0 to 1.4 mm 0 to 3.5 mm 0 to 7 mm 0 to 1.4 mm 0 to 3.5 mm 0 to 7 mm Differential travel 15% max. of sensing distance Sensing object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 7.) Iron, Iron, Iron, Iron, Iron, Iron, Iron, Standard sensing object 8 × 8 × 1 mm 12 × 12 × 1 mm 30 × 30 × 1 mm 54 × 54 × 1 mm 12 × 12 × 1 mm 30 × 30 × 1 mm 54 × 54 × 1 mm Response frequency *1 200 Hz 100 Hz 100 Hz 50 Hz 100 Hz 100 Hz 50 Hz Power supply voltage 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. (operating voltage range) Leakage current 0.8 mA max. Output configuration With polarity No polarity Switching 3 to 100 mA capacity Control output Residual 3 V max. 5 V max. voltage (Load current: 100 mA max., Cable length: 2 m) (Load current: 100 mA max., Cable length: 2 m) Indicators Operation indicator (red LED), Setting/Operation indicator (green LED) Operation mode (with sensing object NO *2 approaching) Protection circuits Surge suppressor, Load short-circuit protection Ambient temperature range Operating/Storage: −25 to 70°C (with no icing or condensation) Ambient humidity range Operating/Storage: 35% to 95% (with no condensation) Temperature influence ±20% max. of sensing distance at 23°C in the temperature range of −25 to 70°C. Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Destruction: 2 500 m/s 2 Shock resistance 10 times each Destruction: 1,000 m/s 10 times each in X, Y, and Z directions in X, Y, and Z directions Degree of protection IEC 60529 IP67 Unmarked: Pre-wired Models (Standard cable length: 2 m) Connection method Models ending with -M1GJ-@: Pre-wired Connector Models (Standard cable length: 300 mm) 4 E2FM Size M8 M12 M18 M30 M12 M18 M30 Shielded Shielded E2FM-X2D1- E2FM-X5D1- E2FM-X10D1- Model E2FM-X1R5D1-@ E2FM-X2D1-@ E2FM-X5D1-@ E2FM-X10D1-@ Item M1T1GJ-T M1T1GJ-T M1T1GJ-T Pre-wired Approx. 105 g Approx. 190 g Approx. 215 g Approx. 295 g --- --- --- Models (2 m) Weight (packed Pre-wired state) Connector Approx. 65 g Approx. 85 g Approx. 110 g Approx. 190 g Approx. 85 g Approx. 110 g Approx. 190 g Models Case Stainless steel (SUS303) Sensing Stainless steel (SUS303) surface (thickness) (0.4 mm) (0.8 mm) (0.8 mm) Materi- Clamping als Stainless steel (SUS303) nuts Cable PVC (flame retardant) Toothed Zinc-plated iron washer Accessories Instruction manual *1. The response frequency of the DC switching section is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. *2. NC (normally closed) models are also available. Contact your OMRON representative. 5 E2FM DC 3-Wire (E2FM-X@C@, E2FM-X@B@) Size M8 M12 M18 M30 Shielded Shielded Item Model E2FM-X1R5@ E2FM-X2@ E2FM-X5@ E2FM-X10@ Sensing distance 1.5 mm±10% 2 mm±10% 5 mm±10% 10 mm±10% Set distance 0 to 1.05 mm 0 to 1.4 mm 0 to 3.5 mm 0 to 7 mm Differential travel 15% max. of sensing distance Sensing object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 7.) Standard sensing object Iron, 8 × 8 × 1 mm Iron, 12 × 12 × 1 mm Iron, 30 × 30 × 1 mm Iron, 54 × 54 × 1 mm Response frequency *1 200 Hz 100 Hz 100 Hz 50 Hz Power supply voltage (operating voltage 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. range) Current consumption 10 mA max. Output configuration PNP open collector output Switching ca- 200 mA max. pacity Control output Residual 2 V max. (Load current: 200 mA, Cable length: 2 m) voltage Indicators Operation indicator (yellow LED) Operation mode C1 Models: NPN open collector, NO (normally open) *2 (with sensing object B1 Models: PNP open collector, NO (normally open) *2 approaching) Reversed power supply polarity protection, Surge suppressor, Load short-circuit protection, and Reversed output po- Protection circuits larity protection (except the E2FM-X1R5B1-M1) Ambient temperature Operating/Storage: −25 to 70°C (with no icing or condensation) range Ambient humidity range Operating/Storage: 