PROTEK PM301 SERIES 300 WATT MEDICAL & ITE POWER SUPPLIES 300 Watt Open Frame Power Supply Measures: 3.00 x 6.00 x 1.50” DESCRIPTION PM301 SERIES The PM301 series of AC-DC switching power supplies in a package of 3 x 6 x 1.5 inches are capable of delivering 300 RoHS watts of continuous power at 10 CFM forced air cooling or 200 watts at convection cooling. A L-bracket or cover-and-fan assembly can be added during manufacturing. They are specially certified for IEC /EN /UL /CSA 60601-1 for medical applications, but not for life-supporting equipment. The units are design also to IEC /EN /UL /CSA 60950-1 and suitable for data networking, computer and telecommunication applications. FEATURES  BF Class insulation  Operation up to 5000 meters  3 x 6 inch footprint with 1.5 inch low profile  100-240 VAC input with active PFC  Less than 220 μA leakage current  Meet EN55011 /55022 and FCC Class B SAFETY STANDARD APPROVAL  Power Factor 0.98 typical  100% burn-in at full load (Pending)  Short -circuit protection  Power Fail Detect (PFD) signal  Inhibit - TTL high to disable output  Compliant with RoHS requirements  High Efficiency 92% typical  Power consumption in standby mode less than 1 W at standby power 5 V /100 mA GENERAL SPECIFICATIONS INPUT SPECIFICATIONS Switching frequency: 100 KHz (typical) Input voltage: 90-264 VAC Efficiency: 87% minimum on all models Input frequency: 47-63 Hz Turn on delay time 3 s maximum at 100 VAC Input current: 4.0 A (rms) for 115 VAC Hold-up time: 10 ms minimum at 110 VAC 2.0 A (rms) for 230 VAC Line regulation: ±0.5% maximum at full load Earth leakage current: 220 μA max. @ 264 VAC, 63 Hz Inrush current: 20 A @ 115 VAC or 40 A @ 230 VAC, at 25℃ Touch current: 100 μA max. @ 264 VAC, 63 Hz cold start Withstand voltage: 4000 VAC from input to output (2MOPP) OUTPUT SPECIFICATIONS 1500 VAC from input to ground (1 MOPP) Output voltage/current: See rating chart. 1500 VAC from output to ground Total output power: See rating chart. MTBF: 250,000 hours at full load at 25℃ ambient, Ripple and noise: 1% peak to peak maximum calculated per MIL-HDBK-217F Overvoltage protection: Set at 112-140% of its nominal output EMC Performance voltage EN55011/EN55022: Class B conducted, class B radiated Overcurrent protection: Output protected to short circuit conditions FCC: Class B conducted, class B radiated Temperature coefficient: All outputs ±0.04% /℃ maximum VCCI: Class B conducted, class B radiated Transient response: Maximum excursion of 4% or better on all EN61000-3-2: Harmonic distortion, class A and D models, recovering to 1% of final value EN61000-3-3: Line flicker within 500 us after a 25% step load EN61000-4-2: ESD, ±8 KV air and ±6 KV contact change EN61000-4-3: Radiated immunity, 3 V/m Fan power: 12 V at 1.0 A maximum (isolated) EN61000-4-4: Fast transient/burst, ±2 KV Standby power: 5 V at 2.0 A maximum or 12 V at 1.0 A EN61000-4-5: Surge, ±1 KV diff., ±2 KV com maximum EN61000-4-6: Conducted immunity, 3 Vrms EN61000-4-8: Magnetic field immunity, 3 A/m ENVIRONMENTAL SPECIFICATIONS EN61000-4-11: Voltage dip immunity, 30% reduction for Operating temperature: 0℃to +70℃ Storage temperature: -40℃to +85℃ 500 ms, 60% reduction for 100 ms, >95% Relative humidity: 5% to 95% non-condensing reduction for 10 ms Derating: Derate from 100% at +50℃ linearly to 50% at +70℃, applicable to convection and forced-air cooling conditions 25 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PM301-power-supply.html h t t p: / / pow e r. sa ge r. c om PROTEK PM301 SERIES UNIVERSAL INPUT PM301 MEDICAL & ITE SERIES 300 Watt Open Frame Power Supply Measures: 3.00 x 6.00 x 1.50” INTERFACE SIGNALS OUTPUT POWER DERATING CURVE PFD: TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1ms