THT Power Inductors Toroid - Vertical, Low Profile and Klipmount™ Available in vertical, low profile and Klipmount™ SMPS averaging filter Characterized for general purpose use and ripple filters Single-layer designs 3 Can be used as differential mode inductors in EMI filters Electrical Specifications @ 25°C - O perating Temperature -40°C to 130°C Reference Operating Values Design Control Values 6 5 1 4 Vertical Low Profile Inductance IDC ET Energy Inductance 20 kHz DCR Coil Klip* Lead OP Part Part Typical (AMPS) (V-µSec) Storage No DC (µH) Test mV (Ω MAX) Size Mount Diameter Number Number (µH) (µJ) (±20%) No DC Code Package (in ± .003) PE-51591NL 20 2.0 52 40 32.8 33 .060 H .020 PE-92100NL 25 2.6 30 85 20.7 22 .043 A KM1 .020 PE-92101NL PE-92401NL 50 2.6 50 169 45.7 45 .071 B KM2 .020 PE-92102NL PE-92402NL 100 2.6 90 338 94.1 90 .100 C KM3 .020 PE-92103NL 35 2.6 55 118 28.4 36 .037 B KM2 .025 PE-92104NL PE-92404NL 70 3.0 85 315 61.0 73 .052 C KM3 .025 PE-92105NL PE-92405NL 145 3.0 140 653 141.8 140 .087 D KM4 .025 PE-92106NL 285 3.0 300 1283 264.1 340 .140 E KM5 .025 PE-92107NL 450 3.0 425 2025 436.3 500 .200 F .025 PE-92108NL PE-92408NL 67 3.6 130 648 90.7 110 .045 D KM4 .032 PE-92109NL 165 4.0 240 1320 152.0 260 .070 E KM5 .032 PE-92110NL 270 4.0 350 2160 263.9 400 .100 F .032 PE-92111NL 40 4.0 70 320 37.9 57 .027 C KM3 .032 PE-51590NL 22 5.0 44 275 20.3 37 .020 G .032 PE-92112NL PE-92412NL 100 5.0 200 1250 90.7 180 .034 E KM5 .042 PE-92113NL 170 5.0 300 2125 159.7 310 .050 F .042 PE-92114NL PE-92414NL 35.6 5.0 100 688 55.6 88 .023 D KM4 .042 PE-92115NL 95 7.0 225 2328 96.0 200 .025 F .051 PE-92116NL PE-92416NL 55 7.0 150 1348 49.1 100 .017 E KM5 .051 PE-92117NL 55 10.0 175 2750 55.9 120 .013 F .064 * Parts available with KlipMount option can be ordered by adding a “K” suffix to the part number (i.e. PE-92100K). 1 pulseelectronics.com P635.B (02/15) THT Power Inductors Toroid - Vertical, Low Profile and Klipmount™ Relationships Between Reference and Operating Conditions Inductance vs. Operating ET (at reference I ) DC Max. Operating ET vs. Frequency (at reference I ) DC 2.00 2.00 2.00 1.75 Temp. Rise 1.75 >40°C 1.75 1.50 Temp. Rise 1.50 >40°C 1.50 1.25 1.25 1.25 1.00 1.00 1.00 .75 .75 .75 .50 .50 .50 .25 .25 .25 0 .25 .50 .75 1.00 1.25 1.50 0 .25 .50 .75 1.00 1.25 1.50 OPERATING DC CURRENT 02030405060708090 100 REFERENCE I DC OPERATING ET OPERATING FREQUENCY — kHz REFERENCE ET Mechanical Schematic Klipmount™ Package • Base material meets flammability requirements of UL 94V-0 • Mechanically rigid mount • PC Board - automatic insertability 1 • Lowest cost C A B C D H EV) Standard 2 Typical Package Maximum .130 .020 ± 3,30,508 .340 .580 .650 .29 .110 KM-1 8,64 14,73 16,51 7,37 2,79 E D .450 .650 .700 .325 .150 2E KM-2 B 11,43 16,51 17,78 8,26 3,81 A .450 .850 .950 .415 .150 KM-3 11,43 21,59 24,13 10,54 3,81 .620 .970 1.10 .475 .225 KM-4 15,50 24,64 27,94 12,07 5,72 .700 1.30 1.40 .625 .250 KM-5 17,78 33,02 35,56 15,88 6,35 Note: Units with large wire sizes may exceed B dimension. KLIPMOUNT™ is a trademark of Pulse Engineering, Inc. Inches .010 Dimensions: Unless otherwise specified, all tolerances are ± mm 0,25 2 pulseelectronics.com P635.B (02/15) INDUCTANCE AT OPERATING I DC REFERENCE I DC INDUCTANCE AT OPERATING ET INDUCTANCE AT REFERENCE ET OPERATING ET FOR 40°C TEMP. RISE REFERENCE ET THT Power Inductors Toroid - Vertical, Low Profile and Klipmount™ (continued) Mechanicals Vertical and Low Profile Package Vertical Package P N L M K Size Code (MAX) (MAX) (+.125/-.025) P .550 .250 .375 .180 A 13,97 6,35 9,53 4,57 .700 .380 .375 .280 .530 .050 ± L B 17,78 9,65 9,53 7,11 13,46 1,27 .850 .410 .375 .280 .720 .050 ± M C 21,59 10,41 9,53 7,11 18,29 1,27 Low Profile Package N 1.050 .550 .375 .400 .840 .020 ± D 26,67 13,97 9,53 10,16 21,24 0,51 1.400 .700 .375 .500 1.100 .100 ± E 35,56 17,78 9,53 12,7 27,94 2,54 PE-924XX 1.650 .700 .375 .500 F 41,91 17,78 9,53 12,7 .375 .125 ± .850 .330 .330 .330 9,58 3,18 G 21,59 8,38 8,38 8,38 .650 .280 .280 .280 P H 16,26 7,11 7,11 7,11 K Notes: 1. Typical Inductance occures at I and ET values shown. 5. DCR for vertical part measured close to coil. Add 10% more for low profile part. DC OP 2. Design control test voltage is critical. Inductance increases with voltage. 3. For line filter applications, RMS line current is limited to specified reference DC current. 2 4. LI rating is the ability of the inductor to store energy. 2 For More Information Pulse Worldwide Pulse Europe Pulse China Headquarters Pulse North China Pulse South Asia Pulse North Asia Headquarters Einsteinstrasse 1 B402, Shenzhen Academy of Room 2704/2705 135 Joo Seng Road 3F, No. 198 12220 World Trade Drive D-71083 Herren- Aerospace Technol- Super Ocean Finance #03-02 Zhongyuan Road San Diego, CA berg ogy Bldg. Ctr. PM Industrial Bldg. Zhongli City 92128 Germany 10th Kejinan Road 2067 Yan An Road Singapore 368363 Taoyuan County 320 U.S.A. High-Tech Zone West Taiwan R. O. C. Nanshan District Shanghai 200336 Tel: 886 3 4356768 Shenzen, PR China China Tel: 65 6287 8998 Fax: 886 3 4356823 (Pulse) Tel: 858 674 8100 Tel: 49 7032 78060 518057 Fax: 65 6287 8998 Fax: 886 3 4356820 (FRE) Fax: 858 674 8262 Fax: 49 7032 7806 135 Tel: 86 755 33966678 Tel: 86 21 62787060 Fax: 86 755 33966700 Fax: 86 2162786973 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2015. Pulse Electronics, Inc. All rights reserved. 3 pulseelectronics.com P635.B (02/15)