PULSE PG0426.471NLT

SMT POWER INDUCTORS Flat Coils - PG0426 Series Height: 3.2mm Max Footprint: 7.5mm x 7.0mm Max Current Rating: 60Apk Inductance Range: 0.1µH to 1.5µH High temperature core material, no thermal aging below 150°C Electrical Specifications @ 25°C - Operating Temperature -40°C to +130°C Inductance DCR (mΩ) Part @ Irated Number (μH ±20%) TYP MAX PG0426.101NL 0.10 1.3 1.5 60 34.5 44.4 PG0426.151NL 0.15 2.0 2.2 57 26.0 40.0 PG0426.201NL 0.20 2.0 2.2 46 26.0 53.3 PG0426.221NL 0.22 2.0 2.2 40 26.0 58.6 PG0426.331NL 0.33 3.2 3.4 34 20.0 62.8 PG0426.471NL 0.47 3.2 3.4 26 20.0 89.4 PG0426.681NL 0.68 5.2 5.4 25 15.5 100.6 PG0426.821NL 0.82 7.8 8.0 24 13.0 99.3 PG0426.102NL 1.00 7.8 8.0 22 13.0 121.1 PG0426.152NL 1.50 11.5 11.8 18 9.0 153.6 MECHANICAL SCHEMATIC PG0426.XXXNL .295 .055ā.012 MAX 7,50 1,40ā0,30 .047ā.008 .071 1,20ā0,20 1,80 1 .118 .276 XXXNL 3.00 7,00 DATE CODE(IM/BOM/REV.) 2 MAX .146 3,70 SUGGESTED LAND PATTERN .102ā.012 2,60ā0,30 .126 .472 3,20 12,00 MAX .134 3,40 .630ā.012 .280 16,00ā0,30 7,10 USER DIRECTION FEED TAPE & REEL LAYOUT http://www.power.pulseelectronics.com/contact power.pulseelectronics.com SPM2007 (08/17) 55 SMT POWER INDUCTORS Flat Coils - PG0426 Series Notes from Tables 4. Core loss approximation is based on published core data: Core Loss = K1 * (f) * (K2ΔI) 1. The temperature of the component (ambient plus temperature rise) must be within Where: Core Loss = in Watts the specified operating temperature range. f = switching frequency in kHz 2. The saturation current, ISAT, is the current at which the component inductance drops K1 & K2 = core loss factors by 30% (typical) at an ambient temperature of 25°C. This current is determined by ΔI = delta I across the component in Ampere placing the component in the specified ambient environment and applying a short K2ΔI = one half of the peak to peak flux density duration pulse current (to eliminate self-heating effects) to the component. across the component in Gauss 3. The heating current, IDC, is the DC current required to raise the component temperature 5. Unless otherwise specified, all testing is made at 100kHz, 0.1VAC. by approximately 40°C. The heating current is determined by mounting the component 6. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part on a typical PCB and applying current for 30 minutes. The temperature is measured number (i.e. PG0426.101NL becomes PG0426.101NLT). Pulse complies to industry by placing the thermocouple on top of the unit under test. Take note that the standard tape and reel specification EIA481. component’s performance varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. Inductance vs Current CharacteristicsTypical Core Loss vs Peak Flux Density 1.40 1.0 PG0426.102NL 0.9 100kHz 1.20 0.8 200kHz 1.00 0.7 300kHz PG0426.681NL 400kHz 0.6 0.80 500kHz 0.5 1MHz 0.60 0.4 PG0426.331NL 0.3 0.40 PG0426.201NL 0.2 0.20 PG0426.101NL 0.1 0.00 0.0 14 7101316192225283 34 34043464952 100 200 300 400 500 600 700 800 900 1000 DC BIAS (A) DELTA B (GAUSS) DELTA B = (K2∆I) Typical Component Temperature vs DC Bias Current PG0426.102NL PG0426.331NL PG0426.151NL PG0426.471NL PG0426.152NL PG0426.681NL PG0426.201NL 100 PG0426.221NL 80 PG0426.101NL 60 40 20 0 06 12 18 24 30 36 42 48 54 DC BIAS http://www.power.pulseelectronics.com/contact power.pulseelectronics.com SPM2007 (08/17) 56 INDUCTANCE (µH) COMPONENT TEMP. RISE (ºC) CORE LOSS (W)