Oil-resistant, Long-range Photoelectric Sensor with Metal Housing E3S-C CSM_E3S-C_DS_E_9_2 Water- and Oil-resistant Photoelectric Sensor with Metal Housing Used for Long- range Sensing • Excellent resistance against the water and oil. Easy application in locations with oil mist. Long-range sensing up to 30 m with Through-beam models. 2 Shock resistance rated at 1,000m/s . Product lineup includes metal M12 pre-wired connector models. NPN/PNP selector switch output. For the most recent information on models that have been certified for Be sure to read Safety Precautions on safety standards, refer to your OMRON website. page 7. Ordering Information Sensors (Refer to Dimensions on page 8.) Red light Infrared light Sensing method Appearance Connection method Sensing distance Model E3S-CT11 2M Pre-wired Emitter E3S-CT11-L 2M Horizontal Receiver E3S-CT11-D 2M E3S-CT11-M1J 0.3M Pre-wired Connector (M12) Emitter E3S-CT11-L-M1J 0.3M Receiver E3S-CT11-D-M1J 0.3M Through-beam 30 m (Emitter + Receiver) * E3S-CT61 2M Pre-wired Emitter E3S-CT61-L 2M Vertical Receiver E3S-CT61-D 2M E3S-CT61-M1J 0.3M Pre-wired Connector (M12) Emitter E3S-CT61-L-M1J 0.3M Receiver E3S-CT61-D-M1J 0.3M Pre-wired E3S-CR11 2M Horizontal Pre-wired Connector (M12) E3S-CR11-M1J 0.3M Retro-reflective 3 m Pre-wired E3S-CR61 2M Vertical Pre-wired Connector (M12) E3S-CR61-M1J 0.3M E3S-CD11 2M 700 mm Pre-wired E3S-CD12 2M 2 m Horizontal 700 mm E3S-CD11-M1J 0.3M Pre-wired Connector (M12) E3S-CD12-M1J 0.3M 2 m Diffuse-reflective E3S-CD61 2M 700 mm Pre-wired Vertical E3S-CD62 2M 2 m 700 mm E3S-CD61-M1J 0.3M Pre-wired Connector (M12) E3S-CD62-M1J 0.3M 2 m * Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver. 1 E3S-C Accessories (Order Separately) Slits (A Slit is not provided with Through-beam Sensors. Order a Slit separately if required.) (Refer to Dimensions on page 10.) Minimum detect- Sensing Slit width able object Model Quantity Remarks distance (reference value) 0.5 mm × 11 mm 1.8 m 0.5-mm dia. 1 set each for (Snap-in Long Slit) 1 mm × 11 mm 3.5 m 1-mm dia. Emitter and Re- E39-S61 Can be used with the E3S-CT@1(-M1J) ceiver 2 mm × 11 mm 7 m 2-mm dia. Through-beam Sensor. Refer to page 10. (8 Slits total) 4 mm × 11 mm 15 m 2.6-mm dia. Reflectors (A Reflector is required for each Retro-reflective Sensor.) The E39-R1 Reflector is provided with the Sensor. Order other Reflectors separately if required. (Refer to Dimensions on E39-L/E39-S/E39-R.) Sensing distance Name Model Quantity Remarks Rated value Reference value 3 m --- E39-R1 1 Provided with the E3S-CR@1 (-M1J) Retro-reflective Sensor. Reflectors --- 4 m E39-R2 1 --- --- 1.5 m E39-R3 1 --- Small Reflectors --- 750 mm E39-R4 1 --- --- 700 mm (50 mm)* E39-RS1 1 Tape Reflectors --- 1,100 mm (100 mm)* E39-RS2 1 Enables MSR function. --- 1,400 mm (100 mm)* E39-RS3 1 Note: 1. If you use any Reflector other than the enclosed Reflector, make sure that the stability indicator lights properly when you set the Sensor. 2. Refer to Reflectors on E39-L/E39-S/E39-R for details. * Values in parentheses indicate the minimum distance required between the Sensor and Reflector. Mounting Brackets Some Mounting Brackets are provided with the Sensor. Order other Mounting Brackets separately if required. (Refer to Dimensions on E39-L/E39-S/E39-R.) Appearance Model Quantity Remarks E39-L102 1 Provided with Horizontal Models. E39-L103 1 Provided with Vertical Models. Mounting bracket for changing from E3S- E39-L85 1 @@@@@42/44 to E3S-C Vertical Models. Mounting bracket for changing from E3S- E39-L86 1 @@@@@43 to E3S-C Vertical Models. E39-L87 1--- Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter. 2. Refer to Mounting Brackets on E39-L/F39-L/E39-S/E39-R for details. Sensor I/O Connectors (Sockets on One Cable End) (Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) (Refer to Dimensions on XS2.) Cable Appearance Cable type Model 2 m XS2F-D421-DC0-F Straight 5 m XS2F-D421-GC0-F Fire-retardant, 3-wire robot cable 2 m XS2F-D422-DC0-F L-shape 5 m XS2F-D422-GC0-F Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter. 2. For details on Sensor I/O Connectors and cables such as vibration-proof robot cables, refer to Introduction to Sensor I/O Connectors/Sensor Controllers. 