PROTEK PM1100 SERIES 1100 Watt Enclosed with Fan Power Supply 1100 WATT MEDICAL POWER SUPPLIES Measures: 9.25 x 5.91 x 2.40” FEATURES PM1100 SERIES  BF Class insulation  Operation up to 5000 meters  Less than 220 μA leakage current  EN55011 Class B conducted emissions  Inhibit - TTL low to disable output  Standard PS Off and DC OK signals  High Efficiency 89% typical  Standby output 5 VDC at 200 mA  Variable speed internal fan SAFETY STANDARD APPROVALS INPUT SPECIFICATIONS Input voltage: 90-264 VAC UL ES 60601-1, CSA C22.2 No. 60601-1 Input frequency: 47-63 Hz File No. E178020 (Pending) Input current: 16 A (rms) @100 VAC, 60 Hz 8 A (rms) @ 240 VAC, 50 Hz TÜV EN 60601-1 (Pending) Earth leakage current: 220 μA max. @ 264 VAC, 63 Hz GENERAL SPECIFICATIONS OUTPUT SPECIFICATIONS Switching frequency: 40 KHz to 200 KHz Output voltage/current: See rating chart. Efficiency: See rating chart Maximum output power: See rating chart. Hold-up time: 10 ms minimum at 110 VAC Ripple and noise: 1% peak to peak maximum Line regulation: ±0.5% maximum at full load Remote sense Compensation for cable losses up to 0.5 V Inrush current: 50 A @ 115 VAC, or 100 A @ 230 VAC, at Overvoltage protection: Set at 112-140% of nominal output voltage 25℃ cold start Overcurrent protection: Set at 120-140% of maximum output Withstand voltage: 4000 VAC from input to output (2MOPP) current 1500 VAC from input to ground (1MOPP) Thermal shutdown Protected to overtemperature conditions 1500 VAC from output to ground Temperature coefficient: All outputs ±0.04% /℃ maximum MTBF: 300,000 hours at full load at 25℃ ambient, Transient response: Maximum excursion of 4%, recovering to calculated per MIL-HDBK-217F 1% of final value within 500 us after a 25% EMC Performance step load change EN55011: Class B conducted, class B radiated Standby power 5 V at 200 mA maximum FCC: Class B conducted, class B radiated Fan power 12 V at 1.0 A maximum VCCI: Class B conducted, class B radiated EN61000-3-2: Harmonic distortion, class A and D EN61000-3-3: Line flicker ENVIRONMENTAL SPECIFICATIONS EN61000-4-2: ESD, ±8 KV air and ±6 KV contact Operating temperature: -10℃ to +70℃ EN61000-4-3: Radiated immunity, 3 V/m Storage temperature: -40℃ to +85℃ EN61000-4-4: Fast transient/burst, ±2 KV Relative humidity: 5% to 95% non-condensing EN61000-4-5: Surge, ±1 KV diff., ±2 KV com Derating: Derate from 100% at +50℃ linearly to EN61000-4-6: Conducted immunity, 3 Vrms 50% at +70℃, applicable to convection EN61000-4-8: Magnetic field immunity, 3 A/m Voltage and forced-air cooling conditions EN61000-4-11: dip immunity OUTPUT VOLTAGE/CURRENT RATING CHART Min. Max. Peak Ripple & Max. Output @ 1100 W (2) (1) Model V1 Current Current Current Tol. Noise Power 115/230 Vac PM1100-14C 24 V 0 A 45.84 A 52.10 A ±2% 240 mV 1100 W /1250 W 87 /88% PM1100-15C 28 V 0 A 39.29 A 44.65 A ±2% 280 mV 1100 W /1250 W 87 /88% PM1100-16C 32 V 0 A 34.38 A 39.07 A ±2% 320 mV 1100 W /1250 W 87 /88% PM1100-17-1C 34 V 0 A 32.35 A 36.77 A ±2% 340 mV 1100 W /1250 W 87 /89% PM1100-17C 36 V 0 A 30.56 A 34.73 A ±2% 360 mV 1100 W /1250 W 87 /89% PM1100-18-1C 42 V 0 A 26.20 A 29.77 A ±2% 420 mV 1100 W /1250 W 87 /89% PM1100-18C 48 V 0 A 22.92 A 26.10 A ±2% 480 mV 1100 W /1250 W 87 /89% NOTES: 1. Peak current and power possible at 170-260 VAC input, 10 seconds, 35% duty cycle. 2. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 10 μF tantalum capacitor in parallel with a 0.1 μF ceramic capacitor across the output. Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. 1 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-pm1100-power-supply.html h t t p: / / pow e r. sa ge r. c om PROTEK PM1100 SERIES 1100 Watt Enclosed with Fan Power Supply UNIVERSAL INPUT PM1100 MEDICAL SERIES Measures: 9.25 x 5.91 x 2.40” MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inches [mm] 2. Tolerance 0.02 [0.5] maximum 3. Input connector P1 is Dinkle terminal P/N DT-4C-B01W-03, with nickel plated M3.5 screws or equivalent. 4. Output connectors P2 and P3 are for M5*0.8 screw connections. 5. Output connector P4 is Molex header 22-05-7105 or equivalent, mating with Molex housing 50-37-5103 or equivalent. 6. Weight: 2.884 Kgs (6.35 lbs.) approx. for enclosed form. 7. Maximum penetration depth of fixing screws is 4 mm from the outer surface of chassis. PIN CHART Connector P1 (AC) P2 P3 PIN NO. 1 2 3 1 2 1 2 Polarity Live Neutral Ground +V1 V1 Return Connector P4 PIN NO. 1 2 3 4 5 6 7 8 9 10 common +5V FAN Polarity +V1 Sense -V1 Sense PFD Inhibit DC OK PS OFF +12V FAN Return Standby Return 2 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-pm1100-power-supply.html h t t p: / / pow e r. sa ge r. c om