OMRON AUTOMATION Z4D-F04A

Micro Displacement Sensor Z4D-F Compact, High-performance Micro Displacement Sensor ■ Meets various needs with high performance at the resolution of 5 µm. ■ Numerous applications are possible when the analog output model is integrated with OMRON’s K3TX Intelligent Signal Processors. ■ ON/OFF output model (NPN open collector) is available. Ordering Information ■ Z4D-F Output Model Analog Z4D-F04A ON/OFF Z4D-F04D ■ Accessories (Attached) Item Z4D-F04A Z4D-F04D Mounting bracket 1 pc. 1 pc. Mounting screws (M3 x 2) 2 pcs. 2 pcs. Connector with 1-m cord 1 pc. 1 pc. Screwdriver --- 1 pc. Operation Manual 1 copy 1 copy 1 Z4D-F Z4D-F Specifications ■ Ratings/Characteristics Item Z4D-F04A Z4D-F04D Supply voltage 12 to 24 VDC±10%, ripple voltage (p-p): 10 mV max. Current consumption 35 mA max. Sensing range 4±1.25 mm (see note 1) Light source Red LED with a wavelength of 700 nm Spot diameter 1.5 x 1.5 mm max. (at the sensing range of 4 mm) (see note 2) Connection imped- 200 kΩ min. --- ance (see note 3) Resolution 5 µm max. --- (see note 4) Hysteresis --- 40 µm (see note 1) Linearity (see note 5) ±1% FS --- Analog output 1 to 5 V (1.6 V/mm±10%) --- (see note 1) Control output --- NPN open collector, 12 to 24 VDC, 50 mA max. Residual output volt- --- 1 V max. age Response time 5 ms max. 1.5 ms max. (see note 6) Temperature influ- 0.15% FS/°C--- ence (see note 7) Indicator PWR indicator (green): Lit when power is supplied STB indicator (green): Lit when illumination is suffi- ALM indicator (red): Lit when illumination is insufficient. cient. OPE indicator (orange): Lit when output is ON. Ambient temperature Operating: –10°C to 55°C (with no icing) Storage: –15°C to 60°C (with no icing) Ambient humidity Operating: 35% to 85% (with no icing) Ambient illumination Operating: 3000 lx max. (incandescent lamp), 10,000 lx max. (sunlight) Enclosure rating IP50 (IEC standard) Vibration resistance Destruction: 10 to 500 Hz (1-mm max. single amplitude) for 11 min for 3 times each in X, Y, and Z directions 2 Shock resistance for 3 times each in X, Y, and Z directions (total of 18 times) Destruction: 500 m/s Dielectric strength 1,000 VAC for 1 min between current carry parts and case Tightening torque 0.6 N·m max. Material ABS (Polycarbonate for the sensing part) Weight Approx. 10 g (without connector cable) Insulation resistance 20 MΩ min. (at 500 VDC) Cable length 1 m Note: 1. The values are for N8.5 Munsell paper. 2 2. The spot diameter is defined by 1/e of the Sensor’s laser beam center. Although a sub-beam may be observed around the main beam, this does not mean that the product is defective. 3. Refers to input impedance of a device to be connected. 4. Resolution (Z4D-F04A) The resolution is the peak-to-peak displacement conversion value of the analog displacement output (Conditions: N8.5 Munsell mat paper at the center of measurement point with a power ripple noise of 10 mV (p-p) max.) Output fluctuation 5. The value is the peak-to-peak error rate of a displacement output voltage line with N8.5 Munsell mat paper. The value varies with the sensing object. 2 Z4D-F Z4D-F 6. Response Time (Z4D-F04A) The response time of the Sensor (Z4D-F04A) is the time required for the analog displacement output to increase from 10% to 90% of the full value (at the rise time) or decrease from 90% to 10% of the full value (at the fall time). Displacement value tr: rise time tf: fall time Analog dis- placement output The response time of the Sensor (Z4D-F04D): ON/OFF switching time 7. The value is at the sensing range of 4 mm. Engineering Data (Reference Value) ■ Characteristics Data Analog Output Model (Z4D-F04A) Sensing Distance vs. Analog Output Characteristics Angle Characteristics with Difference in Horizontal (Typical) Inclination Standard paper PBT SPCC Positive inclination Negative inclination Inclination angle (°) Sensing distance (mm) Analog Output Characteristics with Difference in Sensing Angle Characteristics with Difference in Vertical Inclination Object Standard paper PBT Standard paper SPCC PBT SPCC Positive inclination Negative inclination Inclination angle (°) Distance (mm) 3 Error (%FS) Linear output (V) Error (%FS) Error (%FS) Z4D-F Z4D-F Temperature Characteristics Vcc = 24 V Vcc = 10.8 V Vcc = 26.4 V Temperature (°C) Resolution Characteristics with Difference in Reflection Rate Reflection factor (%) ON/OFF Output Model (Z4D-F04D) Sensing Distance vs. Adjustor Angle Characteristics Standard paper PBT SPCC Sensing distance (mm) Note: The PBT plastic referred in this data was detected under its natural state. 4 Adjustor angle (°) Error (%FS) Resolution (µm) Z4D-F Z4D-F Nomenclature ■ Analog Output (Z4D-F04A) (1) (2) (1) Power (PWR) Indicator The green PWR indicator is lit when power is properly supplied to the Sensor. (2) Alarm (ALM) Indicator The red ALM indicator is lit if there is no sensing object or the reflectivity of the sensing object is low and it is impossible for the Sensor to process the light reflected to the Sensor. The indicator is lit when the amount of light is less than what is required for computation by the Sensor. When the ALM indicator is lit, make necessary adjustments so that the indicator turns OFF. Appropriate amount of light: Not lit Insufficient amount of light: Lit in red ■ ON/OFF Output (Z4D-F04D) (3) (4) (5) (3) Stability (STB) Indicator The green STB indicator is lit when the Sensor is receiving suffi- cient light to process. If the indicator is not lit, adjust the amount of light to turn on the indicator. (4) Operation (OPE) Indicator The Sensor is synchronized with the ON/OFF output and the orange OPE indicator is lit when the Sensor has ON output. (5) Distance Adjustor The ON/OFF position can be set with the distance adjustor if a sensing object is at the sensing range (i.e., 4±1.25 mm). The ON/ OFF position will shift farther from the Sensor if the distance adjustor is turned clockwise and the ON/OFF position will shift closer to the Sensor if the distance adjustor is turned counter- clockwise. 5 Z4D-F Z4D-F Operation ■ Connections/Output Circuits Analog Output Connector (Brown) 12 to 24 VDC (Black) 0 to 6.5 V Output (Blue) 0 V NPN Open Collector Output Connector (Brown) 12 to 24 VDC Load (Black) Output (Blue) 0 V 6 Signal Signal processor processor Z4D-F Z4D-F Dimensions ■ Z4D-F04A Operation indicator Stability indicator Mounting Holes Two, M3 Mounting holes Mounting bracket can be attached to this side. Receiver Optical axis Two, M3 X 12 Emitter ■ Z4D-F04D Operation indicator Stability indicator Distance adjustor Mounting Holes Two, M3 Mounting holes Mounting bracket can be attached to this side. Receiver Optical axis Two, M3 X 12 Emitter ■ Accessories The following products are provided with the Sensors. The products can also be purchased separately. E39-L69 Mounting Bracket Stainless steel (SUS304) 7 Z4D-F Z4D-F EE-1010D Connector with 1-m Cord Two, C1 Terminal Arrangement No. Designation Color 1 Vcc Brown (red) 2--- --- 3 Output Black (white) 4GND Blue (black) Installation ■ Controller Connections Z4D-F04A and K3TX-VD Z4D-F04D and S3D2 (Black) (Brown) (Black) (Brown) Z4D-F04A (Blue) (Blue) 12 to 24 VDC 0 V +12 V 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 K3TX-VD22@-@@ Note: 1. Use a K3TX DC voltage input model. Note: Reverse operation is possible with the signal input selec- tor of the S3D2. 2. K3TX models are available in various output units. Se- lect the most appropriate K3TX model depending on the application. 3. For details about the K3TX, refer to the K3TX Datasheet. 4. The diagram shown here is for a K3TX model with DC power specifications. When using a K3TX with AC power specifications, separate the AC power supply to the K3TX from the DC power supply to the Z4D-F04A. 8 Z4D-F Z4D-F !Caution Item Examples Power supply Incorrect Incorrect Do not impose an excessive voltage on the Brown Brown Load Z4D-F, otherwise it may explode or burn. Sensor Do not impose 100 VAC on any Z4D-F Sensor Black Black model, otherwise it may explode or burn. Blue Blue Load short-circuit Incorrect Load Do not short-circuit the load, or the Z4D-F short- (Brown) Load circuit may explode or burn. Sensor (Black) (Blue) Wiring Wrong polarity Incorrect Incorrect Be sure to wire the Z4D-F correctly and be Brown Brown careful not to connect the polarities incor- Load rectly, otherwise it may explode or burn. Sensor Sensor Black Black Blue Blue Wrong wiring Incorrect Incorrect Brown Brown Load Sensor Sensor Black Black Blue Blue Connection with no load Incorrect Brown +12 to 24 V If connected to the power supply without any load, internal elements may explode or burn. Make sure to connect a proper load to the Z4D-F. Sensor Black 0 V Blue 9 Z4D-F Z4D-F ■ Correct Use Mounting Z4D-F04A Install the Sensor so that the optical axis of the Sensor and the Analog Output surface of the object meet at right angles (i.e., the panel that The Z4D-04A has an output of 3 V if a sensing object is located at incorporates the light source is parallel with the object). For accu- the standard distance (i.e., 4±0.3 mm). The output decreases if rate results, it is recommended that the sensing distance is set to the sensing object is closer to the