2 E3S-C Ratings and Specifications Sensing Retro-reflective Through-beam Diffuse reflective method (with M.S.R. function) *1 Horizontal Horizontal Horizontal Horizontal E3S-CT11(-M1J) E3S-CR11(-M1J) E3S-CD11(-M1J) E3S-CD12(-M1J) Model Vertical Vertical Vertical Vertical Item E3S-CT61(-M1J) E3S-CR61(-M1J) E3S-CD61(-M1J) E3S-CD62(-M1J) 700 mm 2 m Sensing distance 30 m 3 m (when using E39-R1) (300 × 300 mm (300 × 300 mm white paper) white paper) Standard sensing Opaque, 15-mm dia. min. Opaque, 75-mm dia. min. --- object Differential travel --- 20% max. of sensing distance Emitter and Receiver: 3° Directional angle 3° to 10° --- to15° Light source Infrared LED (880 nm) Red LED (700 nm) Infrared LED (880 nm) (wavelength) Power supply voltage 10 to 30 VDC including 10% (p.p) ripple 50 mA max. (Emitter 25 mA Current consumption 40 mA max. max. Receiver 25 mA max.) Load power supply voltage: 30 VDC max. Load current: 100 mA max. (Residual voltage: NPN output: 1.2 V max., PNP output: 2.0 V max.) Control output Open controller output (NPN/PNP selectable) Light-ON/Dark-ON selectable Power supply reverse polari- Power supply reverse polarity protection, Output short-circuit protection, Protection circuits ty circuit protection, Output Mutual interference prevention short-circuit protection Response time Operate or reset: 1 ms max. Operate or reset 2 ms max. Sensitivity One-turn adjuster Two-turn endless adjuster with an indicator adjustment Ambient illumination Incandescent lamp: 5,000 lx max. (Receiver side) Sunlight: 10,000 lx max. Ambient temperature Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation) range Ambient humidity Operating: 35% to 85%, Storage: 35% to 95% (with no condensation) range Insulation resistance 20 MΩ min. (at 500 VDC) Dielectric strength 1,000 VAC, 50/60 Hz for 1 min 2 Vibration resistance Destruction: 10 to 2,000 Hz, 1.5-mm double amplitude or 300 m/s for 0.5 hours each in X, Y, and Z directions 2 Shock resistance Destruction: 1,000 m/s 3 times each in X, Y, and Z directions Degree of protection IEC 60529: IP67 (in-house standards: oil-resistant), NEMA: 6P (indoors only) *2 Connection method Pre-wired (standard cable length: 2 m) or Pre-wired M12 Connector (standard cable length: 0.3 m) Approx. 270 g Approx. 160 g Approx. 150 g (Pre-wired cable) (Pre-wired cable) (Pre-wired cable) Weight (packed state) Approx. 230 g Approx. 130 g Approx. 110 g (Pre-wired Connector (M12)) (Pre-wired Connector (M12)) (Pre-wired Connector (M12)) Case Zinc die-cast Operation PES (polyether sulfone) panel cover Material Lens Methacrylic resin Mounting Stainless steel (SUS304) Bracket Mounting Bracket (with screws), Adjustment screwdriver, Instruction manual, and Reflector (only for Retro-reflective Accessories Sensors) *1. Refer to MSR function of Technical Guide (Technical version). *2. NEMA: National Electrical Manufactures Association 3 E3S-C Engineering Data (Reference value) Parallel Operating Range Through-beam Through-beam Retro-reflective E3S-CT@ (-M1J) E3S-CT@ (-M1J) + E39-S61 Slit E3S-CR@1 (-M1J) + E39-R1 Reflector (Order Separately) (Provided) 2.5 800 400 E39-R1 Reflector Slit width: 4 mm 2 Y Y 600 300 Slit width: 2 mm 1.5 X X 400 200 Slit width: 1 mm 1 Y 200 100 0.5 X 0 0 0 10 20 30 40 4 8 12 16 1 2 3 4 Distance X (m) Distance X (m) −0.5 −200 −100 Distance X (m) −1 −400 −200 −1.5 Slit width: 0.5 mm −600 −300 −2 −2.5 −800 −400 Operating Range Diffuse-reflective E3S-CD@@ (-M1J) 50 Sensing object: white paper Y 300 × 300 mm 40 E3S-CD@2 30 X 20 E3S-CD@1 10 0 1 2 3 Distance X (m) −10 −20 −30 −40 −50 Excess