PROTEK PM400C SERIES 400 Watt Enclosed with Fan Power Supply 400 WATT MEDICAL & ITE POWER SUPPLIES Measures: 7.00 x 4.00 x 1.50”” DESCRIPTION PM400 SERIES The PM400 series of AC-DC switching power supplies in a package of 4 x 7 x 1.58 inches are capable of delivering 400 watts of continuous power at 7 CFM forced air cooling or 300 RoHS watts at convection cooling. The units are constructed on a printed circuit board with a U-bracket for mechanical support and heat sinking. A cover and fan assembly can be added during manufacturing for 400 watt output without the change of any dimension. They are designed for medical applications, but not for life-supporting equipment. The units are certified also to IEC/EN/UL 60950-1 and suitable for data networking, computer and telecommunication applications. SAFETY STANDARD APPROVALS FEATURES  BF Class insulation UL ES 60601-1, CSA C22.2 No. 60601-1 File No. E178020  Operation up to 5000 meters  100-240 VAC input with active PFC  Less than 300 μA leakage current TÜV EN 60601-1  Standby output 5VDC at 100mA  EN55011 / 55022 Class B conducted emissions  Inhibit - TTL low to disable output UL 60950-1, CSA C22.2 No. 60950-1  Standard PS Off and DC OK signals  Efficiency greater than 88%  Compliant with RoHS requirements TÜV EN 60950-1 INPUT SPECIFICATIONS Input voltage: 90-264 VAC GENERAL SPECIFICATIONS Input frequency: 47-63 Hz Input current: 4.2 A (rms) @115 VAC, 60 Hz Switching frequency: 85 KHz (typical) 2.1 A (rms) @ 230 VAC, 50 Hz Efficiency: Typical 89% @ 115 VAC, 92% @ 230 VAC Earth leakage current: 300 μA max. @ 264 VAC, 63 Hz Hold-up time: 12 ms minimum at 110 VAC & 400 W Line regulation: ±0.5% maximum at full load OUTPUT SPECIFICATIONS Inrush current: 20 A @ 115 VAC, or 40 A @ 230 VAC, at Output voltage/current: See rating chart. 25℃ cold start Maximum output power: See rating chart. Withstand voltage: 4000 VAC from input to output (2 MOPP) Ripple and noise: 1% peak to peak maximum 1500 VAC from input to ground (1 MOPP) Remote sense Compensation for cable losses up to 0.5 V 1500 VAC from output to ground Overvoltage protection: Set at 115-140% of nominal output voltage MTBF: 350,000 hours at full load at 25℃ ambient, calculated per MIL-HDBK-217F Overcurrent protection: Protected to output short circuit conditions Thermal shutdown Protected to overtemperature conditions EMC Performance Temperature coefficient: All outputs ±0.04% /℃ maximum EN55011/EN55022: Class B conducted, class A radiated Transient response: Maximum excursion of 4%, recovering to FCC: Class B conducted, class A radiated 1% of final value within 500 us after a 25% VCCI: Class B conducted, class A radiated step load change EN61000-3-2: Harmonic distortion, class A and D Standby power 5 V at 100 mA maximum EN61000-3-3: Line flicker Fan power 12 V at 250 mA maximum EN61000-4-2: ESD, ±8 KV air and ±6 KV contact EN61000-4-3: Radiated immunity, 3 V/m EN61000-4-4: Fast transient/burst, ±2 KV ENVIRONMENTAL SPECIFICATIONS EN61000-4-5: Surge, ±1 KV diff., ±2 KV com Operating temperature: -10℃ to +70℃ EN61000-4-6: Conducted immunity, 3 Vrms Storage temperature: -40℃ to +85℃ EN61000-4-8: Magnetic field immunity, 3 A/m Relative humidity: 5% to 95% non-condensing EN61000-4-11: Voltage dip immunity, 30% reduction for Derating: Derate from 100% at +50℃ linearly to 500 ms, 60% reduction for 100 ms and >95% 50% at +70℃, applicable to convection reduction for 10 ms and forced-air cooling