Chemical Resistant Inductive Proximity Sensor E2FQ Fluoro plastic housing for highest chemical and detergent resistance Ordering Information DC 3-wire models DC 2-wire models Shape Sensing distance Response Response PNP (NO) NPN (NO) NO frequency frequency E2FQ-X2F1 E2FQ-X2E1 1.5 kHZ E2FQ-X2D1 800 Hz 2mm M12 Shielded E2FQ-X5F1 E2FQ-X5E1 600 Hz E2FQ-X5D1 500 Hz 5mm M18 E2FQ-X10F1 E2FQ-X10E1 400 Hz E2FQ-X10D1 300 Hz 10mm M30 Characteristic data (typical) Sensing Distance vs. Sensing Object . E2FQ-X2# E2FQ-X5# E2FQ-X10# 2.4 7 12 #d 2.2 #d 11 #d t=1mm Mild steel t=1mm t=1mm Mild steel X 6 X X 2 10 Mild steel 1.8 9 Stainless steel 5 (SUS304) 1.6 8 Stainless steel 1.4 7 4 Stainless steel (SUS304) 1.2 (SUS304) 6 1 3 5 Brass Brass Brass 0.8 4 2 0.6 3 Aluminum Aluminum Aluminum 0.4 2 1 1 0.2 0 5 10 15 20 25 0 5 10 15 20 25 30 35 40 50 0 102030405060 Side length of sensing object d (mm) Side length of sensing object d (mm) Side length of sensing object d (mm) E2FQ 1 Sensing distance X (mm) Sensing distance X (mm) Sensing distance X (mm) Rating/Performance Item Model E2FQ-X2@ E2FQ-X5@ E2FQ-X10@ Sensing distance 2 mm ±10% 5 mm ±10% 10 mm ±10% Setting distance 0 to 1.6 mm 0 to 4 mm 0 to 8 mm Differential distance E1, F1 models: 10% max. of sensing distance Sensing object Ferrous metal (Sensitivity lowers with non-ferrous metals) Standard sensing object 12 x 12 x 1 mm 18 x 18 x 1 mm 30 x 30 x 1 mm (mild steel) E1, F1 models: 1.5 kHz E1, F1 models: 600 Hz, E1, F1 models: 400 Hz, Response frequency*1 D1 models: 800 Hz D1 models: 500 Hz D1 models: 300 Hz Power supply E1, F1 models: 12 to 24 VDC, ripple (p-p) : 10% max., (10 to 30 VDC) (Operating voltage D1 models: 12 to 24 VDC, ripple (p-p) : 20% max., (10 to 36 VDC) range) Current consumption E1, F1 models: 17 mA max. Leakage current D1 models: 0.8 mA max. Switching E1, F1 models: 200 mA max., D1 models: 5 to 100 mA DC capacity Control output Residual E1, F1 models: 2 V max. (load current: 200 mA with cable length: 2 m) voltage D1 models: 3.0 V max. (under load current of 100 mA with cable length of 2 m) E models: operation indicator (red) Indicator lamp D models: operation indicator (green for stable detection, red for detection close to threshold) Operating status (with sensing object Normally open (NO) approaching) Protective circuits E1, F1 models: Protection for reverse polarity, load short circuit, surge voltage Ambient temperature Operating/Storage: -25°C to 70°C (with no icing or condensation) Ambient humidity Operating/Storage: 35% to 95%RH (with no condensation) Temperature influence 10% max. of sensing distance at 23°C within temperature range of -25°C to 70°C Voltage influence E1, F1 models: ±2.5% max. of sensing distance within rated voltage range ±15% Insulation resistance 50 MW min. (at 500 VDC) between energized parts and case Dielectric strength E1, F1, D1 models: 1,000 VAC 50/60 Hz for 1 min between energized parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions 2 Destruction: 500 m/s for 10 times 2 Shock resistance Destruction: 1,000 m/s for 10 times each in X, Y, and Z directions each in X, Y, and Z directions Protective structure IEC60529 IP67 Connection method Pre-wired models (standard length: 2 m) Weight (Packed state) Approx. 70 g Approx. 130 g Approx. 170 g Case Material Fluoro plastic Sensing surface Accessories Instruction manual *1. The response frequencies are average values measured on condition that the distance between each sensing object is twice as large as the size of the sensing object and the sensing distance set is half of the maximum sensing distance. 2 Inductive Sensors Output Circuit Diagram Operating Output Model Timing chart Output circuit status specifications Brown Yes Sensing +V object No Load Operates (between black Black and blue leads) Releases Main PNP E2FQ-X@F1 Output voltage H circuit 2.2W Output (between black and blue leads) L Load 4.7kW ON Operation 100W indicator Blue OFF 0V Brown +V 100W (see note 1) Yes Sensing Load object 4.7kW No Black Main Load Operates circuit (between black 2.2W Output and blue leads) Releases Tr NPN E2FQ-X@E1 Output voltage (see note 2) H (between black NO and blue leads) L Blue 0V ON Operation indicator OFF Note: 1. 