PROTEK POWER PUP220-18

PROTEK PUP220 SERIES 220 WATT SWITCHING POWER SUPPLIES 220 Watt External Power Supply Measures: 7.76 x 3.46 x 1.73” DESCRIPTION PUP220 SERIES (LVD) The PUP220 series of AC/DC switching power supplies are for 220 watts of continuous output power. They are RoHS enclosed in a 94V-1 rated polyphenylene-oxide case with an IEC320/C14 inlet to mate with interchangeable cord for world-wide use. All models meet CISPR 22 and FCC class B emission limits, and comply with UL, TUV and CE requirement. FEATURES z High Efficiency z Overvoltage protection z Short-circuit protection z Overpower protection SAFETY STANDARD APPROVALS z Over temperature protection z Compliant with CEC and Energy Star Efficiency UL 60950-1, CSA C22.2 No. 60950-1 level V requirements * No load power consumption less than 0.5 W * Average active efficiency ≧ 87% TUV EN60950-1 z Compliant with RoHS requirement INPUT SPECIFICATIONS Input voltage: 90-264 VAC GENERAL SPECIFICATIONS Input frequency: 50-60 Hz Hold-up time: 5 ms minimum at 110 VAC or 240 VAC Input current: 3 A (rms) for 100 VAC Efficiency: 87% minimum at full load 1.3 A (rms) for 240 VAC Turn on delay time: 3 seconds maximum at 110 VAC Touch current: 250 μA max. @ 264 VAC, 60 Hz Inrush current: No damage Withstand voltage: 1500 VAC from input to output and ground MTBF: 100,000 hours at full load at 25℃ ambient, OUTPUT SPECIFICATIONS calculated per MIL-HDBK-217F Output voltage/current: See rating chart. Total output power: See rating chart. Ripple and noise: 380 mV peak to peak maximum EMC Performance (EN55022) Overvoltage protection: set at 112-145% of its nominal output EN55022: Class B conducted, class B radiated voltage. FCC: Class B conducted, class B radiated Overcurrent protection: All models protected to short circuit VCCI: Class B conducted, class B radiated conditions EN61000-3-2: Harmonic distortion, class D Temperature coefficient: All outputs ±0.04% /℃ maximum EN61000-3-3: Line flicker Transient response: Maximum excursion of 4% or better on all EN61000-4-2: ESD, ±15 KV air and ±8 KV contact models, recovering to 1% of final value EN61000-4-3: Radiated immunity, 3 V/m within 500 us after a 25% step load EN61000-4-4: Fast transient/burst, ±1 KV change EN61000-4-5: Surge, ±1 KV diff., ±2 KV com EN61000-4-6: Conducted immunity, 3 Vrms EN61000-4-8: Magnetic field immunity, 1 A/m EN61000-4-11: Voltage dip immunity, ENVIRONMENTAL SPECIFICATIONS 30% reduction for 500 ms Operating temperature: 0℃ to +40℃ >95% reduction for 10 ms Storage temperature: -20℃ to +80℃ Relative humidity: 10% to 90% non-condensing Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PUP220-power-supply.html 73 h t t p: / / pow e r. sa ge r. c om PROTEK PUP220 SERIES UNIVERSAL INPUT PUP220 SERIES 220 Watt External Power Supply Measures: 7.76 x 3.46 x 1.73” OUTPUT VOLTAGE/CURRENT RATING CHART Output Average Active efficiency (typical) Ripple & (2) (1) Model V1 Min. Current Max. Current Tol. Noise Max. Power @ 115 / 230 Vac PUP220-12 12 V 0 A 15.00 A 5% 380 mV 180 W 88 / 90 % PUP220S-12 12 V 0 A 15.00 A 5% 380 mV 180 W 88 / 90 % PUP220-13-2 19 V 0 A 11.57 A 5% 380 mV 220 W 90 / 92 % PUP220-14 24 V 0 A 9.16 A 5% 380 mV 220 W 88 / 90 % PUP220-18 48 V 0 A 4.58 A 5% 480 mV 220 W 92 / 93 % NOTES: 1. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 47 μF electrolytic capacitor in parallel with a 0.1 μF ceramic capacitor across the output. 2. PUP220 models are equipped with IEC320/C14 inlet, and PUP220S models with IEC320/C6 inlet. MECHANICAL SPECIFICATIONS For PUP220-12 and PUP220S-12 only NOTES: 1. Dimensions shown in inches [mm] 2. Tolerance 0.02 [0.5] maximum 3. Weight: 1.0 Kg (2.2 lbs.) approx. 4. The length of output cable for PUP220-13-2 is 37.4 [950.0] 5. Output connector for PUP220-12 and PUP220S-12 is 4-pin plug without lock (molding type), mating with 4-pin socket, Kycon P/N KPJX-4S-S or equivalent. 6. Output connector for PUP120-13-2, PUP220-14 and PUP220-18 is Molex Mini - Fit receptacle, P/N: 39-01-2060 with female terminal #5556 or equivalent, mating with Molex plug 39-01-2066 and male terminal #5558 or equivalent. It also mates with Molex headers #5566, #5569, or equivalent. PIN CHART PIN PIN SHELL OF 1 2 3 4 1 2 3 4 5 6 CONNECTOR MODEL MODEL PUP220-13-2 PUP220-12 V1 Return & V1 Return & +V1 PUP220-14 +V1 AC Ground AC Ground PUP220S-12 PUP220-18 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. 74 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/protek-PUP220-power-supply.html h t t p: / / pow e r. sa ge r. c om