PULSE PA2607.301NLT

SMT Power Inductor Power Beads - PA2607NL and PA2607AHL Series Current Rating: Over 90Apk Inductance Range: 115nH to 300nH Height: 7.5mm and 7.6mm Max Footprint: 10.4mm x 7.9mm Max Halogen Free 7 Electrical Specifications @ 25°C — Operating Temperature -40°C to +130°C 4 1 Inductance Saturation Current Inductance Height 2 3 Part Irated DCR Heating Current (A TYP) @ 0ADC @Irated mm* (ADC) (mΩ nominal) (A TYP) Number (nH +/- 15%) (nH TYP) (inches) 25°C 100°C PA2607.121NL 115 115 41 94 80 7.4* PA2607.151NL 150 150 41 72 61 (.291) PA2607.181NL 175 175 41 62 53 0.29 +/- 7% (.XXNL) PA2607.211NL 215 195 41 48 41 41 0.29 +/- 5% (.XXXAHL) 7.3* PA2607.231NL 230 208 37 43 37 PA2607.271NL 270 241 31 37 34 (.287) PA2607.301NL 300 260 27 32 28 NOTES: 1. Inductance measured at 100kHz, 1Vrms @25°C. 5. The heating current is the DC current which causes the part temperature to increase by approximately 40°C. 2. The rated current as listed is either the saturation current or the heating current depending on which value is lower. 6. In high volt*time applications, additional heating in the component can occur due to core losses in the inductor which may neccessitate derat- 3. The nominal DCR is measured from point a to point b , as shown below ing the current in order to limit the temperature rise of the component. To on the mechanical drawing. The standard part (PA2607.XXXNL) has determine the approximate total losses (or temperature rise) for a given a DCR tolerance of +/-7%. A tighter DCR tolerance of +/-5% is avail- application, the coreloss and temperature rise curves can be used. able by changing the NL suffix to AHL (i.e. PA2607.211NL becomes PA2607.211AHL). 7. Optional Tape & Reel packaging can be ordered by adding a “T” suf- fix to the part number (i.e. PA2607.211NL becomes PA2607.211NLT). 4. The saturation current is the typical current which causes the induc- Pulse complies to industry standard tape and reel specification EIA481. tance to drop by 20% at the stated ambient temperatures (25°C and The tape and reel for this product has a width (W=24mm), pitch 100°C). This current is determined by placing the component in the (Po=16.0mm) and depth (Ko=7.6mm). specified ambient environment and applying a short duration pulse current 8. The temperature of the component (ambient plus temperature rise) must (to eliminate self-heating effects) to the component. be within the stated operating temperature range. Mechanical Schematic PA2607.XXXNL  PA2607 .XXXNL  D/C CTRY * Please note that marking shown is for the PA2607.XXXNL parts. Marking for AHL parts is the same except PA2607.XXXNL is replaced by PA2607.XXXAHL. Weight ...........2.4 grams .008 0.2 Tape & Reel ........ 400/reel Inches Dimensions: mm Unless otherwise specified, .010 all tolerances are ± 0,25 http://www.power.pulseelectronics.com/contact power.pulseelectronics.com P673.H (07/17) 1 SMT Power Inductor Power Beads - PA2607NL and PA2607AHL Series http://www.power.pulseelectronics.com/contact power.pulseelectronics.com P673.H (07/17) 2 SMT Power Inductor Power Beads - PA2607NL and PA2607AHL Series B 0.37 http://www.power.pulseelectronics.com/contact power.pulseelectronics.com P673.H (07/17) 3