200 mA max.(load current) 2. When a transistor is connected Brown Load +V Yes Sensing Main object No circuit Operates DC 2-wire E2FQ-X@D1 Load Releases Blue ON 0V Operation indicator OFF Note: The load can be connected to either the +V or the 0-V line. Precautions Mutual Interference (Unit: mm) Correct Use Item Model A B Design A E2FQ-X2# 30 20 Effects of Surrounding Metal E2FQ-X5# 50 35 Provide a minimum distance between the Sensor and the E2FQ-X10# 100 70 B surrounding metal as shown in the table below. l Installation Do not tighten the nut with excessive force. A washer must be used with the nut. n d dia. m D m l Effects of Surrounding Metal (Unit: mm) Note: The table below shows the value of tightening torques when using Item toothed washers. Model l d D m n E2FQ-X2# Torque Tensile strength 12 818 Model (torque) E2FQ-X5# 0 18 0 20 27 E2FQ-X2# 0.98 Nm E2FQ-X10# 30 40 45 E2FQ-X5# 2 Nm E2FQ-X10# Mutual Interference Others If more than one Proximity Sensor is installed face to face or Chemical resistance in parallel, ensure that the distances between two Units adja- cent to each other are the same as or larger than the corre- sponding values shown in the following table. E2FQ 3 Dimensions (Unit: mm) E2FQ-X2E1 E2FQ-X2D1 E2FQ-X2F1 38 38 21 dia. 27 21 dia. 27 17 24 17 24 (see note) (see note) Indicator Indicator M12 x 1 Two, clamping nut Two, clamping nut M12 x 1 6 6 Two, Toothed washers Two, Toothed washers Note: Note: Oil-resistant, vibration-resistant, and fire-retardant Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated round cord, 6 dia. x 2 cores, vinyl-insulated round cord, 6 dia. x 3 cores, standard length: 2 m standard length: 2 m The cord can be extended in an independent conduit The cord can be extended in an independent conduit for 200 m maximum. for 200 m maximum. E2FQ-X5D1 E2FQ-X5E1 E2FQ-X5F1 47 47 40 40 29 dia. 32 29 dia. 32 24 29 24 29 (see note) (see note) Indicator Indicator M18 x 1 8 Two, clamping nut M18 x 1 8 Two, clamping nut Two, Toothed washers Two, Toothed washers Note: Oil-resistant, vibration-resistant, and fire-retardant Note: vinyl-insulated round cord, 6 dia. x 3 cores, Oil-resistant, vibration-resistant, and fire-retardant standard length: 2 m vinyl-insulated round cord, 6 dia. x 2 cores, standard length: 2 m The cord can be extended in an independent conduit for 200 m maximum. The cord can be extended in an independent conduit for 200 m maximum. E2FQ-X10E1 E2FQ-X10D1 E2FQ-X10F1 57 57 50 50 42 dia. 41 42 dia. 41 36 38 36 38 (see note) (see note) Indicator Indicator M30 x 1.5 Two, clamping nut 8 M30 x 1.5 Two, clamping nut 8 Two, Toothed washers Two, Toothed washers Note: Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated Note: round cord, 6 dia. x 3 cores, standard length: 2 m Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated The cord can be extended in an independent conduit for 200 m maximum. round cord, 6 dia. x 2 cores, standard length: 2 m The cord can be extended in an independent conduit for 200 m maximum. Mounting Holes Model F (mm) +0.5 E2FQ-X2# 12.5 mm dia. 0 +0.5 E2FQ-X5# 18.5 mm dia. 0 +0.5 E2FQ-X10# 30.5 mm dia. 0 F 4 Inductive Sensors E2FQ 5 WARRANTY • Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this OMRON’s exclusive warranty is that the products are free from de- document. fects in materials and workmanship for a period of one year (or other • Nuclear energy control systems, combustion systems, railroad sys- period if specified) from date of sale by OMRON. tems, aviation systems, medical equipment, amusement machines, OMRON MAKES NO WARRANTY OR REPRESENTATION, EX- vehicles, safety equipment, and installations subject to separate in- PRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MER- dustry or government regulations. CHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF • Systems, machines, and equipment that could present a risk to life THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT or property. THE BUYER OR USER ALONE HAS DETERMINED THAT THE Please know and observe all prohibitions of use applicable to the PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF products. THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WAR- RANTIES, EXPRESS OR IMPLIED. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING LIMITATIONS OF LIABILITY THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDI- ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS RECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PROPERLY RATED AND INSTALLED FOR THE INTENDED USE COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, PERFORMANCE DATA WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of OMRON for any act exceed the in- Performance data given in this document is provided as a guide for dividual price of the product on which liability is asserted. the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRAN- must correlate it to actual application requirements. Actual perfor- TY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS mance is subject to the OMRON Warranty and Limitations of Liability. UNLESS OMRON’S ANALYSIS CONFIRMS THAT THE PROD- UCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND CHANGE IN SPECIFICATIONS MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Product specifications and accessories may be changed at any time based on improvements and other reasons. SUITABILITY FOR USE It is our practice to change model numbers when published ratings or THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT features are changed, or when significant construction changes are SAFETY RATED. THEY ARE NOT DESIGNED OR RATED FOR EN- made. However, some specifications of the product may be changed SURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED without any notice. When in doubt, special model numbers may be as- UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE signed to fix or establish key specifications for your application on FOR SUCH PURPOSES. Please refer to separate catalogs for OM- your request. Please consult with your OMRON representative at any RON's safety rated products. time to confirm actual specifications of purchased products. OMRON shall not be responsible for conformity with any standards, DIMENSIONS AND WEIGHTS codes, or regulations that apply to the combination of products in the customer’s application or use of the product. Dimensions and weights are nominal and are not to be used for man- ufacturing purposes, even when tolerances are shown. At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that ERRORS AND OMISSIONS apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combina- The information in this document has been carefully checked and is tion with the end product, machine, system, or other application or believed to be accurate; however, no responsibility is assumed for use. clerical, typographical, or proofreading errors, or omissions. The following are some examples of applications for which particular PROGRAMMABLE PRODUCTS attention must be given. This is not intended to be an exhaustive list OMRON shall not be responsible for the user’s programming of a pro- of all possible uses of the products, nor is it intended to imply that the grammable product, or any consequence thereof. uses listed may be suitable for the products: Cat. No. D029-E2-05A-X In the interest of product improvement, specifications are subject to change without notice. OMRON EUROPE B.V. Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands Phone: +31 23 568 13 00 Fax: +31 23 568 13 88 www.industrial.omron.eu 6 Inductive Sensors