WWW.PHIHONG.COM 30W Power over Ethernet Adapter High Power, High Temperature Single Port Injector Features • Fully Compliant IEEE802.3at • Full Protection OCP, OVP • Diagnostic LEDs • Gigabit Compatible • Non-Vented Case • Cisco AP1250 Full Power Support • Wide Temperature Range: -20 to +55°C Applications • IP Telephones • Security Cameras • Wireless Network Access Points • IP Print Servers • Blue Tooth Access Points Safety Approvals • cUL/UL • CE Mechanical Characteristics • Length: 166mm (6.48in) • Height: 44mm (1.73in) • Width: 80mm (3.15in) • Weight: 0.2Kg (0.44lb) Output Specifications DC Output Model Load Regulation Voltage Min. Max. Line Load 1 POE30U-560(G)-HT 56V 0A 0.55A 54-57V DC under all conditions Notes: Consult factory for availability Phihong is not responsible for any error, and reserves the right to make changes without notice. Please visit our website at www.phihong.com for the most up-to-date specifications and contact information. Revision 5/29/2018 POE30U-560(G)-HT Characteristics WWW.PHIHONG.COM INPUT: Dielectric withstand (HI-POT) test AC Input Voltage Range Pri to Sec: 4242VDC for 1 minute, 10mA 85 to 264VAC Pri to F.G.: 2121VDC for 1 minute, 10mA AC Input Voltage Rating Immunity 100 to 240VAC ESD: IEC61000-4-2 RS: IEC61000-4-3 AC Input Frequency EFT: IEC61000-4-4 47-63Hz Surge: IEC61000-4-5 CS: IEC61000-4-6 AC Input Current Voltage Dips IEC61000-4-11 0.95A (RMS) 90VAC at max. load Harmonic: IEC61000-3-2 0.55A (RMS) 240VAC at max. load Insulation Resistance Leakage Current Pri to Sec: >10M OHM 500VDC 0.25mA max 264VAC 50Hz, input to PE Pri to F.G.: >10M OHM 500VDC 3.5mA max 264VAC 50Hz ,input to output FEATURES: AC Inrush Current Over Voltage Protection 15A (RMS) max for 115VAC 120VDC shall not be exceeded- latching 20A (RMS) max for 230VAC Over Current Protection OUTPUT: 685mA max Total Output Power 30W at 56V DC Short Circuit Protection The output can be shorted permanently Efficiency without damage 75% (typical) at max load, 120VAC 60Hz Thermal Protection Hold-up Time Auto-recover 16mS min. and 120VAC at max load Indicators Transient O/P Voltage Protection Green LED 1: Power detected “ON” 60V max switch on/off any AC line phase Green LED 2: Valid “PoE Plus” load detected and connected ENVIRONMENTAL: Green LED 3: Valid IEEE802.3at load Temperature detected and connected Operation -20°C to +55°C Non-operation -40°C to +85°C Input Connector Humidity 10 to 90% IEC320 C14 inlet receptacle EMI Output Connection Complies with FCC Class B +pins 3, 6 Complies with EN55032 Class B - pins 1, 2 Revision 5/29/2018 Dimension Diagram Unit: mm Description of LED Functions for Gigabit Power Injector Power-up Sequence: Upon power-up, all 3 LEDs will light for 2 seconds, as part of the self-test for the internal microprocessor software. After the 2 seconds, the "ON" LED will illuminate green. The DC output voltage is now available for powering a compliant load (to the 802.3at PoE standards). Revision 5/29/2018 Detection Sequence: Once a compliant load is attached to the output RJ45 connector, the green "CONNECT" LED will illuminate. Should the load be non-compliant then the LEDs will blink a code signifying the cause for non-detection. Detection Failure Codes: 1. Incorrect resistive signature – The green “CONNECT” and red “FAULT” LEDs will blink 3 times. 2. Incorrect capacitive signature – The green “ON” LED will blink 3 times. 3. Incorrect Voffset – The green “CONNECT” and green “ON” LEDs will blink 3 times. 4. Unstable current measurement – The green “ON” LED will blink 3 times 5. Low voltage sensed during detection (overload) – The red “FAULT” LED will blink 3 times After the LEDs blink 3 times the Power Injector will continue to try to detect a valid load. Until the correct load is applied, the LEDs will continue to blink. If there is an open circuit connected to the output RJ45 then the LEDs will not blink but the Power Injector will continue to try to detect a valid load. Fault Sequence: Should a fault occur such as an overload or short circuit then the red "FAULT" LED will illuminate. The red “FAULT” LED will illuminate for 2 seconds and then go off as the power supply tries to re-detect a valid load. If there is a problem detecting the load, the LED will indicate the possible fault as per the codes in the section above. Revision 5/29/2018