conditions Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PM400C-power-supply.html h t t p: / / pow e r. sa ge r. c om 29 PROTEK PM400C SERIES 400 Watt Enclosed with Fan Power Supply UNIVERSAL INPUT PM400 MEDICAL & ITE SERIES Measures: 7.00 x 4.00 x 1.50”” INTERFACE SIGNALS OUTPUT POWER DERATING CURVE PFD: TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1 ms prior to master output dropping 5% below its nominal value. This signal also provides a minimum delay of 100 ms after master output is within regulation. Inhibit: TTL low to turn off output DC OK: TTL high when output voltage >95% PS OFF: TTL high to turn off output OUTPUT VOLTAGE/CURRENT RATING CHART Output Efficiency (typical) Min. Max. Current Max. Current Ripple & Max. Output @ 300 W @ 400 W (1) (4) (2) (3) Model V1 Current at convection at 7 CFM Tol. Noise Power 115/230 Vac 115/230 Vac PM400-12B 12 V 0.1 A 25.00 A 33.34 A ±2% 120 mV 300 W /400 W 90 /92% 88 /91% PM400-13B 15 V 0.1 A 20.00 A 26.67 A ±2% 150 mV 300 W /400 W 90 /92% 88 /91% PM400-13-1B 18 V 0.1 A 16.67 A 22.23 A ±2% 180 mV 300 W /400 W 90 /92% 88 /91% PM400-14B 24 V 0.1 A 12.50 A 16.67 A ±2% 240 mV 300 W /400 W 90 /92% 89 /92% PM400-15B 28 V 0.1 A 10.72 A 14.29 A ±2% 280 mV 300 W /400 W 90 /92% 89 /92% PM400-17B 36 V 0.1 A 8.34 A 11.12 A ±2% 360 mV 300 W /400 W 90 /92% 89 /92% PM400-18B 48 V 0.1 A 6.25 A 8.34 A ±2% 480 mV 300 W /400 W 90 /92% 90 /92% NOTES: 1. Change suffix “B” for U-Bracket form to “C” for enclosed form with cover and fan assembly, e.g. PM400-14C. 2. 300 W without moving air or 400 W with 7 CFM forced air provided by user for “B” version, 400 W for “C” version with cover and fan assembly 3. Ripple and noise is maximum peak to peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 10 μF tantalum capacitor in parallel with a 0.1 μF ceramic capacitor across the output. 4. All models may be operated at no-load without damage. At no load, output voltage fluctuates beyond 5% due to the burst-mode operation of the control IC in them for energy saving. MECHANICAL SPECIFICATIONS U-bracket Form Enclosed Form NOTES: 1. Dimensions shown in inches [mm] 2. Tolerance 0.02 [0.5] maximum 3. Input connector P1 is Dinkle terminal P/N DT-35-B01W-03, with nickel plated M3 screws. 4. P2, P3: M4 x 0.7 screw connectors 5. Connector P4: Molex header 87833-08 or equivalent, mating with Molex housing 51110-0850 or equivalent. 6. Fan connector P5: JST header S2B-ZR-3.4 or equivalent, mating with JST housing ZHR-2 or equivalent. 7. Weight: 1.0 Kg (2.23 lbs.) approx. for U-bracket form, 1.14 Kgs. (2.52 lbs.) approx. for enclosed form 8. Maximum penetration depth of fixing screws is 4 mm from the outer surface of chassis. Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. 30 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PM400C-power-supply.html h t t p: / / pow e r. sa ge r. c om PROTEK PM400C SERIES 400 Watt Enclosed with Fan Power Supply UNIVERSAL INPUT PM400 MEDICAL & ITE SERIES Measures: 7.00 x 4.00 x 1.50”” PIN CHART CONN P1 (AC) P5 P2 P3 PIN MODEL 1 2 3 1 2 PM400-12B PM400-15B PM400-13B PM400-17B Common +12V Common Ground Live Neutral +V1 PM400-13-1B PM400-18B Return Fan Return PM400-14B CONN P4 PIN MODEL 1 2 3 4 5 6 7 8 PM400-12B PM400-15B PM400-13B PM400-17B Common +5V +V1 Sense -V1 Sense PFD Inhibit DC OK PS OFF PM400-13-1B PM400-18B Return Standby PM400-14B Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PM400C-power-supply.html h t t p: / / pow e r. sa ge r. c om 31