35% to 95% (with no condensation) Temperature ±20% max. of sensing distance at 23°C in the temperature range of −25 to 70°C. influence ±1% max. of sensing distance in the rated voltage ±15% range (using the sensing distance at the rated voltage as Voltage influence standard) Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions 2 Destruction: 500 m/s 2 Shock resistance 10 times each in X, Y, and Z Destruction: 1,000 m/s 10 times each in X, Y, and Z directions directions Degree of protection IEC 60529 IP67 Unmarked: Pre-wired Models (Standard cable length: 2 m) Connection method Models ending with -M1: Connector Models Pre-wired --- Approx. 170 g Approx. 190 g Approx. 275 g Models (2 m) Weight (packed Pre-wired state) Connector Approx. 45 g Approx. 55 g Approx. 75 g Approx. 160 g Models Case Stainless steel (SUS303) Sensing sur- Stainless steel (SUS303) face Materi- (thickness) (0.4 mm) (0.8 mm) als Clamping Stainless steel (SUS303) nuts Toothed Zinc-plated iron washer Accessories Instruction manual *1. The response frequency of the DC switching section is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. *2. NC (normally closed) models are also available. Contact your OMRON representative. 6 E2FM Engineering Data (Reference Value) Sensing Area Influence of Sensing Object Size and Material E2FM-X@ E2FM-X1R5@ E2FM-X2@ 12 2.5 3.0 E2FM-X10@ 10 2.5 2.0 Iron 8 Iron 2.0 1.5 E2FM-X5@ 6 1.5 1.0 Stainless Stainless 4 1.0 E2FM-X2D@ steel E2FM-X1R5@ steel (SUS304) (SUS304) Aluminum Brass 0.5 Brass 2 0.5 Aluminum Copper Copper 0 0.0 0.0 −25 −20 −15 −10 −50 5 10 15 20 25 0 5 10 15 20 25 01 501520253035 Distance Y (mm) Side length of sensing object: d (mm) Side length of sensing object: d (mm) Leakage Current E2FM-X5@ E2FM-X10@ E2FM-X@D1-M1TGJ (-T) 7 12 1.0 Iron 6 10 E2FM-X1R5D1-@ 0.8 Iron 5 E2FM-X10D1-M1TGJ(-T) 8 0.6 Stainless 4 steel 6 (SUS304) 3 Stainless E2FM-X5D1-M1GJ(-T) 0.4 steel 4 E2FM-X2D1-M1TGJ(-T) (SUS304) Brass 2 Brass 0.2 2 1 Aluminum Aluminum Copper Copper 0 0 0.0 0 10 203040 50 60 70 80 90 020 40 60 80 0 5 10 15 20 25 30 Side length of sensing object: d (mm) Side length of sensing object: d (mm) Power supply voltage (V) Residual Output Voltage E2FM-X@C@/B@ E2FM-X@D1-M1TGJ (-T) 5 2 4 E2FM-X@D1-M1TGJ-T 1.5 3 E2FM-X2@ E2FM-X5@ E2FM-X@D1-@ 1 E2FM-X10@ 2 0.5 1 E2FM-X1R5@ 0 0 1 3 5 1 0 30 50 100 1 10 50 100 200 1,000 Load current (mA) Load current (mA) 7 Distance X (mm) Residual output voltage (V) Distance X (mm) Distance X (mm) Distance X (mm) Residual output voltage (V) Distance X (mm) Leakage current (mA) E2FM I/O Circuit Diagrams DC 2-Wire Models Operation Model Timing chart Output circuit mode Brown Connector Pin Load Arrangement 1 12 to 24 VDC Proximity Set position sensor Unstable E2FM- main sensing Stable sensing circuit X@D1-@ Non-sensing area area area Blue 4 Proximity sensor 0 V Note: Pins 2 and 3 Sensing object are not used. Note: The load can be connected to either the +V or 0 V side. (%) 100 70 (TYP) 0 NO Rated Connector Pin sensing 4 Load Arrangement distance Setting ON 12 to 24VDC indicator Proximity OFF (green) sensor main Operation ON circuit E2FM- indicator (red) OFF X@D1- 3 Note: Pins 1 and 2 are 0V M1TGJ-T ON Control not used. output OFF Note1. The load can be connected to either the +V or 0 V side. 2. The E2FM-X@@1-M1TGJ-T has no polarity. There is no need to be concerned about the polarity of pins 3 and 4. DC 3-Wire Models Opera- Output tion config- Model Timing chart Output circuit mode uration Brown E2FM- +V Connector Pin X1R5C@ Arrangement Load Proximity NPN E2FM- Non-sensing area Sensing area sensor * main open- X2C@ Black circuit Proximity sensor collector E2FM- Sensing object model X5C@ Blue Note: For Connector Models, the connection between pins 1, 4 and 3 E2FM- 0 V uses an NO contact, and the (%) 100 0 X10C@ connection between pins 1, 2 and 3 * There is no reversed output polarity protection diode. uses an NC contact. NO Rated Brown sensing E2FM- DC12 to 24VDC Connector Pin distance X1R5B@ Arrangement Operation ON Proximity PNP E2FM- indicator Black sensor * (yellow) main open- X2B@ OFF circuit ON collector E2FM- Control Load output model X5B@ OFF Note: For Connector Models, the connection between pins 1, 4 and 3 E2FM- Blue 0 V uses an NO contact, and the X10B@ connection between pins 1, 2 and 3 * There is no reversed output polarity protection diode. uses an NC contact. 