Gain vs. Set Distance Through-beam Retro-reflective Diffuse-reflective E3S-CT@1 (-M1J) E3S-CR@1 (-M1J) + E39-R1 Reflector E3S-CD@@ (-M1J) (Provided) 500 500 500 Sensing object: White paper 300 × 300 mm Reflector: E39-R1 300 300 300 E3S-CD@1 100 100 100 50 50 50 E3S-CD@2 30 30 30 10 10 10 5 5 5 3 3 3 Operating Operating Operating level 1 1 level 1 level 0 1 2 3 0 10 20 30 40 0 1 2 3 4 Distance (m) Distance (m) Distance (m) 4 Distance Y (mm) Distance Y (m) Excess gain ratio Distance Y (mm) Excess gain ratio Distance Y (mm) Excess gain ratio E3S-C I/O Circuit Diagrams NPN Output Operation Operation Model Timing charts Output circuits mode selector Incident light Through-beam Model Receivers: Retro-reflective Models, Reflective Models No incident light ON Light indicator Light Brown 10 to 30 VDC Stability 1 indicator (Red) OFF indicator PNP output L side (Red) ZD ON (Green) Load Light-ON Output transistor Load (LIGHT ON) current transistor OFF Photo- electric Black NPN or PNP Operate 4 Load Sensor output selector * Control output main (e.g. relay) Reset circuit (Between brown A NPN output ZD and black D leads) E3S-CT11(-M1J) * transistor 0 V Blue 3 E3S-CT61(-M1J) * Incident light No incident light * Set the NPN or PNP selector to NPN. ON E3S-CR11(-M1J) Light indicator (Red) OFF E3S-CR61(-M1J) Connector Pin Arrangement D side ON Output Dark-ON (DARK ON) transistor OFF 1 E3S-CD11(-M1J) 2 4 Operate Load E3S-CD12(-M1J) 3 (e.g. relay) Reset E3S-CD61(-M1J) (Between brown A Pin 2 is not used. E3S-CD62(-M1J) and black D leads) Through-beam Model Emitters Brown Power 1 Connector Pin Arrangement indicator (Red) 1 Photo- electric 10 to 30 VDC 2 4 Sensor 3 main circuit Blue 3 Note: Pins 2 and 4 are not used. PNP Output Operation Operation Model Timing charts Output circuits mode selector Incident light Through-beam Model Receivers: Retro-reflective Models, Reflective Models No incident light ON Light indicator Brown 10 to 30 VDC Light Stability (Red) OFF 1 indicator L side indicator (Red) ON Output PNP output ZD Light-ON (Green) (LIGHT ON) transistor transistor OFF Photo- * Operate electric Black Load NPN or PNP 4 Control output Sensor (e.g. relay) Reset output selector main (Between blue C circuit Load Load and black D leads) NPN output current E3S-CT11(-M1J) * ZD Blue transistor 0 V E3S-CT61(-M1J) * Incident light 3 No incident light * Set the NPN or PNP selector to NPN. E3S-CR11(-M1J) ON Light indicator (Red) OFF E3S-CR61(-M1J) Connector Pin Arrangement D side ON Dark-ON Output (DARK ON) 1 transistor OFF E3S-CD11(-M1J) 2 4 Operate Load E3S-CD12(-M1J) 3 (e.g. relay) Reset E3S-CD61(-M1J) (Between blue C Pin 2 is not used. E3S-CD62(-M1J) and black D leads) Through-beam Model Emitters Brown Power Connector Pin Arrangement 1 indicator (Red) 1 Photo- electric 10 to 30 VDC 2 4 Sensor 3 main circuit Blue 3 Note: Pins 2 and 4 are not used. * Models numbers for Through-beam Sensors (E3S-CT11(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT11-L 2M), the model number of the Receiver, by adding "-D"　 (example: E3S-CT11-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. Plug (Sensor I/O Connector) Refer to Introduction Terminal No. Clas- Connector to Sensor I/O sifica- Conductor Application pin No. 1 tion Brown Connectors/Sensor 2 2 1 3 3 Blue Brown 1 Power supply (+V) Controllers for 4 Black 4 --- 2 --- details. DC Blue 3 Power supply (0 V) XS2F-D421-DC0-A Black 4 Output Note: Pin 2 is not used. 5 E3S-C Nomenclature Horizontal Model Vertical Model Operation panel cover Operation panel cover Light indicator Stability indicator SENS (red) Stability Light SL (green) D PNP ON indicator indicator SL Output selector *1 (green) (red) Sensitivity Min Max NPN L ON adjuster Min Max Sensitivity adjuster SENS PNP D·ON Operation selector *2 Output selector *1 Operation selector *2 NPN L·ON E3S-CD12 Note: The sensitivity adjuster on Through-beam and Retro-reflective Models is Model number different. *1. Use the output selector to select the type of output transistor, NPN or PNP. *2. Use the operation selector to select the operation mode. 6 E3S-C Safety Precautions Refer to Warranty and Limitations of Liability. WARNING This product is not designed or rated for ensuring ● Adjusting safety of persons either directly or indirectly. Optical Axis of Through-beam Sensor Do not use it for such purposes. The E3S-C Through-beam Models incorporates two lenses, one of which will be used as shown in the following illustration. When using a Slit, the Slit must be on the side where the lens to be used is located. Precautions for Correct Use Horizontal Model Vertical Model Do not use the product in atmospheres or environments that exceed Lens in use. product ratings. Lens in use. The Slit must be on this side. ● Wiring Cable • The E3S-C uses an oil-resistive cable to ensure oil resistivity. • Do not allow the cable to be bent to a radius of less than 25 mm. Unused lens Unused lens ● Mounting Mounting Water Resistance • When mounting the E3S-C, do not hit the E3S-C with a hammer, or To ensure the water resistance of the E3S-C, tighten the screws of the the E3S-C will loose watertightness. operation panel cover to a torque of 0.34 N·m to 0.54 N·m. • Use M4 screws to mount the E3S-C. The tightening torque of each screw must be 1.18 N·m maximum. ● Others Mounting Bracket • When mounting the E3S-C with the mounting bracket so that Oil and Chemical Resistance sensing objects will be in the direction of the mechanical axis, use • Although the E3S-C is oil-resistance, refer to the following table the optical axis lock holes. before using the E3S-C in places where oil may be sprayed on the • If it is not possible to mount the E3S-C so that the sensing objects E3S-C. will be in the direction the mechanical axis, move the E3S-C • Tests were carried out with the following oils and it was certified that upwards, downwards, to the left, or to the right and secure the E3S- the E3S-C resists these oils. C in the center of the range where the light indicator will be lit, at Kinematic viscosity which time make sure that the stability indicator is lit. Oil Product name PH 2 (mm /s (cst)) at 40°C Direct Mounting Velocite No.3 Mount the E3S-C as shown in the following illustration. Lubricating oil (manufactured by Exxon 2.02 Mounting with M4 Screws Mobil) --- Yushiron Oil No. 2 ac Two, 4.5 dia. through holes Water insoluble (manufactured by Yushi- Less than 10 machining oil ro Chemical Industry Co., Ltd.) M4 Yushiroken EC50T-3 (manufactured by Yushi- 7 to 9.5 M4 hole ro Chemical Industry M4 hole Co., Ltd.) Yushiron Lubic HWC68 Mounting with M3 Screws (manufactured by Yushi- 7 to 9.9 ro Chemical Industry Co., Ltd.) Water soluble --- machining oil Griton 1700D Two, M3 (manufactured by Toho 7 to 9.2 Chemical Industry Co., Ltd.) M4 hole Yushiroken S50N (manufactured by Yushi- 7 to 9.8 ro Chemical Industry M4 hole Co., Ltd.) M3 Note: 1. The E3S-C maintained a minimum insulation resistance of 100 MΩ Optical Axis Adjustment after the E3S-C was dipped in all the above oils at a temperature of 50°C for 240 hours. Optical Lock Holes 2. When using the E3S-C in a place where an oil other than the ones By inserting screws into the listed above is sprayed on the E3S-C, refer to the above kinematic optical axis lock holes, the viscosity and ph values. The location may be suitable for the E3S-C if the kinematic viscosity and pH values of the oil are close to the above Mounting Bracket will be in the Optical kinematic viscosity and pH values, but make sure that the oil does not direction of the optical axis of the axis Four optical contain any additive that may have a negative influence on the E3S-C. axis lock E3S-C. Mounting axis holes (M4) 7 E3S-C (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. Sensors Through-beam (Horizontal) E3S-CT11(-M1J) Pre-wired Connector (-M1J) M12 × 1 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached 4-dia. vinyl-insulated round cable with 3 conductors M3 × 5 2 50 (Conductor cross section: 0.2 mm (AWG 24), *2 Insulator diameter: 1.2 mm), 18.5 Light indicator (red) Standard length: 2 m *3 20 20.4 Mounting Holes 22.2 Stability Emitter: E3S-CT@@-L indicator Two, M4 Receiver: E3S-CT@@-D (green) 20 4.2 9.2 25.4 4.2 8.3 Stainless steel (SUS304) 6.2 Lens (17 × 11) Optical axis 38.2 2.2 4 23 29.5 18 17.3 9.3 A* 1 Two, M4 20.8 25.4 1.5 *1. The Mounting Bracket can be attached to side A. *2. The Emitters for Through-beam Sensors only have the power indicator (red). 2 *3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm , insulator diameter: 1.3 mm) and a standard length of 2 m. Note: Models numbers for Through-beam Sensors (E3S-CT11(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT11-L 2M), the model number of the Receiver, by adding "-D"　 (example: E3S-CT11-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. 8 E3S-C Through-beam (Vertical) Pre-wired Connector (-M1J) E3S-CT61(-MJ) M12 × 1 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached 4-dia. vinyl-insulated round cable with 3 conductors 57 2 (Conductor cross section: 0.2 mm (AWG24), Optical axis Insulator diameter: 1.2 mm), 15.8 7.4 Standard length: 2 m *3 Optical axis 20 20.4 Mounting Holes 22.2 Lens (17 × 11) Two, M4 20 4.2 9.2 25.4 4.2 4.2 Stainless steel 12.9 12.9 (SUS304) 25.4 31 Stability indicator (green) 43.8 7.2 Light indicator (red)*2 2.2 5.8 20.2 23 32.2 12 A* 1 M3 × 5 Two, M4 23.2 1.5 *1. The Mounting Bracket can be attached to side A. *2. The Emitters for Through-beam Sensors only have the power indicator (red). 2 *3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm , insulator diameter: 1.3 mm) and a standard length of 2 m. Retro-/Diffuse-reflective (Horizontal) Pre-wired Connector (-M1J) E3S-CR11(-M1J) M12 × 1 4-dia. vinyl-insulated round cable E3S-CD11(-M1J) Standard length: 300 mm With Mounting Bracket Attached E3S-CD12(-M1J) 4-dia. vinyl-insulated round cable with 3 conductors M3 × 5 2 50 (Conductor cross section: 0.2 mm (AWG24), Insulator diameter: 1.2 mm), Light indicator (red) 18.5 Standard length: 2 m 20 20.4 22.2 Mounting Holes Stability indicator Two, M4 (green) 20 4.2 9.2 25.4 4.2 8.3 Stainless steel (SUS304) 6.2 Lens (17 × 11) Receiver 38.2 2.2 4 23 9 29.5 1 18 17.3 9.3 A* Emitter Optical axis Two, M4 1.5 20.8 25.4 *The Mounting Bracket can be attached to side A. Note: Models numbers for Through-beam Sensors (E3S-CT61(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT61-L 2M), the model number of the Receiver, by adding "-D"　 (example: E3S-CT61-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. 9 E3S-C Retro-/Diffuse-reflective (Vertical) Pre-wired Connector (-M1J) E3S-CR61(-M1J) M12 × 1 4-dia. vinyl-insulated round cable E3S-CD61(-M1J) Standard length: 300 mm With Mounting Bracket Attached E3S-CD62(-M1J) 57 4-dia. vinyl-insulated round cable with 3 conductors 9 Receiver 2 5 (Conductor cross section: 0.2 mm (AWG24), 2.4 Insulator diameter: 1.2 mm), 20.8 Emitter Standard length: 2 m Optical axis 20 20.4 Mounting Holes 22.2 Two, M4 Lens (17 × 11) 20 4.2 9.2 25.4 4.2 4.2 Stainless steel 12.9 12.9 (SUS304) 25.4 31 Stability indicator (green) 43.8 7.2 Light indicator (red) 2.2 5.8 20.2 23 32.2 12 A* 1 M3 × 5 Two, M4 23.2 1.5 *The Mounting Bracket can be attached to side A. Accessories (Order Separately) Snap-in Long Slit (For Through-beam Models) E39-S61 1 A 0.2 11 20 6.2 11.8 Dimension Material Quantity A (mm) 0.5 3.8 6.5 1 set each for 1 Stainless Emitter/Receiver steel 20.1 2 (8 Slits total) 4 Reflectors Refer to E39-L/E39-S/E39-R for details. Mounting Brackets Refer to E39-L/E39-S/E39-R for details. 10 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2015.4 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2015 All Right Reserved.