prior to V1 output dropping 5% below its nominal value. This signal also provides a minimum delay of 100 ms after V1 is within regulation. Inhibit: Requires an external TTL high level signal to inhibit outputs for standard models OUTPUT VOLTAGE/CURRENT RATING CHART Output Efficiency (typical) Min. Max. Current Max. Current Ripple & @ 200 W @ 300 W (1) (3) (2) (2) (4) Model V1 Current at convection at 10 CFM Tol. Noise Max. Power 115/230 Vac 115/230 Vac PM301-12A 12 V 0 A 16.67 A 25.00 A ±2% 120 mV 200 /300 W 89 /91% 88 /90% PM301-13A 15 V 0 A 13.34 A 20.00 A ±2% 150 mV 200 /300 W 89 /92% 88 /91% PM301-13-2A 19 V 0 A 10.53 A 15.80 A ±2% 190 mV 200 /300 W 89 /91% 88 /90% PM301-14A 24 V 0 A 8.34 A 12.50 A ±2% 240 mV 200 /300 W 89 /92% 88 /91% PM301-16A 30 V 0 A 6.67 A 10.00 A ±2% 300 mV 200 /300 W 89 /92% 88 /91% PM301-17A 36 V 0 A 5.56 A 8.34 A ±2% 360 mV 200 /300 W 89 /92% 88 /91% PM301-18A 48 V 0 A 4.17 A 6.25 A ±2% 480 mV 200 /300 W 89 /92% 88 /91% NOTES: 1. Suffix “A” in model numbers denotes PCB constructed form. Change suffix “A” to “B” for L-bracket form, e.g. PM301-14B. Change “B” to “C” for enclosed from with cover and fan assembly, e.g. PM301-14C. 2. 200 W without moving air or 300 W with 10 CFM forced air provided by user for “A” and “B” version, 300 W for “C” version with cover and fan assembly. 3. Standby power output 5 V at 2 A. Add suffix “-12” for standby power output 12 V at 1.0 A, e.g. PM301-12A-12 4. Ripple and noise is maximum peak to peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 10 μF tantalum capacitor in parallel with a 0.1 μF ceramic capacitor across the output. MECHANICAL SPECIFICATIONS PCB constructed Form 26 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PM301-power-supply.html h t t p: / / pow e r. sa ge r. c om PROTEK PM301 SERIES 300 Watt Open Frame Power Supply UNIVERSAL INPUT PM301 MEDICAL & ITE SERIES Measures: 3.00 x 6.00 x 1.50” MECHANICAL SPECIFICATIONS L-bracket Form Enclosed Form NOTES: 1. Dimensions shown in inches [mm] 2. Tolerance 0.02 [0.5] maximum 3. Input connector P1 is Dinkle DT-35-B01W-03 with M3, nickel-plated screws. 4. Output connector P2 and P3: M3 x 0.5 screw connections 5. Fan connector P4: Molex header 22-04-1021 or equivalent, mating with Molex housing 22-01-1022 or equivalent. 6. Connectors P5: Molex header 22-04-1061 or equivalent, mating with Molex housing 22-01-1062 or equivalent. 7. Option output connector P7: Molex header 39-30-1180 or equivalent, mating with Molex housing 39-01-2185 or equivalent. 8. Option input connector P8: Molex header 26-60-4050 or equivalent, mating with Molex housing 09-50-8050 or equivalent. 9. Weight: 510 grams (1.12 lbs.) approx. for PCB form, 612 grams (1.35 lbs.) approx. for L-bracket form, 744 grams (1.64 lbs.) approx. for enclosed form. 10. Maximum penetration depth of fixing screws is 4 mm from the outer surface of chassis. 27 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PM301-power-supply.html h t t p: / / pow e r. sa ge r. c om PROTEK PM301 SERIES UNIVERSAL INPUT PM301 MEDICAL & ITE SERIES 300 Watt Open Frame Power Supply Measures: 3.00 x 6.00 x 1.50” PIN CHART Connector P1, P8 P4 P2 P3 PIN NO. 1 2 3 1 2 Common +12V Fan Fan Return Polarity Live Neutral Ground +V1 Return (isolated) (isolated) Connector P5 PIN NO. 1 2 3 4 5 6 +5V/+12V Common Polarity -Sense +Sense PFD Inhibit Standby Return Connector P7 PIN NO. 1 2 3 4 5 6 7 8 9 +5V/+12V Fan Polarity Inhibit +V1 +V1 +V1 +V1 +V1 +V1 Standby Return PIN NO. 10 11 12 13 14 15 16 17 18 Standby Common Common Common Common Common Common +12V Polarity PFD Return Return Return Return Return Return Return Fan 28 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PM301-power-supply.html h t t p: / / pow e r. sa ge r. c om