PULSE PF0560.522NLT

SMT Power Inductors Shielded Drum Core - PF0560 NL Series Height: 4.0mm Max Footprint: 10.4 x 10.4mm Max Current Rating: up to 6.5A Inductance Range: 1.5µH to 330µH 260°C reflow peak temperature qualified Leaded technology compatible 6 Electrical Specifications @ 25°C - Operating Temperature -40°C to +125°C 6 7 8 Inductance Inductance Saturation Heating Core Loss 2,3 5 Part @ OADC @ Irated Irated DCR Current ISAT Current IDC Factor SRF Number (µH) (µH TYP) (A) (mΩ MAX) -35% (A) +30°C (A) (K2) (MHZ) PF0560.152NL 1.5 ±30% 1.5 6.5 8.1 10 6.5 260 >40 F0560.252NL 2.5 ±30% 2.5 6.1 10.5 7.5 6.1 330 >40 F0560.382NL 3.8 ±30% 3.8 5.5 13 6.0 5.5 420 39 F0560.522NL 5.2 ±30% 5.2 5.4 22 5.5 5.4 480 34 F0560.702NL 7.0 ±30% 7.0 4.5 27 4.8 4.5 500 29 F0560.103NL 10 ±30% 10 3.8 35 4.4 3.8 630 25 F0560.153NL 15 ±30% 15 3.1 50 3.6 3.1 790 19 F0560.223NL 22 ±30% 22 2.5 73 2.9 2.5 910 17 F0560.333NL 33 ±30% 33 2.2 93 2.3 2.2 1200 14 F0560.473NL 47 ±25% 47 1.9 128 2.1 1.9 1300 10 F0560.683NL 68 ±25% 68 1.42 213 1.5 1.42 1700 9.0 F0560.104NL 100 ±25% 100 1.25 304 1.35 1.25 2000 6.6 F0560.154NL 150 ±25% 150 0.85 506 1.15 0.85 2400 5.4 F0560.224NL 220 ±25% 220 0.7 756 0.92 0.7 2900 5.2 F0560.334NL 330 ±25% 330 0.52 1090 0.70 0.52 3580 3.2 http://www.power.pulseelectronics.com/contact power.pulseelectronics.com SPM2007_24(08/17) 1 SMT Power Inductors Shielded Drum Core - PF0560 NL Series Mechanicals Schematic PF0560.XXXNL Weight .................1.4 grams Tape & Reel ...........620 reel Inductance vs Current Characteristics Tray .........................60/tray Inches Dimensions: mm Unless otherwise specified, .004 all tolerances are ± 0,10 Notes: 1. Unless otherwise specified, all testing is made at 100kHz, 0.1VAC. 8. In high volt*time (Et) or ripple current applications, additional heating in the 2. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part component can occur due to core losses in the inductor which may necessitate number (i.e P1166.102NL becomes P1166.102NLT). Pulse complies with industry derating the current in order to limit the temperature rise of the component. In order standard Tape and Tape & Reel specification EIA481. to determine the approximate total loss (or temperature rise) for a given application, 3. The “NL” suffix indicates an RoHS-compliant part numer. Non-NL suffixed parts are both copper losses and core losses should be taken into account. not necessarily RoHS compliant, but are electrically and mechanically equivalent to Estimated Temperature Rise: .833 NL versions. If a part number does not have the “NL” version, but an RoHS compliant Trise = [Total loss (mW) / K0] (°C) version is required, please contact Pulse for availability. Total Loss = Copper loss + Core loss (mW) 2 4. Temperature of the component (ambient plus temperature rise) must be within Copper loss = IRMS x DCR (Typical) (mW) 2 2 1/2 specified operating temperature range. Irms = [IDC + ΔI /12] (A) .23 2.38 5. The rated current (Irated) as listed is either the saturation current or the heating Core loss = K1 x f (kHz)1 x Bac (Ga) (mW) current depending on which value is lower. Bac (peak to peak flux density) = K2 x ΔI (Ga) 6. The saturation current, Isat, is the current at which the component inductance drops [= K2/L (µH) x Et (V-µSec) (Ga)] by the indicated percentage (typical) at an ambient temperature of 25C. This current where f varies between 25kHz and 1MHz, and Bac is less than 2500 Gauss. is determined by placing the component in the specified ambient environment and K2 is a core size and winding dependent value and is given for each p/n in the applying a short duration pulse current (to eliminate self-heating effects) to the proceeding datasheets. K0 & K1 are platform and material dependant constants and component. are given in the table below for each platform. 7. The heating current, Idc, is the DC current required to raise the component tempera- ture by the indicated delta (approximately). The heating current isdetermined by mounting the component on a typical PCB and applying current for 30 minutes. The temperature is measured by placing the thermocouple on top of the unit under test. http://www.power.pulseelectronics.com/contact power.pulseelectronics.com SPM2007_24(08/17) 2 SMT Power Inductors Shielded Drum Core - PF0560 NL Series Trise Factor Core Loss Factor Part No. (KO) (K1) PG0085/86 2.3 5.29E-10 PG0087 5.8 15.2E-10 PG0040/41 0.8 2.80E-10 P1174 0.8 6.47E-10 PF0601 4.6 14.0E-10 PF0464 3.6 24.7E-10 PF0465 3.6 33.4E-10 P1166 1.9 29.6E-10 P1167 2.1 42.2E-10 PF0560NL 5.5 136E-10 P1168/69 4.8 184E-10 P1170/71 4.3 201E-10 P1172/73 5.6 411E-10 PF0552NL 8.3 201E-10 PF0553NL 7.1 411E-10 Take note that the component’s temperature rise varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. For More Information Pulse Worldwide Pulse Europe Pulse China Headquarters Pulse North China Pulse South Asia Pulse North Asia Headquarters Pulse Electronics GmbH Pulse Electronics (ShenZhen) CO., LTD Room 2704/2705 135 Joo Seng Road 1F., No.111 Xiyuan Rd 15255 Innovation Drive Ste 100 Am Rottland 12 D708, Shenzhen Academy of Super Ocean Finance Ctr. #03-02 Zhongli City San Diego, CA 92128 58540 Meinerzhagen Aerospace Technology, 2067 Yan An Road West PM Industrial Bldg. Taoyuan City 32057 U.S.A. Germany The 10th Keji South Road, Shanghai 200336 Singapore 368363 Taiwan (R.O.C) Nanshan District, Shenzhen, P.R. China China 518057 Tel: 858 674 8100 Tel: 49 2354 777 100 Tel: 86 755 33966678 Tel: 86 21 62787060 Tel: 65 6287 8998 Tel: 886 3 4356768 Fax: 858 674 8262 Fax: 49 2354 777 168 Fax: 86 755 33966700 Fax: 86 2162786973 Fax: 65 6280 0080 Fax: 886 3 4356820 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2017. Pulse Electronics, Inc. All rights reserved. http://www.power.pulseelectronics.com/contact power.pulseelectronics.com SPM2007_24 (08/17) 3