PULSE P1166.103NLT
Specifications
Manufacturer
Pulse
Manufacturers Part #
P1166.103NLT
Industry Aliases
P1166.103NLT
Sub-Category
Surface Mount Inductors
Selling Alternatives
P1166.103T
Packaging
Tape and Reel
Factory Pack Quantity
1200
Datasheet
Extracted Text
SMT Power Inductors Shielded Drum Core - P1166NL Series Height: 3.8mm Max Footprint: 7.5mm x 7.5mm Max Current Rating: up to 5.5A Inductance Range: .44µH to 750µH Electrical Specifications @ 25°C - Operating Temperature -40°C to +130°C DCR (mΩ) 7 8 6 Inductance Inductance Saturation Heating Core Loss 5 2, 3 Part @ 0ADC @ Irated Irated Current Current Factor SRF Number (μH ±20%) (μH) MIN (ADC) TYP MAX -25% (A) +40°C (A) (K2) (MHz) P1166.681NL ** 0.68* 0.44 5.5 5.0 6.0 5.9 5.5 380 >40 P1166.102NL 1.00* 0.65 4.9 6.2 7.5 5.2 4.9 440 >40 P1166.162NL 1.60* 1.0 4.0 7.8 11 4.0 4.4 570 >40 P1166.302NL 3.00* 2.0 2.8 19 23 3.0 2.8 780 >40 P1166.482NL 4.80* 3.1 2.4 25 31 2.4 2.5 990 >40 P1166.682NL 6.80* 4.4 2.1 32 40 2.1 2.2 1200 38 P1166.103NL 10 7.5 1.6 58 70 1.8 1.6 1400 29 P1166.123NL ** 12 9.0 1.5 62 78 1.7 1.5 1500 25 P1166.153NL ** 15 11.3 1.4 74 92 1.5 1.4 1700 22 P1166.183NL ** 18 13.5 1.2 100 124 1.4 1.2 1800 21 P1166.223NL 22 16.5 1.2 106 126 1.2 1.2 2000 20 P1166.273NL ** 27 20.3 1.0 146 180 1.1 1.0 2300 17 P1166.333NL ** 33 24.8 0.94 167 205 1.0 0.94 2400 15 P1166.393NL ** 39 29.3 0.86 183 211 0.86 0.90 2700 13 P1166.473NL 47 35.3 0.83 206 260 0.83 0.85 2900 12 P1166.563NL ** 56 42.0 0.73 271 340 0.73 0.74 3300 11 P1166.683NL ** 68 51.0 0.67 303 370 0.67 0.70 3600 9.5 P1166.823NL ** 82 61.5 0.60 411 500 0.61 0.60 4000 8.0 P1166.104NL 100 75.0 0.56 464 580 0.56 0.57 4300 7.5 P1166.124NL ** 120 90.0 0.53 528 645 0.55 0.53 4700 7.0 P1166.154NL 150 113 0.46 695 860 0.46 0.46 5300 6.3 P1166.184NL ** 180 135 0.39 992 1190 0.42 0.39 5800 5.6 P1166.224NL 220 165 0.35 1210 1480 0.37 0.35 6400 5.1 P1166.274NL ** 270 203 0.32 1407 1750 0.32 0.33 7100 4.6 P1166.334NL 330 248 0.31 1580 1880 0.31 0.31 7800 4.1 P1166.394NL ** 390 293 0.26 2178 2600 0.29 0.26 8500 3.9 P1166.474NL ** 470 353 0.25 2400 2910 0.26 0.25 9500 3.6 P1166.564NL ** 560 420 0.23 2705 3400 0.23 0.23 10000 3.1 P1166.684NL ** 680 510 0.20 3658 4450 0.21 0.20 11000 2.7 P1166.824NL 820 615 0.17 5021 6200 0.20 0.17 13000 2.5 P1166.105NL 1000 750 0.15 6720 8000 0.16 0.15 14000 1.3 * Inductance is at 0ADC tolerance on indicated part numbers is ±30%; tolerance is ±20% on all other parts. NOTES FROM TABLE: (See page 43) ** Contact Pulse for availability http://www.power.pulseelectronics.com/contact power.pulseelectronics.com SMP2007 (07/17) 34 SMT Power Inductors Shielded Drum Core - P1166NL Series Mechanical Schematic P1166.XXXNL Inches Weight .....................0.7 grams Dimensions: mm Tape & Reel ..............1200/reel Unless otherwise specified, .010 all tolerances are ± 0,25 (pages 27 - 42) Notes from Tables: 7. In high volt*time (Et) or ripple current applications, additional heating in the 1. Unless otherwise specified, all testing is made at 100kHz, 0.1VAC. component can occur due to core losses in the inductor which may necessitate 2. Optional Tape & Reel packaging can be ordered by adding a “T” derating the current in order to limit the temperature rise of the component. In suffix to the part number (i.e P1166.102NL becomes P1166.102NLT). order to determine the approximate total loss (or temperature rise) for a given Pulse complies with industry standard Tape and Tape & Reel application, both copper losses and core losses should be taken into account. specification EIA481. 