8 E2FM Safety Precautions (Unit: mm) WARNING Item This product is not designed or rated for ensuring l d D m n Embedding Model safety of persons. Do not use it for such purposes. material Iron 0 8 0 4.5 30 E2FM-X1R5@ Aluminum 10 50 10 4.5 50 Never use this product with an AC power supply. Otherwise, explosion may result. Iron 0 12 0 840 E2FM-X2@ Aluminum 16 70 16 8 70 Iron 0 18020 60 Precautions for Safe Use E2FM-X5@ Aluminum 16 80 16 20 80 The following precautions must be observed to ensure safe operation. Iron 0 30040 100 1. Do not use the Sensor in an environment where inflammable or E2FM-X10@ explosive gas is present. Aluminum 24 120 24 40 120 2. Do not attempt to disassemble, repair, or modify any Sensors. Note: The influence from other non-magnetic surrounding metals is nearly the 3. Power Supply Voltage same as that from aluminum. Do not use a voltage that exceeds the rated operating voltage range. Applying a voltage that is higher than the operating voltage Mutual Interference range may result in explosion or fire. When installing two or more Sensors face-to-face or side-by-side, 4. Incorrect Wiring ensure that the minimum distances given in the following table are Be sure that the power supply polarity and other wiring is correct. maintained. Incorrect wiring may cause explosion or fire. (Unit: mm) 5. Connection without a Load If the power supply is connected directly without a load, the internal Model Item A B elements may explode or burn. Be sure to insert a load when E2FM-X1R5@ 35 30 connecting the power supply. A E2FM-X2@ 40 35 Precautions for Correct Use E2FM-X5@ 65 60 B E2FM-X10@ 110 100 Do not use the Sensor under ambient conditions that exceed the ratings. 1. Do not use the Sensor in the following locations. Chips from Cutting Aluminum (1) Outdoor locations directly subject to sunlight, rain, snow, or Normally, chips from cutting aluminum or cast iron will not cause a water droplets detection signal to be output even if it adheres to or accumulates on (2) Locations subject to atmospheres with chemical vapors, in the detection surface. In the following cases, however, a detection particular solvents and acids signal may be output. Remove the cutting chips in these cases. (3) Locations subject to corrosive gas 2. The Sensor may malfunction if used near ultrasonic cleaning 2 equipment, high-frequency equipment, transceivers, cellular d 1. If d ≥ D at the center of the detection 3 phones, inverters, or other devices that generate a high-frequency surface where d is the cutting chip size Cutting chip electric field. Refer to the Technical Guide Photoelectric Sensors and D is the detection surface size for typical measures. Detection surface D Dimension 3. Laying the Sensor wiring in the same conduit or duct as high- Model D (mm) voltage wires or power lines may result in incorrect operation and E2FM-X1R5@ 6 damage due to induction. Wire the Sensor using a separate E2FM-X2@ 10 conduit or independent conduit. E2FM-X5@ 16 4. Cleaning Never use thinner or other solvents. Otherwise, the Sensor surface E2FM-X10@ 28 may be dissolved. Pressed down 2. If the cutting chips are pressed down Cutting chips ● Design Influence of Surrounding Metal When the Proximity Sensor is embedded in metal, make sure that the clearances given in the following