Sensor and the output the measurement point (4 mm). increases if the sensing object is farther from the Sensor. The output changes by 1.6 V±10% if the sensing object moves by 1 mm. The standard upper and lower limits of the output are 6.5 and 0 V respectively. If there is no sensing object or the reflectivity of the sensing object is low and no light is reflected to the Sensor, the analog output will output the standard upper limit. Analog Output Diagram Light source surface Sensing object surface Note: As the optical axis will be adjusted later, temporarily fix the Z4D-F04D Sensor. ON/OFF Output Diagram Wiring The ON/OFF position can be set with the distance adjustor if a Connect the Sensor to the controlling device using an attached sensing object is at the sensing range (i.e., 4±1.25 mm). The ON/ sensor cable. Do not switch the power ON during wiring. Refer to OFF position will shift farther from the Sensor if the distance the instructions on the Sensor and the connection diagram (page adjustor is turned clockwise and the ON/OFF position will shift page 8) before connecting the Sensor to the controlling device. closer to the Sensor if the distance adjustor is turned counter- clockwise. Axis Adjustment If there no sensing object is present or if the reflectivity from a When the Sensor power is switched ON, the red transmitter indi- sensing object is too small to reach the Sensor, the output will cator is lit. Move the Sensor so that the red beam (see the figure turn OFF. below) focuses on the object. The entire light beam should be focused on the object or an error will result. After the optical axis has been adjusted, tighten the mounting screws firmly. Surface of object Correct Incorrect Distance adjustor position Spot 10 Analog output (V) Z4D-F Z4D-F Precautions Install the Sensor in a clean environment keep the filter (on the Environment front of the Sensor) free from oil and dust. If affected by oil or Refrain from using the Micro Displacement Sensor in a strong dust, clean the Sensor as follows: electromagnetic field or in an environment where the operation of 1. Use a blower brush (used to clean camera lenses) to blow the Sensor is subject to the reflection of intensive light (such as a large dust particles from the surface. Do not blow the dust laser beam or an electric arc welding machine). away with your mouth. The Displacement Microsensor cannot accurately sense a mirror- 2. Use a soft cloth (for lenses) with a little alcohol to remove like object, a transparent object, one with an extremely small the remaining dust. reflection ratio, an object smaller than the diameter of the Sen- Do not use a scrubbing action when cleaning as a scratch sor’s sensing spot, or an inclined object. on the filter could result in the Sensor malfunctioning. Wiring Connector The power supply cable for the Z4D-F04A/D should not be wired When removing the connector from the Sensor, be sure to hold with high-voltage lines or power lines in order to avoid interfer- the connector and pull it together with the attached cable. ence, damage, or malfunction. If pulled by the cable alone, it will damage the lock mechanism Do not solder wires to the Sensor connector, otherwise the Sen- inside the connector. sor may malfunction. Interference Others Z4D-F04A/D Micro Displacement Sensors can be installed within Do not use switching power supplies that generate excessive close proximity to each other and operate independently without noise, which may cause sensing errors. interference (refer to the figures below). However, if they are The following LC filter effectively reduces noise. installed at an oblique angle to each other, interference may result. Power Sensor source The Sensor cannot sense an object accurately if the surface of the object consists of different materials placed next to each other (refer to the figures below). In such a case install the Sensor so that the boundaries of the materials and the Sensor are parallel. When using the Micro Displacement Sensor in combination with another type of Sensor (such as a Photoelectric Sensor), the sen- sor beams should be as close to perpendicular as possible. 11 Z4D-F Z4D-F ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. CSM_Z4D-F_DS_E_2_1 E251-E1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company Sensing Devices Division H.Q. Application Sensors Division Shiokoji Horikawa, Shimogyo-ku, Kyoto, 600-8530 Japan Tel: (81)75-344-7068/Fax: (81)75-344-7107 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2013.12 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2013 All Right Reserved.