3. The “NL” suffix indicates an RoHS-compliant part numer. Non-NL Estimated Temperature Rise: suffixed parts are not necessarily RoHS compliant, but are electrically and mechanically equivalent to NL versions. If a part number does not .833 Trise = [Total loss (mW) / K0] (°C) have the “NL” version, but an RoHS compliant version is required, please contact Pulse for availability. Total Loss = Copper loss + Core loss (mW) 4. Temperature of the component (ambient plus temperature rise) must be 2 Copper loss = IRMS x DCR (Typical) (mW) within specified operating temperature range. 1/2 2 2 5. The rated current (Irated) as listed is either the saturation current or the Irms = [IDC + ΔI /12] (A) heating current depending on which value is lower. 2.38 1.23 Core loss = K1 x f (kHz) x Bac (Ga) (mW) 6. The saturation current, Isat, is the current at which the component inductance drops by the indicated percentage (typical) at an ambient temperature of 25C. Bac (peak to peak flux density) = K2 x ΔI (Ga) This current is determined by placing the component in the specified ambient [= K2/L (μH) x Et (V-μSec) (Ga)] environment and applying a short duration pulse current (to eliminate self- where f varies between 25kHz and 1MHz, and Bac is heating effects) to the component. less than 2500 Gauss. 7. The heating current, Idc, is the DC current required to raise the component K2 is a core size and winding dependent value and is temperature by the indicated delta (approximately). The heating current is given for each p/n in the proceeding datasheets. K0 & determined by mounting the component on a typical PCB and applying K1 are platform and material dependant constants and current for 30 minutes. The temperature is measured by placing the are given in the table below for each platform. thermocouple on top of the unit under test. http://www.power.pulseelectronics.com/contact power.pulseelectronics.com SMP2007 (07/17) 43 SMT Power Inductors Shielded Drum Core - P1166NL Series Trise Factor Core Loss Factor Part No. (KO) (K1) PG0085/86 2.3 5.29E-10 PG0087 5.8 15.2E-10 PG0040/41 0.8 2.80E-10 P1174 0.8 6.47E-10 PF0601 4.6 14.0E-10 PF0464 3.6 24.7E-10 PF0465 3.6 33.4E-10 P1166 1.9 29.6E-10 P1167 2.1 42.2E-10 PF0560NL 5.5 136E-10 P1168/69 4.8 184E-10 P1170/71 4.3 201E-10 P1172/73 5.6 411E-10 PF0552NL 8.3 201E-10 PF0553NL 7.1 411E-10 Take note that the component’s temperature rise varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. http://www.power.pulseelectronics.com/contact power.pulseelectronics.com SMP2007 (07/17) 44
Frequently asked questions
How does Electronics Finder differ from its competitors?

Is there a warranty for the P1166.103NLT?

Which carrier will Electronics Finder use to ship my parts?

Can I buy parts from Electronics Finder if I am outside the USA?

Which payment methods does Electronics Finder accept?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods