Long-distance Proximity Sensor TL-LP/LY CSM_TL-LP/LY_DS_E_4_1 Long-distance Model with a Sensing distance of 50 mm. Be sure to read Safety Precautions on page 3. Ordering Information Appearance Sensing distance Output configuration Model 3-wire DC (normally open) TL-LP50 1M Column type (flat-surface mounting) 2-wire AC (normally open) TL-LY50 1M 50 mm Note: Models with different frequencies are available. The model numbers are TL-L@50B. Ratings and Specifications Item Model TL-LP50 TL-LY50 Sensing distance 50 mm±10% Set distance 0 to 40 mm Differential travel 10% max. of sensing distance Ferrous metals (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on Sensing object the next page.) Standard sensing object Iron, 100 × 100 × 1 mm Response time 15 ms max. 25 ms max. Power supply voltage (oper- 12 to 24 VDC (10 to 30 VDC), ripple (p-p) 10% max. 100 to 220 VAC (90 to 250 VAC), 50/60 Hz ating voltage range *) Current consumption 10 mA max. (with no load) --- Leakage current --- Refer to Engineering Data on the next page. NPN open collector with a maximum current of Switching capacity 10 to 200 mA Control 200 mA at 30 VDC output 3 V max. under a load current of 200 mA and a cable Residual voltage Refer to Engineering Data on the next page. length of 2 m Indicators Operation indicator (red) Operation mode (with sens- NO. Refer to the timing charts under I/O Circuit Diagrams on page 3 for details. ing object approaching) Ambient temperature Operating/Storage: −25 to 70°C (with no icing or condensation) Ambient humidity Operating/Storage: 35% to 95% (with no condensation) Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C Voltage influence ±2% max. of sensing distance within a range of ±10% of rated power supply voltage Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case 500 VAC (50/60 Hz) for 1min between current- 2,000 VAC (50/60 Hz) for 1 min between current- Dielectric strength carrying parts and case carrying parts and case Vibration resistance 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions (destruction) Shock resistance 2 1,000m/s 10 times each in X, Y, and Z directions (destruction) Degree of protection IEC IP67 Connection method Pre-wired Models (Standard cable length: 1 m) Weight (packed state) Approx. 1.4 kg Materi- Case Die-cast aluminum als Sensing surface Polyester Accessories Instruction sheet * Full-wave rectified power supplies with a mean output of 24 VDC ±10% are available for the TL-LP50. 1 TL-LP/LY Engineering Data (Reference Value) Sensing Area Leakage Current TL-LP/-LY TL-LY50 80 3.0 Y mA 100/200 VAC 70 VL 2.5 X 60 2.0 50 200 VAC 1.5 40 30 1.0 100 VAC 20 0.5 10 0 0.3 0.5 1 5 10 50 100 −60 −40 −20 0 20 40 Distance Load resistance (kΩ) Y (mm) 85-dia. head Residual Voltage TL-LY50 at 100 VAC TL-LY50 at 200 VAC 150 250 100 Operate 200 Operate ON ON 150 V V mA 100 VAC mA 50 VL 200 VAC 100 VL 50 Reset Reset OFF OFF 2 3 5 10 50 100 500 2 5 10 50 100 500 Load current (mA) Load current (mA) Column-type Sensing Object Diameter Sensing Object Size and Material vs. Sensing Object Thickness and and Material vs. Sensing Distance Sensing Distance Material vs. Sensing Distance TL-LP/-LY TL-LP/-LY TL-LP/-LY 60 70 @l 70 t = 1 mm 60 Aluminum 50 X Iron Reset Iron 60 50 Stainless steel Operate 40 Reset (SUS304) Iron 50 40 l > 120 Operate D dia. 30 40 30 Brass 30 20 20 Reset 20 Reset Brass @100 10 Operate t 10 Aluminum Operate 10 0 50 100 150 0 10 30 50 70 90 120 140 Size of sensing object: I (mm) 01 0.01 0.02 0.05 0.1 2 External diameter D dia. (mm) Thickness of sensing object t (mm) 2 Load voltageVL (V) Distance X (mm) Distance X (mm) Distance X (mm) Leakage current (mA) Load voltageVL (V) Distance X (mm) X X TL-LP/LY I/O Circuit Diagrams 3-wire DC Model Output configuration Model Timing charts Output circuit Brown Present +V Sensing object Not present Load 1.8 Ω Black Proximity Output transistor ON NO TL-LP50 Sensor (Load) 200 mA max. OFF main circuit Operation indicator ON 2.2 Ω Blue (red) OFF 0 V 2-wire AC Model Output configuration Model Timing charts Output circuit Brown Load Present Sensing object Not present Proximity AC power Operate Sensor supply NO TL-LY50 Load main Reset circuit Blue Operation indicator ON (red) OFF Safety Precautions WARNING This product is not designed or rated for Mutual Interference ensuring safety of persons. When two or more Sensors are mounted face-to-face or side- Do not use it for such purposes. by-side, separate them as shown below. Face-to-face Mounting Parallel Mounting Precautions for Correct Use A B Do not use this product under ambient conditions that exceed the ratings. ● Design Effects of Surrounding Metal (Unit: mm) Be sure to separate the Sensor from surrounding metal Model Distance A B objects as shown in the following illustration. TL-L@50 1,000 (500) 700 (176) Note: Figures in parentheses will apply if the Sensors in use are different from each other in response frequency. 150 mm 70 mm 70 mm (Unit: mm) Dimensions Unless otherwise specified, the tolerance class IT16 is used for dimensions in this data sheet. TL-LP50 Operation 76 indicator TL-LY50 44 106 Four, 7-dia. holes Mounting Holes (red) 20 88 Four, 6.5-dia. holes *2 16 85 dia. 30 88 106 88 *1 88 18.5 R5 75 5 *1. Vinyl cabtire cable: TL-LP50: 9.4-dia. vinyl-insulated round cable with 3 conductors 2 (Conductor cross section: 0.75 mm , Insulator diameter: 2.8 mm), Standard length: 1 m TL-LY50: 9.0-dia. vinyl-insulated round cable with 2 conductors 2 (Conductor cross section: 0.75 mm , Insulator diameter: 2.8 mm), Standard length: 1 m *2. Remove the hexagon nut if a PF1/2 cable protective tube is applied. In the interest of product improvement, specifications are subject to change without notice. 3 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2015.7 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2015 All Right Reserved.