WWW.PHIHONG.COM 8-Port 72W per Port Midspan POE576U-8UP-N for 10/100/1000 Base-T Networks Features • Proprietary Detection, Disconnect and • Full Power of 576W--72W per Port Overload Protection • Limited Power Source • Full Protection OTP, OCP, OVP • Gigabit Compatible • Ultra PoE at 72W per port • 1U Rack Mounting Kit Ships with • 1 Year Warranty Unit • SNMPv2c Management Applications • Wireless Access Points • Security Systems • Computer Workstations • IP Cameras Safety Approvals • cUL/UL • CE Mechanical Characteristics • Length: 438mm (17.25in) • Height: 44.5 mm (1.75in) • Width: 228mm (8.98in) • Weight: 3.8Kg (8.5lbs) Output Specifications Load DC Output (1) Model Output Power per Port (2) Voltage Min. Max. POE576U-8UP-N 56V 15mA 1.29A 72W Note (1): Model without SNMP management available upon special request Note (2): Max load applies to compliant load at 12.5K detection. If operating at 25K “IEEE802.3at mode” max load is 0.6A Reference files: 1. SNMPv2c_User_Manual-Rev1.7.pdf 2. Multiport_Midspan_Installation_Manual.pdf 3. SNMPv2c_Firmware-Rev1.7.zip 4. SNMPv2c_MIB_10_30_2009.zip Phihong is not responsible for any error, and reserves the right to make changes without notice. Please visit our website at www.phihong.com for the most up-to-date specifications and contact information. Revision 1/11/2018 POE576-8UPN Characteristics WWW.PHIHONG.COM INPUT: ENVIRONMENTAL Input Voltage Rating Temperature 100 to 240VAC Operation 0 to +40C Non-Operation -25 to +65C Input Voltage Range Humidity 5 to 90% 90 to 264VAC EMC AC Input Current EN55022 Class A, FCC Class A with UTP 9.0A (RMS) 90VAC at maximum load cabling 4.25A (RMS) 230VAC at maximum load EN55022 Class B, FCC Class B with FTP cabling AC Input Frequency 47 to 63Hz Isolation Test Primary to Secondary: 4242VDC for 1 Leakage Current minute 3.5mA maximum at 264VAC and 60Hz Primary to Ground: 2121VDC for 1 minute Secondary to Ground: 2121VDC for 1 Max In-Rush Current: minute 30A for 115VAC at maximum load 60A for 230VAC at Maximum load Immunity EN50082-1 (Cold Start at Ambient 25°C) ESD: EN61000-4-2 Level 3 RS: EN61000-4-3 Level 2 OUTPUT: EFP: EN61000-4-4 Level 2 Total Output Power Surge: EN61000-4-5 Level 3 72W per port CS: EN61000-4-6 Level 2 576W Maximum Total Power Voltage Dips: EN61000-4-11 Harmonic: EN61000-3-2 Class A Ripple and Regulation 250mV maximum IEEE802.3af/at Interoperability If 25K Ohm is detect the unit operates in Efficiency “IEEE802.3at mode” 33.6W 2 pair 75% (typical) at maximum load, and powering. 12.5K detection resistance 120VAC 60Hz required for full power. Hold-Up Time FEATURES: 16mS min. 120VAC and maximum load Cisco Legacy Detection No extern parts required for Legacy Transient O/P Voltage Protection Devices: 60V maximum at switch on and off at any VoIP Phones:7910, 7912, 7940, 7960 AC line Phase Access Points350, 1100, 1200 Turn-On Delay Time 20 sec maximum at maximum load, 120VAC 60Hz POE576-8UPN Characteristics WWW.PHIHONG.COM Over-Voltage/Current, Short Circuit Input Connector Protection AC Input IEC320 C14 The output can be shorted permanently without damage Output Connection 4-pair powering for full power Over Temperature Protection Pins 3,6, 4,5(+) Automatic shutdown without damage Pins 1,2, 7,8 (-) Indicators 2-pair powering for IEEE802.3at mode Solid Green LED: Power detected “ON” Pins 3,6(+) Flashing Green: IEEE802.3at or (af) Pins 1,2 (-) detected Yellow LED: Fault detected SNMPv2c management port Interface NIC interface for remote management via secure IP access POE576U-8UPN Dimension Diagram