table are maintained. The values depend on the type of nuts used for mounting. Be sure to use the supplied nuts (SUS303). ● Mounting Do not tighten the nut with excessive force. A washer must be used d dia. with the nut. Do not use tightening force that exceeds the values in the n m following table. D l l Model Torque E2FM-X1R5@ 9 N·m E2FM-X2@ 30 N·m E2FM-X5@ 70 N·m E2FM-X10@ 180 N·m 9 Toothed washer Toothed washer Toothed washer Toothed washer Toothed washer Toothed washer Toothed washer Toothed washer E2FM (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified. Sensors Pre-wired Models E2FM-X1R5@ E2FM-X2@ 53 49 39 30 33 25 4-dia. vinyl-insulated round cable (flame 7 21 dia. 6-dia. vinyl-insulated round cable (flame 4 15 dia. retardant), Standard length; 2 m * 45 retardant), Standard length; 2 m * Two clamping Two clamping M8 × 1 nuts 13 Operation indicators M12 × 1 Operation indicators nuts 17 * 4-dia. vinyl-insulated round cable with 2 conductors 2 * 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.2 mm , Insulator diameter: 1.4 mm) 2 (Conductor cross section: 0.5 mm , Insulator diameter: 1.75 mm) 4-dia. vinyl-insulated round cable with 3 conductors 2 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm , Insulator diameter: 1.2 mm) 2 (Conductor cross section: 0.5 mm , Insulator diameter: 1.75 mm) E2FM-X10@ E2FM-X5@ 63.5 49 43 10 42 dia. 56 5 42 36 10 6-dia. vinyl-insulated round cable (flame 29 dia. 4 retardant), Standard length; 2 m * 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 2 m * Operation indicators Two clamping 36 M30 ´ 1.5 M18 ´ 1 nuts Operation indicators Two clamping 24 nuts * 6-dia. vinyl-insulated round cable with 2 conductors * 6-dia. vinyl-insulated round cable with 2 conductors 2 2 (Conductor cross section: 0.5 mm , Insulator diameter: 1.75 mm) (Conductor cross section: 0.5 mm , Insulator diameter: 1.75 mm) 6-dia. vinyl-insulated round cable with 3 conductors 6-dia. vinyl-insulated round cable with 3 conductors 2 2 (Conductor cross section: 0.5 mm , Insulator diameter: 1.75 mm) (Conductor cross section: 0.5 mm , Insulator diameter: 1.75 mm) Pre-wired Connector Models E2FM-X1R5D@-M1TGJ-@ E2FM-X2D@-M1TGJ-@ 53 49 39 30 25 M12 × 1 33 M12 ´ 1 7 15 dia. 45 21 dia. 4 Two clamping M8 × 1 nuts Two 13 Indicator *2 *1 clamping nuts M12 ´ 1 17 *1 Indicator *2 *1. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 300 mm *1. 4-dia. vinyl-insulated round cable (flame retardant), Standard length; 300 mm *2. Operation indicator (red/green) *2. Operation indicator (red/green) Setting indicator (green) Setting indicator (green) E2FM-X5D@-M1TGJ-@ E2FM-X10D@-M1TGJ-@ 63.5 49 56 43 42 10 42 dia. 5 36 10 M12 ´ 1 29 dia. 4 M12 ´ 1 Two clamping M18 ´ 1 nuts 24 Indicator *2 *1 Two clamping 36 M30 ´ 1.5 *1 nuts Indicator *2 *1. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 300 mm *2. Operation indicator (red/green) *1. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 300 mm Setting indicator (green) *2. Operation indicator (red/green) Setting indicator (green) 10 Toothed washer Toothed washer oothed washer T Toothed washer E2FM M12 Connector Models E2FM-X1R5@@-M1 E2FM-X2@@-M1 53.5 53 34.5 39 30 33 21 dia. 25 4 7 5 15 dia. 4 Two clamping Two clamping M8 × 1 M12 × 1 17 M12 × 1 M12 × 1 13 nuts nuts Four operation indicators (yellow) Four operation indicators (yellow) E2FM-X5@@-M1 E2FM-X10@@-M1 63.5 49 56 43 10 42 42 dia. 5 36 29 dia. 10 4 M12 × 1 Two clamping M12 × 1 24 M18 × 1 nuts Four operation indicators (yellow) Two clamping M30 × 1.5 Four operation indicators (yellow) 36 nuts Mounting Hole Dimensions Dimension M8 M12 M18 M30 +0.5 +0.5 +0.5 +0.5 F (mm) 8.5 dia. 12.5 dia. 18.5 dia. 30.5 dia. 0 0 0 0 F 11 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2017.2 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2017 All Right Reserved.